My heat pump runs for approx twenty minutes then stops,then it seems to defrost leaving a pool of water on heat pump bottom?
Reply
Hello Morton - Depending on you geographical location, this may be a normal operating procedure. Please see page 55 of the Aquacal Manual to see if this is the situation you are in. If not, please contact Aquacal at 727-823-5642 for further assistance.
Reply
Hello, I have an Aquacal Heat pump model 115ahdsbtb with a code of "OTA". This code came up shortly after turning on the spa. It has disabled the heat pump. There are no other indications of any problem and the water did not even heat up. I suspect it is a faulty temperature sensor. If this is the case, which temp sensor would I replace? Is it the one in the housing of the heat pump on the 2" inlet PVC pipe? Can I test this first by cutting one of the wires or tying the 2 wires together?
Reply
Yes, that would be the correct replacement part for the temperature sensor, but I do not have the error codes for that. I recommend you give AquaCal a call at 727-823-5642 so they can tell you what that error code means.
Reply
My Aquacal pool heater works but the actual water temp is incorrect, read 99 when the water temp is more like 75. I can get it to turn io by setting it to "spa" and uping the set temp to above the 99 degrees. Is this a sensor problem, control problem of something else?
Reply
Hi, Brad. It sounds like you have a temperature sensor issue.
Reply
I have a leak around the temp sensor, and the temp sensor is lose. Is there a boot or some sealant that is supplost to be in the sensor hole?
Reply
Good Morning Mr. Webb, Hope you are doing well. This sounds more like a leak in the sensor well than a problem with the sensor itself. I will need your model number to see if you need the 1113KIT copper well kit or the STK1113A plastic well kit. Thanks, Robert Brown AquaCal Tech Support
Reply
Good Morning Mr. Webb, Hope you are doing well. This sounds more like a leak in the sensor well than a problem with the sensor itself. I will need your model number to see if you need the 1113KIT copper well kit or the STK1113A plastic well kit. Thanks, Robert Brown AquaCal Tech Support
Reply
do you happen to know what the major difference is between the plastic or the copper? besides the price.
Reply
I need a water temp sensor for a Aqua Cal SQ110. Where can I get a replacement?
Reply
Hello, This will be the part you need, http://www.inyopools.com/Products/00601352067015.htm#qaIt also comes with the defrost sensor as a package.
Reply
I have an aquacomfort pool heat pump (manufactured by G&S Mfg or Gulfstream out of Florida). Control panel shows "Evap Sensor Malfunction". After reading the service manual online it says it's the defrost sensor. I opened up the unit, connections are all fine, so looks like I need to replace. Repair manual says it's a 10K sensor. Another company wants to charge me $124 for OEM part, looks to me like the one you are selling would work fine. Can you offer any guidance?
Reply
Good Morning Victor, Hope you are doing well. This kit number STK0021 is a 10 k sensor that should work for this situation. The only thing I cannot verify is how the sensor will mount to their control board. You may need to do some modification to the sensor. INYO can assist you with pricing & ordering. Thanks, Robert Brown Aquacal tech support
Reply
I have a rather old AquaCal AEROTEMP - AT8500 (?? Label is worn - ~18 years old) - This year, water temp reading of 120 so compressor does not actuate.
Also, there is a leak @ the Temp sensor - Also, the threaded ring on the inside of the manifold cracked this past winter not sure how to fix this w/o replacing.. the inside diameter of the opening is just under 2" but replacing the manifold = hard. Ideas? suggestions? see the attached pics The unit has been flawless until this season.
Good Morning Mr. Harrison, Hope you are doing well. The 2 parts I would suggest in this case are the STK0021 temp sensor kit pictured above & a new manifold D160278S. It is more difficult to replace, but is much better than trying to piecemeal this together. Please see attached image of manifold. Thanks, Robert Brown AquaCal Tech Support. If you are interested in the manifold kit then reply back to this post and Inyo can get you a price.
I have a AquaCal Heater/Chiller Model # 120ARDSBPR that shows me a temperature error. Do you carry a water temperature sensor replacement?
Hi, Marley. This Water Temperature / Defrost Sensor Kit is the correct replacement for your model.
Reply
Will this work for model SQ125AHDSBPB? My pool temp is 80 & I have moved the heater temp to 101 & it’s not running. I increased to 104 to get it to run. This is what I should replace?
Reply
Good Morning Phillip, Hope you are doing well. If the heater is reading your water temp on the display as 80 and the actual pool temp is 80, then I do not think you have an issue with the sensor. It is possible that you have an issue with internal programming on the heater or some other internal issue that is keeping the unit from running. I would suggest contacting AquaCal at 727-823-5642 to troubleshoot further. Thanks Robert Brown AquaCal Tech Support
Reply
I have an AT12000 serial # 401149-C01. Just opened for the season in New England and think I have a water temp sensor issue. The WT display was bouncing radically from 84 - 86 initially then up to 95 - 96. I know the water temp is much lower around 55 - 60. The fan came on initially, then off...then on a the comp kicked on for a while when I set the heat temp to max 95 degrees, then off. Now water temp reads 95 and the fan won't come on as it thinks the the max temp is achieved. Help!
Reply
Good Morning Rich, Hope you are doing well. This is most likely an issue with the water temp sensor and can be fixed with the STK0021 temps sensor kit listed on this page. Thanks Robert Brown AquaCal Tech support
Reply
Thanks, are there instructions on installing the sensor with the kit? Is this a delicate operation so as not to crack the housing? Is removing the top the best way to get at this area?
-6105D.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-6105D.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "AquaCal WATER TEMPERATURE / DEFROST SENSOR 10K OHMS (STK0021) - 6105D")
Hi,
Looking for a replacement temperature sensor for a Aquacal , Model: 075HHDSBNB . Do you have any? and do you ship to NZ
-6105D-91759726-04e3-4633-ae6d-583c8c4a4992.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-6105D-91759726-04e3-4633-ae6d-583c8c4a4992.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "AquaCal WATER TEMPERATURE / DEFROST SENSOR 10K OHMS (STK0021) - 6105D")
Hi Christine, this WATER TEMPERATURE / DEFROST SENSOR is the correct temperature sensor for your Aquacal 075HHDSBNB heater. Obtaining an international shipping quote is easy. Add the items to your shopping cart by clicking the "buy now" button, and continue the order process as if you are buying the item(s). Your credit card will NOT be charged at this point. You'll first receive an email that will list the shipping charges to your country and inform you of any items that cannot be shipped outside the US. You will then be given the option to accept these charges to process the order or decline them which would cancel it. Your credit card will only be charged if you accept the freight. International orders are subject to customs, tax or duties imposed by your local government. There is a $9.95 handling fee for Canadian shipments & a $15.00 handling fee for all other international countries.
Reply
I have an Aquacal Tropical T090 model number 090AHDSBPH heat pump and was getting error code that indicate my temperature senor needs replaced. is this the correct on to replace it.
Reply
