The description indicates that the LCD screen is mounted to the back side of the circuit board, but it does not list it as being included in this kit. All I need to replace is the LCD screen. Is that included with this kit (pre-mounted) as part of the circuit board?
Reply
Hi Don, Yes the LCD Screen is included with this kit, the Raypak LCD Screen Can be seen better in this image.
Reply
I see that there is a new three wire temp sensor included. Can the old two wire sensor still be used? Is the three wire temp sensor sold separately?
Reply
No the old 2 wire sensor could not be used and the 3 wire sensor is not sold seperately. The Raypak PCB Board Replacement instructions are really helpful and should help with your installation.
Reply
The LED on my Ray Pak heater has gone bad and I need to replace the PC board. Is this the correct PC board for Model P-R335A-CN, serial number 9908069630 and if so do you have it in stock?
Reply
Robert, The RP2100 Current PC Board (010253F) is the correct replacement for your RayPak model P-R334A-CN Heater.
Reply
my raypak 406a stuck in clk mode. Is this a failed circuit board. Heater 8 years old. Never had a problem b4
Reply
Mark, According to the Raypak Owners/Instructions Manual, "CLK" refers to the "Fireman or Remote switch connected to safety loop is in the OFF mode." You will need to check the switch to make sure it's connected.
Reply
i have a P-R336A the led display has not worked for a while but now the heater will not light, dont have the read out to troubleshoot the problem should I replace the board or could there be a different problem?
Reply
Hi Bobby, You could have two separate issues going on with your heater. The display will need to be replaced and the issue with what is causing the heater not to light. I would recommend having a service technician come out to diagnose the problem.
Reply
I cannot read the temp. display anymore on the heater, otherwise it functions normally. The black numbers are not visible to identify temp setting
Reply
Bill, If the control board functions properly, I would recommend taking a closer look at the control panel that covers it. The plastic may have faded causing it to be difficult to see through.
Reply
The pc board on my RP2100 digital heater has a P/N of 60588. Is this the correct replacement? The connector are positioned different.
Reply
Hi Jim, I was not able to cross reference p/n 60588 to 010253F. This board will work with the RP2100 unit that was manufactured between 11-01-98 thru 10-01-03. We will need to know when the unit was manufactured in order to locate the correct PCB.
Reply
is it possible to replace just the digital display? or, do i need to replace the entire circuit board?
Reply
You would need to replace the entire board as the display is only available with the board and not separately.
Reply
Is this the right one for raypak2100 PR 335A-EN made in 2003......# serial 0303019615 ?
Reply
Hi DG, This board will work with the Raypak 2100 Series Model PR 335A-EN made from 11-01-98 thru 10-01-03 so this board should work for you.
Reply
Replaced board and powered up. Display reads water temperature and indicates "off" mode. Cannot get ithe unit to switch on -- what am I missing? Thanks!
Reply
Hi Shane, You will have to press the "Mode" button to turn the heater "On" in Pool or Spa Mode.
Reply
I HAVE A RAYPAK 2100 POOL HEATER WHICH NOW NEEDS A NEW CONTROL PANEL, PART NO 601687. I CANNOT GET ONE FROM MY POOL SUPPLY. CAN I PURSCHASE ONE FROM YOU ? IF NOT, PLEASE LET ME KNOW WHERE I CAN GET ONE. THANK YOU FOR YOUR PROMPT ATTENTION IN THIS MATTER. BOB HAEMER, MRHAEMER@AOL.COM
Reply
Hi Bob, You can order this board from us. You can place an order through the website (24hrs) or call our office between 9am-8pm EST.
Reply
The LCD died on my Raypak Heater Control board , P/N 601553. Do you have a replacement control board available
?
Reply
Good Afternoon Patrick, Unfortunately I am not pulling anything up with that part number. Can you let us know what the model number of the heater is and the part you want to replace.
Reply
I have an RP2100 digital pool heater. My board is displaying "BRD". After reading up, this indicates to me I need to replace. Is this correct? If so the board p/n is 601533. Is this board available for replacement?
Reply
Hi, Javier. The is the correct replacement PCB you'll for the RP2100 heater in regards the error code BRD. This part is available.
Reply
No digital display. Board panel #601553. Model 185 Propane heater from Leslies Pool. Bought in 2009.
Bought control panel #006739F from INYO POOLS
on 4/28/2017. Still no display, but the controls seem to be working.
Do I need to replace the PC Board?
