?     Asked on 1/11/2012by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


?     Asked on 3/6/2015by jim

Does your B663 vertical 3/4 motor replace a 25 year old Arneson pool sweep motor? (Franklin Electric Model 1103025420).
 Reply

A  Answered on 3/9/2015 by InyoPools Product Specialist Robert M.

Hello David - The B663 is the correct replacement motor.
 Reply


?     Asked on 12/11/2016by Robert and Paula

We have a Century Centurion A.O.SMITH Cat B688, with part number 187400-20. It appears very similar to the B663, part number 3250-A58X Will your B663 work for us? Thanks
 Reply

A  Answered on 12/12/2016 by InyoPools Product Specialist Lennox H.

Hi Robert and Paula. It depends on the model of the pump that the motor bolts to. If you can provide us with pump model we can confirm if the B663 motor will replace the B688 motor.
 Reply


?     Asked on 1/24/2017by Inyo Visitor

Will B663 replace my current pump-- part 8-168859-20, cat. no b663
 Reply

A  Answered on 1/25/2017 by InyoPools Product Specialist Lennox H.

Hi, Yes, this is the correct replacement motor for P/N 8-168859-20, CAT No. B663.
 Reply


?     Asked on 4/17/2017by Martin H

Looking for the gasket seal for the base and disc I believe for the model C48J2N127 on the bottom of the Booster pump
 Reply

A  Answered on 4/17/2017 by InyoPools Product Specialist Stacey M.

Hello Martin, what this motor C48J2N127 looks like it matches up with is Arneson Pool Sweep I & II - Booster Pump, I think what you are referring to is number 35.
 Reply


?     Asked on 9/24/2017by Dan

HI, I have the old upright Arneson 3/4 for for my Legend Sweeper. I would buy the newer pump but my plumping is for the old upright Arneson. My question is, does this come with gasket or should part# 3250-A40 Gasket, end Bell? I replace motor once before but no one around sell them anymore. Thanks, Dan
 Reply

A  Answered on 9/26/2017 by InyoPools Product Specialist Lennox H.

Hi, Dan. The End Bell Gasket - A-40 is sold separately, it's not included with the motor. 
 Reply


?     Asked on 8/9/2019by Jp

We have a century b 663, part 7-168859-22 type cx frame G56Y. We used the bell gasket seal when installed and now it’s torn and melted.. could there possibly be a different gasket seal option that doesn’t use the bell?

 Reply

A  Answered on 9/23/2019 by Industry Professional

No other recommended repairs or part, due to safety concerns of water and electric. New motor is suggested. 35-126-3014
 Reply


?     Asked on 4/16/2020by Ashley Arnold

We have one of these attached to our pump set up and it’s noisy. Would that be bearings needing to be replaced, and if so which should I order? Also we don’t even have the sweep for this, can it be disconnected?
 Reply

A  Answered on 12/11/2020 by InyoPools Product Specialist Megan C.

The Bearing, 203 (Single) - 62032RS are the bearings needed, you will need two. A new Pump Shaft Seal 5/8" - PSR-200 will be needed when you remove the impeller to replace the bearings in the motor, the shaft seal will no longer work it will leak if you use the old one. The Booster Pump, Letro 115/230V (LA01N) can be used to replace the whole pump since the other is discontinued. If you are not using a pressure side pool sweep anymore, yes, you can have it removed. Please see PSC Ep. 93: How do I remove my booster pump? http://www.inyopools.com/blog/psc-ep-93-remove-booster-pump/ 
 Reply