?     Asked on 5/3/2015by richard

I need the oring that fits to this lid, any ideas?
 Reply

A  Answered on 5/4/2015 by InyoPools Product Specialist Matt S.

Hello Richard, I believe the lid you need is the Lid O-ring, 6" 5050-14A.
 Reply


?     Asked on 5/4/2015by Seth

I need the strainer housing but the only part # i can find is on the lid. Any idea how I can find out which housing I need as I see there are several different ones. My lid has the part #319-3260. Its a waterway pump by the way
 Reply

A  Answered on 5/5/2015 by InyoPools Product Specialist Lennox H.

Seth, This lid can be used on several different Waterway Pumps. If you can send us photos of the housing I can try to locate the correct housing.
 Reply


?     Asked on 6/3/2015by Inyo Visitor

How would i know if my trap is full? Will the water stop flowing into the pool.
 Reply

A  Answered on 6/4/2015 by InyoPools Product Specialist Brian M.

The water will definitely slow down, depending on how full you are talking about. It is better for the motor if water not flowing does not happen. It would put unneeded stress on it and possibility cause the motor to fail prematurely. If you see a decrease in the returning water, please empty the basket as soon as possible.
 Reply


?     Asked on 6/6/2015by Roy

This product is no longer available, is there a substitute?
 Reply

A  Answered on 6/6/2015 by InyoPools Product Specialist Patrick P.

Hi Roy, We researched this lid and found that the 319-3260 was replaced by the 319-4100 and this lid is a direct replacement. So we have re-activated this product and when placing an order we will ship the new 319-4100 lid which is shown in the photo on this page.
 Reply


?     Asked on 7/30/2015by Sue

We have the above ground hi flo pump it is a replacement for the original pump, We are having problems with when I connect the vacuum hose it sucks air. I googled the problem and found finally an answer that fits our issue. They said that the o ring in the filter basket/lid needed replacement and that fixed it. I see this replacement is made a bit sturdier than our lid. Does it also come with the o ring? we have been afraid the lid might break so I thought I should just get the whole lid in case
 Reply

A  Answered on 7/31/2015 by InyoPools Product Specialist Lennox H.

Hi Sue, The Waterway Hi-Flo Lid (319-3260) does not come with the Lid O-ring (5050-14A) it is sold separately. You can start with replacing the lid and o-ring to see if that will solve your problem.
 Reply


?     Asked on 11/2/2015by Ryan

Can you ship this item to the Philippines?
 Reply

A  Answered on 11/2/2015 by InyoPools Product Specialist Robert M.

Hello Ryan - We can ship this product to the Philippines.
 Reply


?     Asked on 5/9/2017by JW

I have not been able tofind any part numbers. Any suggestions
 Reply

A  Answered on 5/10/2017 by InyoPools Product Specialist Lennox H.

Hi, JW. You can send us photos of the pool pump and or the lid so that we can identify the pump.
 Reply


?     Asked on 5/22/2017by bill

hi I have a waterway pump serial # sd 130524 5429 and I need a clear lid for for the lid
 Reply

A  Answered on 5/25/2017 by InyoPools Product Specialist Lennox H.

Hi, Bill. We're unable to use a serial number to locate replacement parts only model or part numbers. This Lid - 319-3260 can be used on a dozen different Waterway pumps. If you can send us pictures of the pump we can confirm.
 Reply


?     Asked on 6/13/2017by Carole Joan Moore

We have a mustang 56 in ground pool pump and the plastic lid broke. What replacement lid and o ring do I order
 Reply

A  Answered on 6/15/2017 by InyoPools Product Specialist Lennox H.

Hi, Carole. This is the correct lid for the Waterway Mustang 56. You will also need the Trap Lid O-ring - 805-0436.
 Reply


?     Asked on 6/25/2017by Greg B

My ring is stamped 319-3270, will this ring and cover still fit?
 Reply

A  Answered on 6/26/2017 by InyoPools Product Specialist Lennox H.

Greg. Yes, this Lid -319-3260 can be used as a replacement to fit your current pump strainer.
 Reply


?     Asked on 11/12/2017by Samantha

My trap lid is stamped 808-3150.1008. Will this lid fit in its place?
 Reply

A  Answered on 11/14/2017 by InyoPools Product Specialist Lennox H.

Hi, Samantha. This Lid - 319-3260 will work as a replacement. 
 Reply


?     Asked on 5/8/2018by Inyo Visitor

Will this fit pump model number 3410612-1549?
 Reply

A  Answered on 5/8/2018 by InyoPools Product Specialist Hector F.

Yes, this would be the correct lid for the models after 2010 using the plastic ring on the outside brim of the lid. 
 Reply


?     Asked on 10/15/2018by Paul

will this lid fit a first choice pump #56, lid #319-3228
 Reply

A  Answered on 10/16/2018 by InyoPools Product Specialist Lennox H.

Hi, Paul. Yes, this Lid will replace Part # 319-3228. 
 Reply


?     Asked on 6/25/2019by Peter

I have the old style lid of the 319-3260, what o-ring do i need for it?
 Reply

A  Answered on 6/25/2019 by InyoPools Product Specialist Lennox H.

There are at least 2 different o rings that this lid can work with. Please call and provide the model of the pump that your lid goes to, or if you are not sure please send in a few photos of it to upload @inyopools.com so we can confirm for you.
 Reply


?     Asked on 8/12/2019by Lynn Davidson

Will this lid fit this pump

 Reply

A  Answered on 8/14/2019 by InyoPools Product Specialist Michelle B.

Hello, Can you please send a picture of the entire unit?
 Reply


?     Asked on 10/10/2019by Ron

Hello, my pump is a 2-speed HiFlo, HP 2.0 SPL, Model # SD-20-2N11MD. I need the strainer lid, I think it is 319-3260 but hard to read. Also the o-ring. Thank you
 Reply

A  Answered on 10/10/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the lid you will need with the oring. http://www.inyopools.com/Products/07501352020663.htmhttp://www.inyopools.com/Products/07501352023114.htm
 Reply


?     Asked on 5/4/2020by Lauren

I have 311 1400. What lid would fit. I know it's old.
 Reply

A  Answered on 1/20/2021 by InyoPools Product Specialist Hector F.

Hi Lauren, we show this part number as being the volute faceplate to a Waterway SVL56 High Flow pool pump. Please see the parts diagram to confirm that is indeed your pump and the correct lid will be listed on that page. 
 Reply