Reply
Hello William, I would call Raypak 805-278-5300 to run a diagnostic on this model heater and see if they recommend the PCB board be replaced or the heater just needed to be reset.
Reply
Have the RP2100, My gas guys says there is only7/9 volts coming out of the board and won't run the gas.
He says the board needs to be replaced. Does that sound correct or should I check for something else?
Thanks
Reply
Hi Craig, yes that does sound correct. We would suggest replacing your board.
Reply
I'm replacing the control panel and PC board for my RP2100 made in 2003. I understand there is a new PC board for models from 11/98-10/03. My manual says effective 12/03. Will that board and control panel still work on my heater?
Reply
Hi, Leonard. This is the correct replacement if your unit meets the requirements in the Raypak PCB Board Replacement Instructions
Reply
I have an RP 2100.
Serial number 000-2157555
Circuit board number 601588.
Do you have a board that is compatible?
Reply
Hi, Robert. This Raypak RP2100 PCB - 010253F will replace p/n 601588.
Reply
My Raypack Heater will not turn on. I think the circuit board is bad. The model number for the heater is P-R336A-EN-C. Is the correct replacement for the circuit board Part # 6234-162? My display is also bad, what is the part number for it and the cover. Thanks
Reply
PS this was a Raypak heater model P-M336A-EN-C, NO FIRE. Checked pilot no gas has spark. tried using light. no gas. trying to determine gas valve or circuit board. just sent you message asking voltage reading from board to gas valve
Reply
Hi, Randy. To determine if the PCB or gas valve is the issue, Check for 24 VAC across PV-MV/PV terminals on PC board. If voltage is okay, replace gas control; if not, replace PC board.
Reply
I bought this PC board to replace the bad one on my pool/spa heater. Its a raypak 2100- 405A. it worked only one time and after that it gives me a FAN fault. I don't have a nox as part of my unit. How do i turn this off or bypass it. Thanks Kevin
Reply
Hi, Kevin. If you have installed this PCB using the instructions on page 7 of the Raypak PCB Board Replacement Instructions, you're unable to turn that off. I'm not aware of a way to bypass that error code unless you resolve that issue which is tied to a Fan blower.
Reply
I have a 406a gas heater less than a year old. A Milivolt output fault showed up and the gas shuts off. This was after running for 3-4 hours to heat the pool. It was a windy day and I wonder if the pilot was blowing out and causing the unit to shut off. Tried blocking wind with different run time results as I turned the unit off and on all day. Starts up fine and runs for different time periods before the MV shows up.
Reply
You need a service tech, check with Raypak may still be under warranty www.raypak.com or call 805-278-5300
Reply
Unfortunately there is know way for us to be sure without being on site to troubleshoot it. We recommend you have a service tech out or try calling the mfg direct. Raypak has a good website that you can download or read troubleshooting manuals. www.raypak.com
Reply
PS Raypak says that part kit, 010253F,is no longer available.
Reply
Thanks. I clicked on the buy now link and takes me to your answer, but not to the part. I copied the address and pasted it into a new browser window, it takes me to your response. I goggled the part you suggested and got this: Raypak 010253F Replacement for PC Board Controller and Sensor Kit (R185A-R405A) but I have a 406a. Went to Raypak website and nothing comes up for 010253F. Went to Raypak illustrated parts list and all they show is the fuse part number, nothing for the mother board.
Reply
I have a Raypak model# P - R335A-EN, SER#9912081316
Is this the correct board for my unit?
Thank you,
Reply
Hi i installed the 013464F circuit board on my raypak pr335 a year 2000. The three w temp sensor p1 plug adapter is black and the new three wire temp sensor part number 00529913 i installed has a white three wire plug adapter and will not fit on the three wire male black fitting on the board. Did i order the wrong temp sensor. Thanks
Reply
We show the proper part # was 017110F but it has been discontinued by the manufacturer.
Reply
The 013464F was used on units after 2004 & we are not finding a replacement for earlier models. The mfg's tend to not want to support units that are older than 10 years as that is the general life span of a heater. We suggest you contact Raypak direct to see if they still offer a solution the 3 wire temp sensor is all that remains.
Reply
will this work on model #p-r336a-en-c Serial #c612184011
Reply
Hi Phil, the PCB Controller IID Kit, Raypak 206A-408A, 3-Wire, Current - 100-10000345 will be a perfect replacement for the display and controller board in your R336A pool heater.
Reply
