$77.59

Qty:

By Hayward Pool Products


Details

Top

Part # 4810-19

Manufacturer Code ECX1104

Dimensions 13.25" L x 13.25" W x 0.46" D

Alternate Part #'s EC1104, ECX1104, HAY0511836, 14-150-1120, HAY-051-1836, HAYECX1104, HPPECX1104

Product Description

Tube Sheet (ecx1104)

Top

?     Asked on 4/3/2017by DENNIS

I have a Hayward EC60 , I need the plate that the tubes go in and some new tubes and covers! All I see are EC65'S? Any help would be appreciated ! Thank you in advance : Denny
 Reply

A  Answered on 4/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Dennis. The EC65 parts will fit the EC60 as far as the parts you need, click link to view Complete part listing for Hayward Perflex Filter Series II EC-60.
 Reply


Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Nut Drivers

1     0

Tube sheet cracked

Written on 8/11/2018 by Guest

Remove filter tube/cover assembly from the filter housing.Remove bump handle by removing the retainer bolt. Remove cover to separate tubes. Remove 16 small bolts to separate the upper and lower plates. Remove all flex tubes from the lower plate and install them in the new plate. (Be patient, these may be held in the old plate due to DE build-up) Remove and reuse the center shaft, Replace o-rings if needed. Reassemble filter parts

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

2 to 4 hrs

Tools Needed

Screwdriver, Nut Drivers, Pliers, Socket Set

2     0

Original part was cracked around the center hole for the shaft. Back pressure was too high due to dirty tubes. Leask from top of DE filter.

Written on 6/5/2017 by Guest

1. Disconnect the bump lever by unscrewing the self locking nut and withdrawing the screw from the shaft.
2. Remove the bolts and nuts around the filter top and remove the top.
3. Lift our the tube nest, flush off any caked on DE material, and very carefully check the plates for cracks in the center near the shaft and any other damage.
4. Remove the C-Clips on the bump shaft and remove the shaft, remove the rubber O-rings
5. Remove the screws and nuts holding the the two nest plates together and separate the plates. Identify the upper and lower plates and their orientation. Remove the large gasket.
6. Remove all the filter tubes, clean using the INYO cleaner solution and further clean and flush using something like Simple Green concentrate.
7. Examine tubes for damage and replace as necessary.
8. Replace tubes in the lower plate making sure they lay flat and the the opening is not obstructed by the fabric.
9. Align the upper plate correctly so the holes match the lower plate, position a new large gasket. (bend in the gasket faces down)
10. Replace and tighten all the screws and nuts evenly.
11 Use 600 grit sandpaper and clean any corrosion from the bump shaft
12. Put new O-rings on the shaft and lubricate with pool grease. (If you put the O-Rings on first insert the shaft top to bottom, Otherwise insert it bottom to top and put the rings on after it is secured)
13. Replace the shaft in the nest, top side (withe the bump lever hole) up and replace the C-Clips and washers..
14 Replace the check valve and o-ring in inlet to the DE filter by removing the elbow in which the valve sits. Replace the elbow.
15. Position the nest in the top of the filter carefully making sure the gasket is flat and in its groove, use pool lube.
16 Replace the top aligning correctly relative to the inlet and outlet ports.
17. Insert the screws and nuts and tighten evenly and fully. There will be a definite stop felt when they are fully home.
18. Reattach the bump lever.
Done

Were these instructions helpful? 
 

Top

Review Summary

 (Average 5  out of 5 stars)
3 Rating
5 star:
 
(3)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Recent Reviews