I have an AquaRite which is 5 Years old and think my software is different then the new cell requires. Which cell do I need?
Reply
If you have an older unit (older than 2009) than you would require the GLXCELL15W which you may view or purchase here http://www.inyopools.com/Products/02100002048034.htm
Reply
How do you determine if the power supply has software revision 1.50 or higher?
Reply
Hi Ted. On your controller you will press the "Diagnostic" 7 times to get to the Software revision level, that will tell you the revision software level of your unit.
Reply
My cell is Turbo-cell T-cell-5 3A1004-1035678 AQUA collection. My unit is Goldline
AQ-TROL-RJ-CUL. Which cell do i use to replace my cell ?
Reply
Hi, MichaelPlease be advised that you would need to check in your diagnostics on your control panel to verify that it's inner changeable. If your board is more then 7 years old it will not be and you will have to stay with the same cell you have. Here is a link to the T-cell-5 cell. http://www.inyopools.com/Products/02100000039322.htm?Keywords=t-cell-5
Reply
Is the T-Cell-15 compatible my board, if I purchased the Aquarite 15K - AQR3?
Reply
Any of the t-cells will go with the control board, you just need to make sure after installing the cell that you set your control board to the t-cell that you installed. So if you install the T15 you would set your board to T15.
Reply
I have a GLX PCB board, the number on it is G1-011056-1 and, when I check the diagnostic board, I get a reading of 2.60. Will this board support a T-3 cell? Thanks for the help.
Reply
Hi, Christopher. Yes, if the revision number is 2.60 then it will be compatible with TCELL3.
Reply
I replaced the board in 2014 G1-011056G-1A GLC 13280 0900003-159-01/4213. Will this accommodate the T-3 cell This is an inground pool 11000 gallons capacity
Reply
Hi, Lee. That board will be able to accommodate the TCELL3.
Reply
I have a Goldline Turbocell 9 that I suspect is not working.
My board is a PL-PS -8 (*3LO806 -1024841*) Main software revision 2.86
The board does not offer the Turbocell 9 as an option so I have selected 15 and it has been working fine until now.
WHat cell do I need?
Thanks
Reply
The cell you can use would be Aquarite Replacement Cell (TCELL15) - GLXCELL15 or Aqua Rite Salt Cell Replacement T-15 (2 Year Warranty) - PL7106.
Reply
My Aqua Rite is reading my salt level at 600 and when we attempted to recalibrate it only changed to -300 before jumping to 600 and then the check salt level and check salt generator light flashed on. Should I assume that my T-3 cell needs to be replaced? It is less than 3 years old and we haven’t had a huge amount of build up in it at all. Thanks for your help.
Reply
Hi, Delene. If your Cell Voltage and Cell Amps are within the correct range, then the cell is bad and will need to be replaced.
Reply
My T-3 aquarite is reading the salt too low. Pinch-a-Penny tests salt at 3400 and aquarite at 2000. I also took the cell to P-A-P and they said it is still working. I have recalibrated and it only lasts for a couple hours. One other thing that is malfunctioning is when I go to the option to turn the dial to adjust chlorine output, then I turn the dial, the setting doesn't change until I get the dial very close to zero and then it jumps all over the place. Any suggeestions?
Reply
Hello, Have you tried cleaning the cell with muriatic acid? If you have, we recommend bringing the cell up to your local Pinch a penny and have them test the cell. If the cell is good, then you would need to change the main PCB board.
Reply
I just had a AquaRite 15K installed 3 days ago. I just took my water to Pinch-a-Penny to get tested and the salt reading came in at 2450 and they recommended 1 bag of salt but my system is reading 3100 of salt. What would be causing this?
Reply
You may need to allow another day or two for the salt to completely dissolve if it was just added and or, you may need to recalibrate the system. Please check out our How To Recalibrate the Salt Level on a Hayward Aqua Rite guide.
