Part # PL2672
Manufacturer Code SPX2610C
Dimensions 4.4" X 0.7"
This is an Aftermarket Replacement Impeller For the Hayward® Super Pump™ 1.5 T.H.P (Total Horse Power) and not the Hayward® original O.E.M Impeller.
Impeller for 1.0 HP full rate and 1.5 HP up rate pumps. Used on several Hayward® pumps including the Max-Flo, Super Pump, Power Flo II and Power Flo III as well as Leslie's® Hydramax pump.
Easy Homeowner Installation
Watch How To Replace A Pool Pump Impeller
Disclaimer:
All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only.
pump will not flow, lost prime
Reply
There are number of reasons that can cause a pump to lose prime. A clogged line, dirty or old filter, air in the lines, suction air leak at a line or valve, clogged impeller, or even a bad glue at a suction or pressure pump fitting. In any regard either going through the process of elimination testing each possibility or getting a technician to the site would be the next course of action.
Reply
I recently purchased this impeller. the pump motor is a 3/4 HP. I see that this impeller is rated for 1HP. Could using this impeller cause the motor to overheat?
Reply
Hi, Lou I. In order to use the SP2610C impeller you would need a Full Rate 3/4 HP Motor, not an Up-Rate 3/4 HP that's why the motor is overheating. You will need the SP2607C Impeller.
Reply
Hi, If i was mistakenly using a SPX2610C impeller on a SP2607X102S dual speed motor, could this be the reason my motor would overheat and shut off on high speed and function normally on low speed?
Reply
Hi, Shane. Yes, that will explain why your pump is overheating on high speed. The impeller is too larger for the motor. You will need to either increase the motor to STS1102RV1 or decrease the impeller to SPX2607C.
Reply
I'm replacing my 1.5 horsepower motor on my system and want to also replace any parts that may need replacing. The impeller is part number SB2610-C and the existing one looks good but I can't easily turn it by hand. Does that mean it is ready to be replaced?
Reply
Hello,You would only need to change the motor.
Reply
Hi, If i was mistakenly using a SPX2610C impeller on a SP2607X102S dual speed pump, Could this be the reason my pump overheats and shuts off on high speed but works normally on low speed?
Reply
Hi, Shane. Yes, that will explain why your pump is overheating on high speed. The impeller is too larger for the motor. You will need to either increase the motor to STS1102RV1 or decrease the impeller to SPX2607C.
Reply
1 to 2 hrs
5/16 Allen wrench
I replaced the original impeller in the Hayward Super Pump 2600 to match with the high RPM variable speed pool pump motor I installed. I was not difficult to install but did require the purchase of a 5/16th Allen wrench. My set that IO've had forever, largest size was 1/4. Maybe could have used it, as all you need it for is stabilizing the motor shaft to hand tighten the impeller. But I did not want to mess anything up so I bought a new set of Allen Wrenches that included a 5/16th Allen wrench. I'll give my old set to my Son.
Less than 1 hr
Wrench Set
1 0
Upon inspection I discovered the old impeller broke therefore no water was being pumped. Ordered a new impeller for my Hayward Sp and installed it myself. Problem solved. No high cost parts or installation. All DIY and Inyo pools had the best prices.
The Most Recent Reviews
(5 out of 5 stars) Perfect Fit!
Reviewed By: Inyo Customer ()
Worked perfectly on my Hayward Super Pump. Sized for my 1.5hp motor! Very happy
Was this review helpful to you?
(5 out of 5 stars) Nice update!
Reviewed By: Inyo Customer ()
Fits perfect with century motor
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
OE quality fitment!! Could not be happier!!
Was this review helpful to you?
(5 out of 5 stars) Great
Reviewed By: Inyo Customer ()
Great
Was this review helpful to you?
(5 out of 5 stars) INYO how-to videos are the best
Reviewed By: Inyo Customer ()
Works great and easy to install. INYO how to videos are the best.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good product easy to install
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
When I removed the old Impeller the shaft on it had 2 cracks in it, the shaft was made of plastic. This new impeller has a brass shaft attached so no way it's going to crack.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect fittment for my part t placement
Was this review helpful to you?
(5 out of 5 stars) Hayward Impellar
Reviewed By: Larry B. from Venice, FL ()
Pros: none
Cons: none
Impeller broke and was not providing any suction. Ordered new pool pump, and this, installed, works great.
Was this review helpful to you?
(5 out of 5 stars) Inpeller just what I needed
Reviewed By: Reagin P. from TX ()
Easy to find on website and just what I needed!
Was this review helpful to you?
(5 out of 5 stars) Improved Design
Reviewed By: Ticup from Cumming, GA ()
Pros: Easy ordering of pump parts
Original was all plastic and failed at the hub. The new impeller has a brass hub and threads, a stronger design, IMO.
Was this review helpful to you?
(5 out of 5 stars) Impeller
Reviewed By: Hot tub from Elk River, MN ()
I am completing a replacement on a hot tub pump motor. This impeller was shipped quickly and appears to be a perfect fit.
Was this review helpful to you?
4 0
(5 out of 5 stars) Hayward Super Pump Impellor
Reviewed By: Robert R. ()
FINALLY!! Hayward finally made the threaded shaft out of brass. Hopefully it will outlast their pump. Prior to this improvement it had a plastic shaft that wore out from fatigue they cracked and broke. Hayward pumps would be ideal if they would make the commitment to make them waterproof and out of materials that lasted....like this improved part.
Was this review helpful to you?
(4 out of 5 stars) Impeller
Reviewed By: Allen O. from Enterprise, AL ()
Good product easy to install
Was this review helpful to you?
(3 out of 5 stars) purchased impeller but salesman gave no recommendation
Reviewed By: Kimberly D. from Modesto, CA ()
Pros: price
Cons: lack of customer service
Impeller was fine however the salesman should have recommended getting the gasket. Realized that we needed it after the new part arrived and it looked slightly different.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Robert J. from Albuquerque, NM ()
Following your expert advice,this impeller works perfectly in my 25 year old pump.
Was this review helpful to you?
(4 out of 5 stars) Impelller replacement works great
Reviewed By: Ron A. from Mint Hill, NC ()
Impeller works great, delivered on time
Was this review helpful to you?
(4 out of 5 stars)
Reviewed By: Paul C. from Gonzales , TX ()
i was happy with service and customer was to thanks
Was this review helpful to you?
1 0
(5 out of 5 stars) Well built - metal threads!!! Designed for 1HP
Reviewed By: David T. from Oxford, OH ()
Pros: Well built....easy to install
Cons: None
I had dealt with local pool store and have purchased 3 of these impellers. They were selling me the wrong part (plastic threaded hub) and that is why they failed. I have a 1HP pump and this impeller has a metal threaded sleeve pressed into the part. InYoPool helped me finally select the right part and it has performed very well.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Walter Martin from Miami, Fl ()
The product arrived on the time that was expected and was perfectly replaced.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Herm from Nashville,TN ()
Pros: Great Product & Service
Cons: None
The product was as the origional and all the descriptions and diagrams were very helpful.
Was this review helpful to you?