What is the difference between an Electronic and Millivolt ignition?
Reply
The basic answer is that Millivolt is the old style of ignition, using a standing pilot light. While the electronic ignition uses a spark start system like a gas grill. Electronic ignitions are more efficient in gas usage and also are better suited for high wind areas where a pilot light might get extinguished.
Reply
Where can my heater be installed?
Reply
There are specific venting requirements and clearance distances that must be met to ensure proper operation. Consult the owner’s manual for exact specifications for your model of heater.NOTE: Gas fired heaters should be diagnosed and repaired by trained personnel.
Reply
Can you use the H100ID1 Hayward pool heater on a salt water pool?
Reply
The H100ID1 can be used on a salt water pool. However, we would recommend a unit with a cupro-nickel heat exchanger. The cupro-nickel heat exchanger is much more durable than the copper exchanger used in the H100ID1. The H150FDN has a cupro-nickel exchanger and would be better suited for salt water.
Reply
Does this heater hook up to a normal sized pool hose or do I need to buy adapters to change size?
Reply
This heater now has 2" couplings for the piping. If your pool piping has 1 1/2" piping, you will need to buy 2" to 1 1/2" adapters.
Reply
What size pool will this heat? I have a 18 x 33 above ground.
Reply
Your selection of heater size depends on many factors but primarily on how fast you want to heat your pool. This 100,000 BTU heater would raise the temperature of your 15,000 gallon pool roughly 3/4 degree per hour.
Reply
does Hayward make a propane adapter for this heater
Reply
Fran, The conversion kit from Natural gas to propane for this heater is part # 6223-79
Reply
Can a propane heater be converted to natural gas?
Reply
Yes the Hayward H100ID1 can be converted to natural gas by using the Hayward H100 Propane to Natural Gas Conversion Kit.
Reply
My heater will not click on in the morning. I turn the on-off switch OFF at night. Should I leave it in the on position and just turn down the heat button all the way.
Reply
Hi, It's better to use the On/Off Switch when the heater is not being used. You will have to investigate the cause of why the heater is not turning on. The Hayward Heaters Above Ground Manual has a few troubleshoot tips you can try.
Reply
Can I use an additional pool pump to run this type of heater ( separate from the filter pump)
Reply
Hi, You can but it will be pointless because you will need to add another filtration system to filter the water going into the heater.
Reply
I have been told by dealers not to heat my pool because the internal components deteriorate quickly, within a year to year and a a half, if the water Ph and chlorine levels are not perfect 24/7. Is there any validity to this?
Reply
That is true for saltwater pools. For saltwater pools, I recommend a heater with a cupro-nickel heat exchanger which extremely retards the corrosion factor. With chlorine pools a heater with a regular heat exchanger will last, just depends on amount of use.
Reply
Which pool heater will be ideal for use with salt water?
Reply
Hello Manny- For salt water pool applications we highly recommend getting a Cupro-Nickel unit. The Cupro-Nickel heat echangers can take more abuse from minerals than the standard copper tubes. Here is a link to the Hayward units that are Cupro-Nickel. http://www.inyopools.com/heaters_hayward_lownox.aspx
Reply
Any reason this can not be used with a 9000 gallon Viking in ground fiberglass pool? Listed as an above ground heater.
Reply
You could use that heater, probably will not be too efficient, but you could use it. If you are wanting a natural gas heater I would recommend at least the H150FDN. For a pool, it will be most efficient to get a heat pump, part number HP21004T.
Reply
i have a Hayward heater 100,000 btu heater and 10x18 pool. How many hours will I have to run it to heat to 82 degrees
Reply
Hi. You can expect a 1.9 degree temperature increase an hour using this heater to heat a 10'x18' pool.
Reply
does a red blinking lite on the ignition module mean its bad ? H100ID
Reply
Luis, I was unable to locate a trouble shooting guide for this heater. I would recommend calling Hayward at 888-429-9273. They will be able to assist you.
Reply
I have this heater in my new semi inground pool. Heater and filter are surrounded by fence and top has mesh, but floats are on top of mesh almost enclosing it. Is this okay for gas exhaust? Its a little stinky when i go in, but still definitely airy and in no way considered totally closed in.
Reply
Hi, Mark S. Unfortunately, that is not okay. This unit requires an unobstructed clearance at the top for ventilation purpose.
Reply
What does the water pressure Switch pressure have to be we cant get heater to start, We were told the is no water going through heater pressure sitch, But when tech held switch oen pump fired.
Hearyer Model H100Id1
Reply
Hi, Jeff. The water pressure switch is activated with a flow rate of 20 - 70 GPM's.
Reply
Purchased H100Id1 gas heater, works great but sound like a small tea kettle whistling when burner kicks in. low water flow is not the issue.
Reply
Hi, J. You may have air in your gas line or have low gas pressure.
Reply
We have 24 foot circular pool 52 deep. What size or model do we need. What’s most efficient and less costly to run. Do I still run pump with this ?
Reply
Are there any restrictions on using this heater in California?
Reply
Hi, Ray. The South Coast Air Quality Management District ( SCAQMD) Area of Jurisdiction REQUIRES a Low Nox Heater be installed. The following 6 California Counties are affected: Los Angeles, San Bernardino, Ventura, Orange, Riverside, & Kern. Installing a non-compliant heater in these counties will void the manufacturer's warranty and could result in a fine from your local code enforcement. This unit is not compliant if you're located in one of these counties.
Reply
Interested in the 120v electric heater.
A) can it heat a 5k gallon brick bath spa
B) Does this have a temp controlled timer automatic
C) Can this be used for an inside pool heater and machine left inside
Reply
Hi, Ricky. This heater can heat a 5k gallon brick bath spa, is equipped with a thermostat; however, cannot be installed indoors. The Universal H-Series Low NOx Heater 150K BTU - NG - H150FDN will meet all your requirement. You will also need the Indoor Vent Kit
Reply
I have a Hayward 100d heater when I turn on the heat it starts making a clanging noise what is the problem?
Reply
Hello, We recommend contacting the manufacturer on that question. You can reach them at 908-355-7995.
Reply
IS THIS ELECTRIC OR GAS IM LOOKING FOR AN ELECTRIC HEATER
Reply
Hello,This is a natural gas heater. If you are looking for a heat pump, please see here.
Reply
I bought a H100DI 2 weeks ago and it was installed for me as an exact replacement to an old one for my spa. It does not work. Who should I call to fix the problem? it is under warranty and I need to know who should I call to fix it. I live in Canton MA zip 02021
Reply
Hi, Mo. You will need to contact the place of purchase or Hayward Product Support to initiate a warranty claim.
Reply