Reply
I have a Tcell 5 aquatrol salt gen cannot find on your sight
Reply
Hello, Here is a break down of your salt system.http://www.inyopools.com/parts_hayward_goldline_aqua_trol.aspxWhich part were you looking for?
Reply
Are gaskets required for connecting the ends of the salt cells? Mine has none and a slight leak.
Reply
I think my pool is about 14000 gallons, most pool guys also estimate the same. Question is it a good idea to size the salt generator to the size of the pool? In other words bigger is not better? I am using the hayward t3...
Reply
Hi, Robert. Bigger is better when it comes to sizing chlorine generators.
Reply
What replacement options do I have for Hayward t9
Hi, Mark. You can use either the W3T-CELL-9 or W3T-CELL-15 based on your controller and the PCB software revision.
Reply
What options do I have for replacing the Saltwater Cell for this system? The pool is 24' by 52".
Hi, You will need this Aqua Trol T-CELL-5 Replacement Salt Cell for the salt system shown in your photo.
Reply
I want to make sure I purchase the correct T-CELL-3 for my system. I have a hayward Pro Logic PL-P-4 system. Do I need the W3T-Cell-3 or the T-Cell-3? I don't understand the differnce?
Reply
Hi Charlie, the W3TCELL3 is the same as the TCELL3. The 'W3" is just the online retail part number.
Reply
my pool is 10600 gallons and I have this cell can I replaced it with this one AquaRite 15 K replacement cell - W3T-cell-3
Hi Carlos, Since you have a T-Cell-15 cell you would require this AquaRite Replacement Cell (TCELL15) - W3T-CELL-15
Reply
I have a Hayward T Cell 3 salt cell. Can I replace it with a Hayward W3 T Cell 3? Are they compatible?
Hello, yes this cell is a replacement for the TCELL3. The 'W3" in front of the part number just represents the online retail part number.
Reply
Will this cell work with an older prologic system that controls a very small pool ?
Reply
The W3T-CELL-3 will work with ProLogic systems with firmware 4.1 or later. You can scroll through the ProLogic menu to find the firmware revision.
Reply
My current salt chlorinator is a Hayward SwimPure Plus Turbo Cell. Will the AquaRite 15K Replacement cell? My board is an AquaRite Electronic Chlorine Generator/ Goldline Controls.
Reply
Hi Pat, There should be some part #'s on your cell like GLXCELL15, TCELL15, GLXCELL9, TCELL9, etc.. Could you please provide us with the model # from your cell. Simply click the reply link below to supply this information and then we can make the proper reccomendation.
Reply
I have an aquarite goldline with a t15 cell. I saw your video where I can use a t-3 and up with revision 1.5. I have a revision 1.59. Am I good to buy the T3. I have a 10000 gallon pool.
Reply
Yes, you can use the T3 (W3T-CELL-3) if you have the 1.59 revision. You'll need to change the cell selection on your Aquarite control panel. Click Here to View Instructions on Changing the Cell Type
Reply
I Have an older Aqua Rite 20 system with a t-cell 5. Will this one be compatable, I can't seem to find a T-cell 5 replacement.
Reply
Hello John. The AquaTrol & AquaRite 20K Replacement Cell Only - No Unions - W3GLX-CELL-5 is a compatible replacement for the T CELL-5. Attached please find the Hayward Quick Reference Guide Please note Section - Change Cell Size. Following the stated procedure will determine if your Aqua Rite is capable of accommodating a different Cell Size (larger or smaller capacity) than the original T CELL -5.
Reply
I have a Hayward TurboCell 925 for an 11,000 gal pool. It has failed. Is this a compatible replacement?
Reply
Hi Danny, your TurboCell 925 is an extended life version of the T9 salt cells, so you would need the Hayward AquaRite Replacement T-CELL-9, 25,000 Gal Pool, TurboCell, Model W3T-CELL-9 or the Pureline Replacement Salt Cell, Compatible with AquaRite® T-9® (2 Year Warranty) - PL7105 to replace it. Be sure to review the T9 Cell Installation Guide for some helpful tips.
Reply
