How do you delete old programs for the filter pump?
Reply
All Button Controller. Pressing the reset switch, located on the left side, will momentarily display the software part numbers and revision letters for both the controller's micro controller chip and the power center's fi rmware chip. The reset switch also resets the micro controller, but does not remove any programming, AUX labels, etc. 2. OneTouch Controller. The reset switch can be used to show the revision code for the fi rmware for both the controller's micro controller chip and the power center's fi rmware chip.
Reply
How do I reset the start and stop time of the pool going on
Reply
Hi Elaine, You can find the instructions on page 10 of the Jandy Controls All Button Owners Manual.
Reply
How do I program spa remote functions such as booster, air, etc?
Reply
Hi Tim, You can find programming instructions in the Aqualink RS All Button Control System Owner's Manual.
Reply
how do you delete pool heater programs?
Reply
Hi, You can find the instructions on page 21 of the Jandy Controls All Button Owners Manual.
Reply
Rs8 aqualink
How do you cancel a program step by step
Reply
Hello, Please refer to page 21 of the owner's manual: http://www.inyopools.com/manuals/259/jandy_controls_all_button.pdf
Reply
I cannot get my spa to operate, the lights are on heat and spa more the over spill keep running.
Reply
Hi, Victor. It sound like it could be a bad relay, I would recommend having a tech inspect the unit just to be sure.
Reply
How do you set time on and time off for the pool.
Reply
Hi Victor, Page 10 of this Jandy AquaLink Owner's Manual explains this in detail.
Reply
I am looking for an owners manual that will tell me how to clear and reprogram all times, temperatures ,etc. I have already printed the troubleshooting manual
Reply
I have provided the link to the Jandy AquaLink RS All Button and One Touch Control Systems Installation Manual. This manual will provide you with the directions you seek. If you feel you need further assistance, you may contact the manufacturer Jandy, at 1.800.227.1442https://www.jandy.com/~/media/zodiac/global/downloads/0748-91071/6594.pdf
Reply
How do I increase the heat temp for the pool?
Reply
Hi, Becky. Instruction are available on page 8 and 11 of the Jandy Controls All Button Owners Manual.
Reply
my rs 8 says 6700 rev c. all lights are red and it doesn't respond
Reply
D, we apologize for the inconvenience, however, our technicians are not certified by Jandy to provide technical advice on the Jandy Jandy Aqualink RS8 Pool/Spa Combo Control System. We suggest contacting the manufacturer directly and speaking to their technicians. Jandy/Zodiac can be reached by calling 800.822.7933.
Reply
I am a first time user of the Aqualink RS8. Right now I simply need to know how to drain the spa (clean it) and refill it. PLEASE can someone help. Phone call would be best 951-760-8688 Thank you
Reply
Gail, we apologize for the inconvenience, however, we have been unable to obtain an answer to this question from the manufacturer. We suggest calling Jandy directly to see if they might be able to offer any advice.
Reply
How do you turn the Heater Program off
Reply
Bruce, the instructions are available on page 8 and 11 of the Jandy Controls All Button Owners Manual for the Jandy Jandy Aqualink RS8 Pool/Spa Combo Control System.
Reply
How to slow down light colour changes
Reply
Hi. You will need to select a different light show. We will need to know the make and model of the pool light or use the Light Button, turn the fixture On/Off/On.
Reply
HOW DO YOU EMPTY THE SPA
Reply
Hello, no two automation systems are the same but ideally, for just draining a spillover spa you will need to use the valve actuator that controls the spa main drain to open it while the pump is on using the actuator toggle switch locating on the side of it.
Reply
How do I change the temperature to turn on FREEZE PROTECTION. Where I live we have many nights that go down to 33 - 40. I am wasting a lot of electricity.
Please respond via email to the email above.
Reply
Hello Steve, please review Freeze Protection Menu page 16. You can change the temperature at which freeze protection will activate (between 34ºF and 42ºF). For example, if you want freeze-protected equipment to turn on when the air temperature has dropped to 37ºF, you can set the system so this is the case..
Reply
What does it mean when the panel reads air sensor open
Reply
You may simply just need to clean the connector on the board? You could just have a corroded connector. If after trying that and it doesn't work you may need to replace the sensor.
Reply
