What is the voltage on this unit? How long is the manufactures warranty? If the system requires repairs during warranty, what do I do?
Reply
This pump runs on 115V power. This unit comes with a 1 year manufacturer's warranty. If the pump needed repair, you would call Hayward directly and they would put you in touch with a warranty service station in your area.
Reply
How many hours per day should I run my pump?
Reply
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Reply
I changed the impeller gasket but the pump still leaks in back of motor did I miss maybe a gasket some where
Reply
Hi Paul, Did you replace the shaft seal as the shaft seal is biggest culprit for leaking.
Reply
I have a Hayward Matrix 1 H.P. pump & I'm curious if a 3 way diverter valve will work on above ground pools for cleaning/ by passing the filter...if so how would it be installed ??
Reply
June, A 3-Way can be installed for cleaning/ bypassing the filter, you'll have to install the valve on the discharge side of the pump before the filter.
Reply
What is the warranty?
Reply
Hi Mark, the Hayward Matrix pump has a 1 year warranty. I also like the PureLine Pure Pro XL Pump which also has a 1 year warranty.
Reply
The strainer on this pump has a lid which has three slots to open it up. Where can I buy a tool to do this?
Reply
I am not aware of a tool for the pump, I recommend giving Hayward a call, 1-800-657-2287, to see if they make one for that pump.
Reply
How to change horizontal/vertical discharge feature
Reply
Hi, Frank. Step by Step instructions are available in our How To Rotate the discharge port on your Hayward Matrix Pump guide.
Reply
how do I remove the pump housing from the motor ?
Reply
Attached is a how-to guide that will help you.
Reply
can the pump housing be changed too be on the side instead of on the top
Reply
Hi. Yes, the discharge can be rotated, step by step instructions are available in our How To Rotate the discharge port on your Hayward Matrix Pump guide.
Reply
How to change Haywood Matrix Pool pump from a top mount discharge to a side mount discharge?
Reply
Hi, John. Step by Step instructions is available in our How To Rotate the discharge port on your Hayward Matrix Pump guide.
Reply
I need a new pump, I have added a solar heater with 22 1'x12' panels that is on opposite side of house of pool and have a Jacuzzi Laser II 192 sand filter, was wondering if the 1 hp model is good or should I go with the 1.5 hp model, and could I use the 1.5 hp pump with this filter, pool is 15x24 if you need to know.
Reply
This pump would be to small for this . Do you know what type of solar panels you have and what size the plumbing is. That way we can determine what the flow should be
Reply
This pump would be to small for this . Do you know what type of solar panels you have and what size the plumbing is. That way we can determine what the flow should be
Reply
Besides being able to easily rotate the discharge port, what is the difference between the matrix and power-flo II pump.
Reply
Hi, Ryan. The PowerFlo Matrix Pump is a higher performing pump than the Power-Flo II pump which is normally used when high flow is required.
Reply
can this pump be used on a in ground 16x32 pool
Reply
Can I purchase only the motor for this unit?
Reply
Hi, Douglas. The replacement motor is P/N SPX1510Z1XE.
Reply
What is the difference between the sp1592 and w3sp1592?
Reply
Hi Cesar this is the exact same pump. The W3 part # designates that the pump was purchased online. If you purchase the Non W3 part # from an online store then the manufacturer warranty will not be in place.
Reply
I have difficult taking off the cover of the pump cover after it gets dirty.............
Reply
Hi Richard, Sometimes you may need to lubricate the lid gasket/ o ring using Magic Lube that will aid in the removal and sealing of it in the future.
Reply
What is the gallons per minute flow rate for the hayward power flo-matrix 1 hp pump model # sp1592 ?
Reply
Hi Tom, so that will depend on the feet of head however if you look at the performance data chart in the product details on this page the flow rates will be listed.
Reply
What is the pump flow rate?
Reply
Hi, The flow rate of this pump is base on the Total Dynamic Head (TDH) of the pool. The performance data which included the flow rate is available in the Product Description.
Reply