$37.30

Qty:

By Custom Molded Products


Details

Top

Part # 25830-704-800

Dimensions 4" L x 4" W x 2" D

Alternate Part #'s 25830-704-800, 7056, _25830-704-800, CMP25830704800

Product Description

THIS IS THE GENERIC VERSION OF THE JANDY # 7056 WHICH IS USED ON THE JANDY CHECK VALVES. ALL VERSIONS, BOTH STRAIGHT THRU AND 90 DEGREE INCLUDES #7451 FLAPPER, # 7302 SPRING, # 7304 PIN, # 7236 COVER, AND # 1132 COVER O-RING ONLY THE COVER O-RING IS AVAILABLE AS A SEPERATE PART THE OTHERS ARE ONLY SOLD AS PART OF THIS KIT

Top

?     Asked on 1/2/2015by Sid Beaumier

Will this replacement part work on a Jandy Check Valve part number 7236?
 Reply

A  Answered on 1/5/2015 by InyoPools Product Specialist Robert M.

Yes, CMP part number 25830-704-800 will work with your Jandy check valve.
 Reply


?     Asked on 12/17/2018by Ray

will this work on a Pentair ck. valve ?
 Reply

A  Answered on 12/17/2018 by Industry Professional

Hi, Ray. No, this will not work with a Pentair check valve.
 Reply


?     Asked on 4/18/2020by Gary

Will this fit my Jandy 7236 check valve
 Reply

A  Answered on 11/6/2020 by InyoPools Product Specialist Hector F.

Hi Gary, yes this cover assembly is compatible with the Jandy 7236 check valve. The 7236 is actually the cover part number. 
 Reply


?     Asked on 1/18/2021by Inyo Visitor

Is the spring stainless steel?
 Reply

A  Answered on 1/20/2021 by InyoPools Product Specialist Joe S.

Yes, the springs used in the check valve would be stainless steel.
 Reply


?     Asked on 4/23/2021by John Schrader

My pool has a defective jandy anti siphon valve, but I cannot find a part number on it. It says "check valve" on it, but no part number. Would your part work on this one? The valve was installed in 2001 or 2002
 Reply

A  Answered on 4/23/2021 by InyoPools Product Specialist Craig C.

Hello.  If your current Jandy check valve has a clear top, is fastened with 8 screws, then this replacement part will fit the existing check valve body regardless of the install date.  To be certain please compare the attached picture of the replacement valve cover assembly to the existing check valve.  Swimming Pool Check Valve Cover Assembly w/ Flapper & O-ring - 25830-704-800
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

The tabs for the Flapper assembly cracked and the o-ring was leaking

Written on 3/2/2020 by Guest

Purchased a new Cover Assembly w/ Flapper & O-ring - 25830-704-800. Removed the old assembly. Put some o-ring lube on the new o-ring. Tightened each screw lightly in a even zig zag pattern. Then went around again to each screw and firmly tightened in a zig zag pattern.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

Rubber Seal on Flapper Ripped

Written on 5/6/2019 by Mack

1. Remove screws from the Cover Assembly and lift Cover Assembly from its
receptacle.
2. Insert new Cover Assembly w/Flapper & O-ring into the receptacle.
3. Replace and tighten the screws hand tight only!

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

2     0

My spa was losing water back into the pool when pool pump was off due to wore out check valve.

Written on 4/20/2017 by Guest

Shut off pool pump
Knock breaker for pool pump
Use Phillips head screw driver
Removes screws to check valve (8)
Take out check valve
Note water flow direction (usually arrow on check valve)
Feel inside to make sure no obstructions where valve seats
Apply silicone lube on new check valve o ring
Place check valve into open slot (nite water direction flow)
Re install Phillip screws
Tighten in star pattern
Reset pool breaker
Turn on pool pump
Check for leaks
Job completed
Good job!

Were these instructions helpful? 
 

Top

Review Summary

 (Average 5  out of 5 stars)
10 Rating
5 star:
 
(10)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews