?     Asked on 10/13/2014by Guest

I've just replaced my housing gasket because I had quite a water leak. The new gasket also leaks. Is there one way the gasket should go on? Or is there something else that could be causing the leak? Water is coming out at a pretty good clip.
 Reply

A  Answered on 10/13/2014 by InyoPools Product Specialist Patrick P.

Have you checked the shaft seal yet? The shaft seal is located behind the impeller and if it leaks it will come from the union where the motor bolts to the pump. Shaft seals depend on the pump model.
 Reply


?     Asked on 9/4/2015by John

I have an older Challenger pump with 35-5188 diffuser. I need to find out how to tell whether I need a round o-ring or square o-ring for both the diffuser and the housing. I ordered the GO-KIT5 that contains both round o-rings. The pump has been serviced multiple times by various people and not sure if round is correct versus square….I have found both types in the used parts box. Thanks
 Reply

A  Answered on 9/9/2015 by InyoPools Product Specialist Lennox H.

Hi John, The Diffuser (35-5188) is used on the Pentair Challenger High Pressure Pumps. The round o-rings not the gaskets are used with the high pressure pumps.
 Reply


?     Asked on 6/23/2016by Frankie

procedure for replacing housing gasket 355329
 Reply

A  Answered on 6/24/2016 by InyoPools Product Specialist Alan M.

Unscrew the clamp holding both halves of the pump together. Remove the old gasket. Lubricate and install the new gasket. Reattach both halves of the pump and tighten with the clamp.
 Reply


?     Asked on 7/17/2017by John

Does the Gasket housing 35-5329 have a round or square profile. I recently installed a new motor on my Challenger pump and used the Gokit5, but the round gasket in the kit didn't work and I need the square gasket. Thanks
 Reply

A  Answered on 7/20/2017 by InyoPools Product Specialist Lennox H.

Hi, John. This Housing Gasket - 355329 is squared. 
 Reply


?     Asked on 5/2/2018by Chris

The gasket is not square, so my question is does the longer edge get installed against the front housing or the short? It does not seem to fit 100% tightly with the thinner edge, but also does not seem to fit perfectly the other way either. The one that came off the pump was the square cut one as well, but I am wondering if even that one was the correct one...
 Reply

A  Answered on 5/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Chris. The short side of this gasket is placed against the volute. It will seal once the two halves compresses the longer side of the gasket. 
 Reply


?     Asked on 3/23/2019by Wayne

I have a PAC-FAB Challenger 2HP Frame: Y56Y Pump Housing: Part #: 35-5460 1081 Pool Pump duty mount horizontal with vent holes down It is leaking between the seal plate and the front housing. The water is coming out the top, right around the clamp band. I think I just need a new O-ring, but I suspect I will need to replace other seals if I take the pump apart. What parts will I need to do this job right?

 Reply

A  Answered on 3/30/2019 by InyoPools Product Specialist Lennox H.

Hi, Wayne. You will be better off getting the Tune Up Kit - GOKIT5 like you did a few years ago. 
 Reply

  • Commented on 5/4/2019 by Product Owner

    I have the same problem now that I did a couple of years ago. The kit does not have the O-ring that seals the pump housing to the strainer basket (i.e. where I have the leak). the kit has everything but that. And I made the same mistake again. I took the pump apart before I looked at the kit closely. I need the square O-ring. Not happy. Mostly with me. Will try to get it locally.

     Reply


?     Asked on 3/27/2020by Greg

The motor on my system went out, my system is a Challenger High Performance Pump. I had it since 2004. My old motor model number is K63CXERW-4785, I ordered the replacement motor, part # B2853. I need a new impeller now, can I still use impeller part #355067 with my new motor? When I took apart the system, the housing that use the square gasket was the only gasket on it. Is there another gasket I need for the diffuser?
 Reply

A  Answered on 3/27/2020 by InyoPools Product Specialist Patrick P.

Hi Greg, Yes your 355067 Impeller will work on the B2853 motor. The only other part we suggest is a shaft seal. If you have a Challenger Pump then you will require this Challenger Shaft Seal.
 Reply

  • Commented on 3/29/2020 by Product Owner

    Thanks, will impeller part #355074 also work on my B2853 motor?
     Reply

    • Commented on 3/30/2020 by InyoPools Product Specialist Patrick P.

      Hi Greg, No the 355074 would not work on the B2853 as that impeller is too strong for the B2853 and would cause the B2853 to fail.
       Reply