Does this item come with the o ring
Reply
No the PO12728O1 O-Ring is not included.
Reply
Good day,
I have a Stark pool pump; model 75115 - 1.5HP... Will this pump cover be the correct replacement for the pump?
Reply
Hi, The Pool Pump Cover (PO12728CR) is the correct pump lid that can be used with the Stark Pool Pump 75115.
Reply
We just bought this house and it came with a pool but the pump is missing the lid. It says its an Avalanche 150eh. I can not find anything that says Avalanche. Do you know?
Reply
Hello, I did some extensive research on this and I did get a single return result from Google about an Avalanche related to a pool pump and filter combo, but there was no additional information provided. Unfortunately there was no additional information I could find.
Reply
I have a Doheny 7230 pump 1.5 hp will this lid fit
Reply
Hello, Yes, this lid will fit PUMP MODEL #'S 72728, 72729, 72730, RELBC272728, RELBC2729, RELBC2730, 12728, 12729, 12730, NE6151B, NE6171B, NE6181 & NE6183
Reply
looking for parts to stark usa pool pump
Reply
The Above Ground Pool Pump - Blue Wave, Dohenys, Splash Parts is the only reference we have for any Stark Pool Pump parts.
Reply
Will this lid fit model Stark #75117 ? If not, do you have the lid that does?
Reply
Hello Kathleen, I would check dimensions on the hook up it does fit a Stark 75115, not sure about the model 75117.
Reply
Does it fir model 75039
Reply
Hello Constance, the lid goes to In Ground Pump (1-1/2" Ports) - Splash, Splash Pool Parts, Above Ground Pool Pump - Blue Wave, Dohenys, Splash Parts and Splash In Ground Pump (2" Ports) Parts. The model 75039 didn't come up with anything so check pump housing on the side of basket to see if make and model are what is listed above.
Reply
I have a new pump that was just discontinued and the pump cover broke. The serial #SP1603102457, Model #SP-10-1N11CB, Part #3410413-1502. The inner edge of the ring is 6 ". Will this cover fit even though it does not look the same?
Reply
I have stark usa 75117. Does this lid fit and does it come with I ring. I seen answers where some say it did and some says it doesnt. Just needing to know what all I need to get.
Reply
I Have this pump cover and see thru plastic has come loose and is sucking air taking away pressure. Can I repair it ?
Reply
Hello Gary, you might want to check if there is any stress cracks on the housing. Also with the oring, take the lid off and whip down any residue that could cause compromising the seal. Once cleaned, put a layer of lube and let cure for a minimum of 2 hours to create a seal.
Reply
Will this fit Reliant BC2715?
Reply
Hello Terry, Yes the BC2715 will be the FOLLOWING PUMPS: PURELINE PURE PRO XL, BLUE WAVE TIDAL WAVE PUMP, BLUE WAVE MAXI PUMP, BRIDGING CHINA, DOHENY'S, RELIANT, POOLINE, PURELINE, ROARING RIVER, SPLAPOOL, SPLASH, SPLASH POOL, SPLASH POOL APPLIANCE & STARK USA. PUMP MODEL #'S 72728, 72729, 72730, RELBC272728, RELBC2729, RELBC2730, 12728, 12729, 12730, 75115, 75117, NE6151B, NE6171B, NE6181 & NE6183.
Reply
I have a Hayward model A2730 or RS4G24913L depending on where you look.
Will this cover fit my pump?
Reply
Hi, Dean. None of those number cross-reference to a Hayward pump. However, this Cover will fit the follow pumps, PureLine PL16, Splash, Splash Pool, Stark USA, PureLine PL15, Blue Wave, Dohenys, Splash, Stark USA and Splash In Ground Pump (2" Ports).
Reply
Will this work on SPLA pool and spa pump model# 72729?
Reply
Yes, that is correct. Here is the complete parts page to the pump http://www.inyopools.com/parts_above_ground_pool_pump_bridging_china_reliant_blue_wave_dohenys_.aspx
Reply
I have a Stark Pool Pump that the strainer pump cover cracked. The pump is model #75115. when I measure the size with a caliper it reads 5 55/64 can you get one that size
Hello, This will be the correct lid for your pump.http://www.inyopools.com/Products/00101352076358.htm
Reply
I need a Replacement Pump Basket Cover for Rx Clear Mighty Niagara Pump| In-Ground Swimming Pool | Single Speed |2 HP Pump | Electrical Hookup 115V or 230V, 230V set at Mfg | 7/14 Amps. Can you please advise where I can purchase that. Thanks
Reply
Hi, Monica. Based on the info that I was able to locate, this Pump Cover - PO12728CR will fit that pump. Other replacement parts are listed on the In Ground Pump (1-1/2" Ports) Parts Diagram.
Reply
I have the PL1615 and need a replacement lid. I found PO12728CR, is that the correct replacement part for my pump? Also, does this lid come with an O ring or would I need to purchase one as well?
Reply
I have the PL1615 and need a replacement lid. I found PO12728CR, is that the correct replacement part for my pump? Also, does this lid come with an O ring or would I need to purchase one as well?
Reply
Good morning. I have the Pure Pro xl model #PL1501. The top of the pump over is leaking. Looks like it is coming out around where the glass is on top of the cover. Do I need a new cover or just the Oring?
Reply
Hi Kim, I think you should be fine with just replacing with this Lid O-Ring
Reply
I have a motor model number DZQD7502 that I purchased from you last year or the year before. I need to replace the basket cover and cannot seem to find this model number. Can you please help? I've attached a photo.
Thank you.
Could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendations.
Reply
Will this replace a Harris pool pump lid? It’s the exact diameter of the current one. Both lid ring and clear plastic
Reply
Hi Chris, yes this is a replacement for the Harris pool pump lid. Right now we are out of stock on this lid but we do have more arriving into inventory around June 15th, 2021. If you are in need of this lid I would suggest ordering now as we already have a lot of back-orders for the lid and the inventory that will be arriving in June we will sell through pretty quickly. If you order now then you will save your place in line for the lid.
Reply
Does this part come with the O-ring? I just received the lid and it does not appear to have one. What O-ring should I get?
Thank you
Reply
Hi, The O-Ring is not included, you will need this PL1586 O-Ring
Reply
Will this lid fit a hydrotools pump basket?
Reply
Yes this is the correct replacement lid for the Hydro Tools pool pump. There is one exception, however that lid looks completely different. So in short if you have a Hydro Tools pump and the lid looks similar to this one then yes this is the correct lid.
Reply
looking for Rx Clear part # 47252772 will this work
Reply
Hi Jeffrey, Yes this is a replacement for Rx Clear part # 47252772. Currently, we are expecting our inventory around June 15th, 2021. I would suggest clicking the "Notify When in Stock" icon in the upper right-hand corner of this page and you will be notified when our inventory comes into stock.
Reply
I have a Harris Pool Pump 1.5 HP inground...and the part is the Clear Cover part # 16578
Will this fit our pump trap cover?
Reply
Hello Shane. According to the manufacturer, the Pureline Pool Pump Lid part number PL1585 is a compatible replacement for the Harris Pool Pump Clear Cover part #16578.
Reply