?     Asked on 3/5/2015by Inyo Visitor

will the aql-ww-p4 work on the plp4 pro logic control
 Reply

A  Answered on 3/5/2015 by InyoPools Product Specialist Wes B.

unfortunately no, The correct part number you would need is (2807-80) wired remote, Ps-4 Wall mount, white plog (glx-ww-ps-4)
 Reply


?     Asked on 5/19/2015by Georges

Hi my wall mounted wired control ,the little arrow on the right side of the menu button isn't working,you think it's the panel or the card?Also my control outside in the box the led display is not showing anything,control or card ?Thanks
 Reply

A  Answered on 5/19/2015 by InyoPools Product Specialist Patrick P.

Hi Georges, Based on the fact that you are having issues both at the indoor remote and at the outdoor power center it leads me to belive that your issue is the Aqua Logic PC Board.  Please make sure you have the Aqua Logic Control system and not the Prologic Control System as they look very similar. If you do have the Pro Logic then you will require the ProLogic PC Board.
 Reply


?     Asked on 5/26/2015by Georges

Hi now i'm getting error Check system no cell power 2....What does that mean and how can I fix it?thanks
 Reply

A  Answered on 5/26/2015 by InyoPools Product Specialist Patrick P.

Hi Georges, "No cell power" means no power to the circuit board and that your AquaLogic PC Board (GLX-PCB-Main) Needs to be replaced. Replacing your PC board should do the trick.
 Reply


?     Asked on 5/11/2017by Inyo Visitor

My red light comes on saying low salt, but I have had the salt level tested and the numbers are correct. Been told the cell is reading wrong and the cost to replace the cell is $600. Would I not be better and less expensive to just replace the entire computer?
 Reply

A  Answered on 5/12/2017 by InyoPools Product Specialist Hector F.

No, not necessarily. You may need to just replace the cell so I would recommend having the cell tested first at a local pool retailer. If it is showing as bad then that should be replaced first.
 Reply


?     Asked on 2/12/2018by Dennis

My AQL-WW-P4 loses sometimes an hour every 6 hours, sometimes it's fairly close, what's wrong?
 Reply

A  Answered on 2/13/2018 by InyoPools Product Specialist Lennox H.

Hi, Dennis. The issue could be the Main PCB are experiencing the same issue. If just the inside wall unit is losing time then the wall controller is going bad. Replacement parts are not available so you will have to replace it. 
 Reply


?     Asked on 3/27/2019by Inyo Visitor

How can I be sure that this device (Goldline AQL-WW-P-4) will be compatible with my system? I have a Aqua Plus system that was installed in 2010, however the logic board was replaced in July of 2016 (Hayward GLX-PCB-PRO Main PCB). I understand that there may compatibility issues with different versions.
 Reply

A  Answered on 3/27/2019 by InyoPools Product Specialist Lennox H.

Hi. This Wired Wall Mount - AQL-WW-P4 is compatible with your controller. You will not have any issue unlike some wireless version options. 
 Reply


?     Asked on 4/30/2019by Jim

I just had the aqua plus system installed last year. The software version is 4.46. Will this work for my system?
 Reply

A  Answered on 5/1/2019 by InyoPools Product Specialist Lennox H.

Hi, Jim. Yes, this P-4 Wired Wall Mount Controller - AQL-WW-P4 is compatible with the AquaPlus controller. 
 Reply


?     Asked on 5/15/2019by Patrick

My wired remote is dead, no power or lights on. Panel works perfectly. Tried a new remote but that didn't help, still dead. Any idea what the solution would be to fix?
 Reply

A  Answered on 5/20/2019 by InyoPools Product Specialist Lennox H.

Hi, Patrick. If replacing the remote did not work, the issue could be the wires or the terminal on the PCB.  
 Reply