?     Asked on 1/11/2012by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


?     Asked on 1/12/2012by Guest

Why do I need to purchase a new shaft seal?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
 Reply


?     Asked on 1/12/2012by Guest

Why should I purchase a Tune Up Kit?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
 Reply


?     Asked on 8/27/2015by Kurt

does this work on Hayward super pump?
 Reply

A  Answered on 8/28/2015 by InyoPools Product Specialist Matt S.

The UQC1072 is not compatible with the Hayward Super Pump as this motor is a square flange, and the Super Pump uses a round flange motor. The round flange equivalent to the UQC1072 is the UCT1072 A.O. Smith 3/4 HP Energy Efficient Motor
 Reply


?     Asked on 6/16/2016by mick

i'm looking to replace my magnetek centurion part #168451, will this motor be an acceptable replacement? Also what would be the difference or advantage of this motor vs the usq1072?
 Reply

A  Answered on 6/17/2016 by InyoPools Product Specialist Scott W.

All three of those motors have the same total horsepower, the difference is going to be the amount of amps being used. The energy efficient motor is going to use about 25-30% less amps while putting out the same amount of horsepower.
 Reply


?     Asked on 5/6/2017by Victor Hardy

I am in search of a replacement motor for my sta rite max e glas pool pump. K48K2PA105C1 3/4HP 48Y frame Will this motor fit my pump? Exact Fit? Thanks! Victor
 Reply

A  Answered on 5/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Victor. The Century QC1072 motor is the correct replacement motor, not the UQC1072.
 Reply


?     Asked on 5/22/2017by Sue

I'm looking to replace my Dura Glas A.O.Smith .75HP (.95 THP) full rate pool pump motor with an Energy Efficient A.O. Smith 3/4 H.P Square Flange Up Rate Motor - UQC1072. Is this the right one?
 Reply

A  Answered on 5/22/2017 by InyoPools Product Specialist Hector F.

No, the correct motor model would be part number 5321-1.
 Reply


?     Asked on 5/23/2017by Jason

Will this motor work for a replacement on pentair whisperflow Wfe-3 /011512?
 Reply

A  Answered on 5/23/2017 by InyoPools Product Specialist Hector F.

If you are needing a replacement motor that matches the original motor then it is the B661.
 Reply


?     Asked on 7/5/2017by John

What gaskets do I need for this motor,
 Reply

A  Answered on 7/22/2017 by InyoPools Product Specialist Alex V.

John, The gaskets will vary depending on what model pump do you have. Do you know your pump model? 
 Reply


?     Asked on 7/6/2017by Inyo Visitor

Would the UQC1072 replace an emerson EB852
 Reply

A  Answered on 7/6/2017 by InyoPools Product Specialist Lennox H.

Hi. Yes, this Century UQC1072 Motor can be used as a replacement for the Emerson EB852 motor.
 Reply


?     Asked on 4/15/2018by Mike

I have a Sta-Rite Max E Glas PEA 5D 180L and a K48J2PA105C1 is the UQC 1072 the proper replacement motor
 Reply

A  Answered on 4/16/2018 by InyoPools Product Specialist Hector F.

Yes, this motor would be a compatible replacement motor for that model. 
 Reply


?     Asked on 5/7/2018by Ts

Is this the correct replacement motor for a sta rite max e glass 2 motor ?
 Reply

A  Answered on 5/8/2018 by InyoPools Product Specialist Hector F.

Those pumps can sue multiple motor models so you would need to know the specific motor model, part or catalog number. If that is not present then you may need to locate the impeller part number which is usually molded onto the plastic of the impeller itself. 
 Reply


?     Asked on 11/6/2018by Joseph Stakun

i have a P,entair pool pump and need a replacement motor. The existing motor is P/N 7-186236-20, FR P56Y, type CX, 3/4 HP. Which is the correct replacement for this? Thank you

 Reply

A  Answered on 11/6/2018 by InyoPools Product Specialist Lennox H.

Hi, Joseph. he Century B2852 motor is the correct replacement, however, you can also use this UQC1072 as an energy efficient replacement. 
 Reply


?     Asked on 7/21/2019by Christopher Beck

i need to replace my pool pump motor. inground pool. A.O Smith, sta-rite, dyna glas, model:C48J2PA105C1
 Reply

A  Answered on 7/23/2019 by InyoPools Product Specialist Hector F.

Your replacement motor is the model SQ1052
 Reply


?     Asked on 4/5/2020by Wilbur

I have a Harris pump model#152716 motor#cs4m2491L 1hp 48 frame . will this motor fit my unit
 Reply

A  Answered on 4/7/2020 by InyoPools Product Specialist Patrick P.

Hi Wilbur, Do you know if you are wiring your pump 115v or 230v? If you are wiring 115v then this motor here will work 1 HP 115v Replacement Pool Motor
 Reply


?     Asked on 5/8/2021by Eric Gleiss

I have a Sta-Rite model P2RA-5D-180L pool pump with an AOsmith model K48J2PA101A2 motor with specs. as follows 3/4 HP, voltage 115/230, 9.6/4.8 amps, 3450 rpm,48Y frame, 1.27SF. I would like to know if I can replace this motor with INYO pools item UQC1072.
 Reply

A  Answered on 5/9/2021 by InyoPools Product Specialist Patrick P.

Hi Eric, Yes the UQC1072 is the correct replacement motor. You will need this Sta-Rite Dura Glas Seal Kit Pre 1998 or this Sta-Rite Dura Glas Seal Kit 1998 and after. If you don't know if your pump is from before or after 1998 then we put together this Video on How to Determine if your Sta-Rite Pump is Before or After 1998.
 Reply


?     Asked on 4/22/2022by Michael Smith

My Pinnacle Pentair Motor Model #196238 has failed. Is this Century 3/4 HP Square Flange 48Y Up Rate EE Motor - Part # UQC1072 the correct replacement? Does it come with a 30A plug attached? Thank you, Mike

 Reply

A  Answered on 4/22/2022 by InyoPools Product Specialist Craig C.

Hello Michael.  The Century Motors model UQC1072 (THP 0.95) 48Y Frame is not the best replacement for the Pentair Motor model 355020S (196238) (THP 1.24) 56Y Frame.  The Century Motors model B2853 (THP 1.25) 56Y Frame is the better replacement.  B2853  It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced concurrent with the new motor.  The GOKIT24 contains the parts necessary to complete this project.   GOKIT24   Attached please find the Pentair Pinnacle exploded parts diagram for reference.  Pentair / Pac Fab Pinnacle
 Reply


?     Asked on 8/14/2022by Leah Istre

I have the motor that was purchased a couple of years ago. The seal plate is broken. What is the replacement part for it.

 Reply

A  Answered on 10/1/2022 by InyoPools Product Specialist Hector F.

Hello Leah, the correct seal plate for your Sta Rite Dura Glass series pool pump is part number 5056-05
 Reply


?     Asked on 9/14/2022by CAROLYN LAUN

Is this the right replacement motor for my pool pump?

 Reply

A  Answered on 9/15/2022 by InyoPools Product Specialist Craig C.

Hello Carolyn.  The Century 3/4 HP Square Flange 56Y Full Rate EE Motor - B2661 is the direct replacement motor for the Magnetek/Century Centurion motor model B2661, 8-165198-06.  
 Reply