?     Asked on 7/11/2015by Greg

Flow keeper valve goes down on the cleaner in the pool? or up in the skimmer? Also, which end is up when installed? I bought a used Zodiac Beta with no instructions and don't want to wonder why it won't work if I install it wrong. Thank you Greg
 Reply

A  Answered on 7/14/2015 by InyoPools Product Specialist Lennox H.

Hi Greg, Side the has the window (longer end) goes down into the skimmer.
 Reply


?     Asked on 7/30/2015by barb

Where can I find a spring for the flow keeper valve. W60050
 Reply

A  Answered on 7/30/2015 by InyoPools Product Specialist Andy O.

Barb- Unfortunately, you would have to buy the entire flow keeper valve. They do not sell individual parts for those.
 Reply


?     Asked on 10/4/2015by MA

Between 1 & 3 what's the strongest setting, I would think 3.
 Reply

A  Answered on 10/5/2015 by InyoPools Product Specialist Joe S.

The 3 setting will be the stronger of the the two
 Reply


?     Asked on 4/8/2016by Sharon Smith

Will this work on original barracuda device?
 Reply

A  Answered on 4/9/2016 by InyoPools Product Specialist Lennox H.

Hi Sharon, This Flowkeeper Valve can be used with almost all Barracuda pool cleaner.
 Reply


?     Asked on 12/27/2016by rene

why my barracuda vacuum stop w/c I clean my filter 2 mos ago, when I used the skimmer run smoothly you can tell by the flow of the water.
 Reply

A  Answered on 12/28/2016 by InyoPools Product Specialist Adam Y.

Good morning Rene, Do you have suction on the skimmer? If so it could be that the diaphram inside the cleaner is stretched or has a hole in it. We do sell the diaphram but I would check to see if this is your problem. If so, You can find that part by typing Barracuda parts in our search bar.
 Reply


?     Asked on 4/27/2017by Hil

I bought a new flowkeeper a few months ago. I didn't have any problems with it for approx. five or six months. A few days ago I took it out because I had to pour some stabilizer through the skimmer which I had done before on several occasions. Ever since, as soon as I insert the flowkeeper the pump pressure goes down and the barracuda is not working. What could be wrong? The flowkeeper looks perfect.
 Reply

A  Answered on 4/28/2017 by InyoPools Product Specialist Scott W.

I feel like there is a blockage in your plumbing causing a reduction in suction. I recommend Purge which is manufactured by Natural Chemistry and will clear your pipes allowing for a stronger flow.
 Reply


?     Asked on 7/5/2018by Tina

One of the springs broke on my Flowkeeper, is there anywhere I can just by the replacement spring?
 Reply

A  Answered on 7/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Tina. Unfortunately, the spring only is not sold as a replacement part. 
 Reply


?     Asked on 9/5/2018by Michael

What is the purpose of the red tab thing on the flowkeeper?
 Reply

A  Answered on 9/5/2018 by InyoPools Product Specialist Megan C.

Hi, Michael. The red tab is used to keep the valve open.
 Reply

  • Commented on 5/23/2020 by Product Owner

    The red tab is missing off of the valve. Is this part necessary to run right.? It’s running very slow. If so, can I buy red tab? Thanks for your time.
     Reply


?     Asked on 9/13/2018by Stephen Tremblay

I had my G3 out of the pool for a month and when I went to put it back online it would not run and I noticed the flow keeper would open up, does not matter if the hose to the cleaner is connected or not. What could cause this and do flow keepers go bad?
 Reply

A  Answered on 9/15/2018 by InyoPools Product Specialist Lennox H.

Hi, Stephen. A flow keeper can go bad if parts are broken, primarily the springs or the red tap. 
 Reply


?     Asked on 10/9/2018by David Johnson

my flowkeeper valve keeps opening up as soon as I turn on the pool pump. what can I do the barracuda mx8 will not move with the valve open.
 Reply

A  Answered on 10/10/2018 by InyoPools Product Specialist Andy O.

Hello David- The Flowkeeper Valve (w60050) part number 3237-130 can be adjusted by moving the bottom piece that onnects with the spring to ther 2 or 3 position. I would suggest moving it to a higher tension to see if that helps.
 Reply


?     Asked on 10/10/2018by David Johnson

how can you tell if the flowkeeper valve is bad. what will it be doing.
 Reply

A  Answered on 10/10/2018 by InyoPools Product Specialist Hector F.

If the springs on the valve have gone bad,(in example corrosion), the plastic has broken allowing unwanted water flow into it, or if the valve is not staying in the position that you set it at then it may be time to replace it. 
 Reply


?     Asked on 6/16/2019by joe harcut

which way is the arrow on the flowkeeper valve is to be pointing up or down
 Reply

A  Answered on 7/24/2019 by InyoPools Product Specialist Hector F.

The corrugated side of the valve needs to be facing up connected to the cleaner hose. 
 Reply


?     Asked on 8/28/2019by wboston

purpose of Zodiac g4 flowkeeper valve
 Reply

A  Answered on 8/29/2019 by InyoPools Product Specialist Lennox H.

Hi, Wboston. The Flowkeeper Valve regulates flow to ensure the pool pump and cleaner run properly.
 Reply


?     Asked on 10/5/2019by Travis

Does this work on the mx6?
 Reply

A  Answered on 10/6/2019 by InyoPools Product Specialist Lennox H.

Hi, Travis. Yes, this Flowkeeper Valve - W60050 can be used with the Baracuda MX6 Cleaner.
 Reply


?     Asked on 3/25/2020by Mildred Tomisman

Which side should be facing the top of the pool? Where is the flow adjustment located?
 Reply

A  Answered on 3/25/2020 by InyoPools Product Specialist Lennox H.

Hi, Mildred. Reference to Step 12 of the How To Set Operate the Zodiac X7 Cleaner Through a Skimmer Guide. 
 Reply


?     Asked on 8/1/2020by Ron

If I order flowkeeper valve today what is shipping time.?Also is this new part or reconditioned? Thank you.
 Reply

A  Answered on 12/11/2020 by InyoPools Product Specialist Hector F.

Hi Ron, this part is brand new and currently has an approximate delivery lead time of 2-6 business days. 
 Reply


?     Asked on 2/16/2021by Frank

My flow keeper valve pops out of the skimmer hole after I turn the pump off every time. What is my problem?
 Reply

A  Answered on 2/17/2021 by InyoPools Product Specialist Hector F.

Hi Frank, I would suggest using a rubber 45-degree elbow that will help to keep that valve positioned in the skimmer suction hole. 
 Reply