?     Asked on 7/16/2016by Brian

is this a silacone gasket
 Reply

A  Answered on 7/16/2016 by InyoPools Product Specialist Lennox H.

Hi Brian, This gasket is not silicone, it's rubber.
 Reply


?     Asked on 7/16/2016by Brian

Do thay make this in a silacone gasket
 Reply

A  Answered on 7/20/2016 by InyoPools Product Specialist Lennox H.

Hi Brian, There is not a version of this gasket that is silicone.
 Reply


?     Asked on 7/31/2016by Wayne

My Anthony pool is 30 years old and was constructed with light fixtures made by WADE DESIGN INC, Model #15120. Is this the gasket for this light?
 Reply

A  Answered on 8/7/2016 by InyoPools Product Specialist Lennox H.

Hi Wayne, This gasket will fit the Anthony Pool Light fixture, however, I'm unable to confirm if this gasket will actually fit the model fixture you have.
 Reply


?     Asked on 4/19/2017by Gary A Banas

Is it wise to apply a silicone lube to the gasket ? If not silicone, is there a rubber lube that will work or is it better to just install dry ? Thanks.
 Reply

A  Answered on 4/19/2017 by InyoPools Product Specialist Lennox H.

Hi, Gary. Pool light gaskets do not require any lubricant it's installed dry.
 Reply


?     Asked on 5/5/2017by Bill

I have a Anthony pool ruffly about 40 years old, the light fixture outside ring measures 8in from the inside, is this the correct fit? I can't seem to find a product # on the fixture. Thanks.
 Reply

A  Answered on 5/5/2017 by InyoPools Product Specialist Lennox H.

Hi, Bill. This lens gasket is for an Anthony Pool Light, the diameter is 8-1/2 inches.
 Reply


?     Asked on 5/16/2017by Dan

the black gasket is slightly tapered. One side measures 5/8" thick, the other side measures 11/16". Which side goes out towards the pool (light lens) and which side goes towards the back of the light? Dan
 Reply

A  Answered on 5/20/2017 by InyoPools Product Specialist Lennox H.

Hi, Dan. If you're referring to the Dimensional Image, the 5-8" is the horizontal width of the lip and the 11/16" is the vertical width of the gasket. The gasket can be installed with either side towards the pool.
 Reply


?     Asked on 5/22/2017by Bill

I have a Anthony pool ruffly about 40 years old, the light fixture outside ring measures 8in from the inside, is this the correct fit? I can't seem to find a product # on the fixture. Thanks.
 Reply

A  Answered on 5/27/2017 by InyoPools Product Specialist Patrick P.

Hi Bill, This is the only Anthony light gasket we have shown that was used on Anthony lights so I think this should work for you. Here is a link to the Dimensions of the Anthony Pool Light Gasket
 Reply


?     Asked on 5/22/2017by Bill

I have a Anthony pool ruffly about 40 years old, the light fixture outside ring measures 8in from the inside, is this the correct fit? I can't seem to find a product # on the fixture. Thanks.
 Reply

A  Answered on 5/24/2017 by InyoPools Product Specialist Lennox H.

Hi, Bill. This is the correct lens gasket for the Anthony pool light fixture.
 Reply


?     Asked on 8/4/2017by Orrin Cross

My Anthony pool lite is marked Model No 20 with wet niche type. Also says Model No. -500 BC, use model CN5 fixture housing. Also it says use with model No. 21 or 19LA. Is the gasket you list (14118 Anthony) the correct one? It is about 40 years old. As long as I have it apart, should I replace the lamp (lighting fixture) as well? Thanks so much.
 Reply

A  Answered on 8/9/2017 by InyoPools Product Specialist Lennox H.

Hi, Orrin. This is the correct lens gasket for the Anthony light fixture that you have. 
 Reply


?     Asked on 7/9/2018by Larry

Looking for gasket. Light says for swimming pool-wet-niche type No. M- Model No. 30 Use with fixture housing model nos. 15 or 21 Lamp R40 - 120V -500W Max. - Do you sell the bulb to use?
 Reply

A  Answered on 7/12/2018 by InyoPools Product Specialist Andy O.

Hello Larry- Here is the parts breakdown I found for the Model # 30 light: http://www.inyopools.com/pool_parts_anthony_pool_light.aspx. The gasket would be Gasket, Light Lens (14118 Anthony) and the bulb 500W Flood R-40 6.56" MOL (5.0" Dia.) 120/130-Volt - NA706.
 Reply


?     Asked on 8/14/2019by Bruce

Hi looking for the gasket for the smaller Anthony light on my step and in my spa. I believe it's about a 4" Light since it looks about 1/2 the size of my large light.
 Reply

A  Answered on 8/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Bruce. I was unable to locate an Anthony spa light fixture. You will need to provide us with pictures of the fixture in order to identify it. 
 Reply


?     Asked on 7/10/2020by Craig

Need help IDing the model# for this old anthony lighting unit. Looking to upgrade to LED (if possible) and replace the gasket...also if possible. Any help would be great. Thanks

 Reply

A  Answered on 1/7/2021 by InyoPools Product Specialist Megan C.

If the outside diameter of this Anthony model measures 9-3/8" According to Hayward, their Universal Colorlogic LED light will fit your Anthony niche. They are currently only available in 12 volts. This means you'd have to add a transformer if your current light is 120 volt. Unfortunately, this product line is no longer available for Internet sale, please contact Hayward directly at (908) 355-7995 for a local dealer.
 Reply