?     Asked on 4/1/2007by Guest

Do you have a schematic for this Hayward filter control valve and also do you have replacement parts such as the spider gasket?
 Reply

A  Answered on 4/1/2007 by InyoPools Product Specialist Patrick P.

Here is the schematic for this valve http://www.optimusparts.com/onlinecatalog2006/sec_e/e-10.pdf You may purchase any of these parts by going to http://www.inyopools.com and entering our part # in the search by keyword box located on the top left hand corner of the website.
 Reply


?     Asked on 1/31/2012by Guest

I need parts for my filter valve. When I look at the filter parts breakdown, it gives me different choices. How do I know which one is the one I need?
 Reply

A  Answered on 1/31/2012 by InyoPools Product Specialist Patrick P.

In order to locate the correct parts we will need to know the model number of the filter valve. Two identical filters can have two different valves. Typically the valve model will be located on the label of the valve. If there is no model number on the valve, you can try to see if there are any part numbers on the valve itself. Once you've located you valve model you can check out our >Filter Valve Parts.
 Reply


?     Asked on 4/13/2015by Dan

Will this valve replace a push pull valve on a Hayward DE4800L? The center distance on the ports attached to the filter is 5". Or would you suggest just replacing the push pull valve I have now?
 Reply

A  Answered on 4/13/2015 by InyoPools Product Specialist Robert M.

Hello Dan - The SP0740DE will work with the DE4800 series.
 Reply


?     Asked on 12/20/2017by Mike

Will this valve work on a Hayward Swimclear Multi-Element C3030 cartridge filter?
 Reply

A  Answered on 12/20/2017 by InyoPools Product Specialist Lennox H.

Hi, Mike. This Selectra-Flo Valve is not compatible with the Hayward Swimclear filter - C3030. 
 Reply


?     Asked on 6/26/2018by Jack Wyatt

Do you have a video or instructions for replacing a Hayward SPO740DE on a Hayward DE3620 ProGrid Vertical DE filter system? This is new equipment for existing plumbing.
 Reply

A  Answered on 6/26/2018 by InyoPools Product Specialist Lennox H.

Hi, Jack. We do not have a video or instructions. You can reference the Vari-Flo Owner's Manual Model: SP0740DE, and the Pro-Grid D.E. Filter Series Owner's Manual for installation instructions. 
 Reply


?     Asked on 6/5/2019by spectra builder

is the hayward sp740de and sp0740de interchangeable, can i replace the sp740de with the sp0740de?
 Reply

A  Answered on 6/6/2019 by InyoPools Product Specialist Hector F.

Yes this is essentially the same valve with just an alternate part number.
 Reply


?     Asked on 10/16/2019by mike

will this part fit exactly into the body of my backwash valve bodl sp740de
 Reply

A  Answered on 10/17/2019 by InyoPools Product Specialist Hector F.

Yes, this valve both uses the same parts and also completely replaces the model sp740de valve. 
 Reply


?     Asked on 12/29/2019by TahitiPool

Hello, I have a ProGrid DE6020 with this valve SP740DE but there is no Rinse option on this valve. How can I make a Rinse after using the Backwash mode of the valve ? Thank you for your help Julien
 Reply

A  Answered on 12/30/2019 by InyoPools Product Specialist Lennox H.

Hi, TahitiPool. Using this valve you will Backwash the filter, then place it back in Filter Mode. Rinse is not required since this valve has a limited options. 
 Reply

  • Commented on 12/30/2019 by Product Owner

    thank you for your answer. The problem is that a little bit of dirt comes into the pool after the Backwash with no Rinse. Do you think i can drain the soiled water of the filter with the air valve on the top of the filter in order to do a Rinse ?
     Reply

    • Commented on 1/16/2020 by InyoPools Product Specialist Lennox H.

      You can place the valve is the Waste position for a short time to eliminate any dirt or debris from going into the pool. 
       Reply


?     Asked on 10/20/2021by Dan

I have an older Hayward 200 sand filter, not DE, and need the entire selector assembly for it. My assembly looks like the one for the DE model Hayward Selecta-Flo Multiport Valve - SP740DE. will the DE work on mine?
 Reply

A  Answered on 10/21/2021 by InyoPools Product Specialist Megan C.

I am not sure what model 200 you have by Hayward, however, the S200  https://www.inyopools.com/Products/02200011071937.htm?Keywords=hayward+s200 is pretty popular. If that is your model, the Multiport Valve 1.5" for Hayward S200 Sand Filter - SP0710X32 https://www.inyopools.com/Products/02201266001085.htm is the correct valve. You are welcome to upload images of your filter and the image of the top of the valve and we will help identify it. The valve you mentioned cannot be used with sand filters. 
 Reply