I need a part for my Dolphin pool cleaner but I don't see it on the parts breakdown. Is there still a chance you may still have it?
Reply
The manufacturer which is Maytronics, does not offer all parts for sale. If you don't see a part on the breakdown you can give us a call. For parts that they do not consider "DIY (do it yourself), you will need to contact them and send in the cleaner for repair.
Reply
Does this part connect to the power supply and the cord that comes out of the pool cleaner? I broke the side that connects to the cord.
Reply
This is the piece that goes on the end of the cord that does connect to the power supply. It connects to the power supply and requires a 1.5mm x 50mm hex key or allen wrench for installation.
Reply
Which color wire (white or black) goes into which number (1-4) slot in the plug. Thanks
Reply
Mike, You can call Maytronics at 1-888-365-7446 for instructions on how to install the Amphenol Plug (5000009) to the cord for your Dolphin Cleaner.
Reply
How many pins are supposed to be in that plug that plugs into the power source. Mine only has 2 but I see 4 holes. Can I get a new one or do I need to replace the entire cord?
Reply
Hi Mike, According to Maytronics this is an universal Amphenol Plug which can work with units that has 2-4 pins depending on the features on the cleaner and cord.
Reply
There are 2 wires white and black 4 connections which one does the black wire go to
Reply
Hi Kathy, You will have to contact Maytronics at 888.365.7446 to confirm which wires does where depending on the unit you have.
Reply
can I get the floating power cord with the am phenol plug installed? If so, what is the cost?
Reply
Hi, Some cord comes with the plug, we will need to know the model of the unit you have to confirm if the cord comes with this plug.
Reply
My Maytronics Dolphin's Amphenol plug to the power pack has a black and a white wire connection. The vacuum started and then quit. I checked the plug and found that the set screws for the wires had corroded and that the black and white wires had frayed at their connection points and were shorting-out. I cleaned the plug and disentangled the wires but the unit is dead. Is there a fuse either in the unit or the power pack or is the motor fried forever?
Reply
Hello RJ, I would check Maytronics 1888-365-7446 and run a diagnostic just to make sure that the motor or power supply isn't compromised.
Reply
I have a Dolphin Dynamic serial No 103943BUB5 and I need to replace the plug, Will this one work?
If so, I have a blue,black and white wires. What numbers do I hook these wires up to.
Thanks for your help.
Reply
Good Morning Shreve, This is the pat number you need.Amphenol Plug (5000009). You can call Maytronics at 1-888-365-7446 for instructions on how to install the Amphenol Plug (5000009) to the cord for your Dolphin Cleaner.
Reply
Does this fit a Dolphin Diagnostic Advantage? The female port on the power supply shows two values. Our model uses the two pins rated at 400 VAC at 16 amps, the other two unused pins are rated at 250 V at 12 amps.
Reply
Yes, that will fit your diagnostic advantage cleaner.
Reply
I have the Nautilus Plus (99996403-PC Dolphin Nautilus Plus ) with a 2 pin connection. Can I use the 3 pin amphenol ? One of the pins got bent and I can't connect to my power supply unit now.
Reply
Hello Craig, I would advise calling Maytronics 1-888-DOLPHIN just to check if there is a 2 pin replacement.
Reply
Is there a wiring diagram for installing this on the power cord for the outlet?
Reply
Hi, John. Unfortunately, a wiring diagram is not available. You will have to see how the existing one is wired and go off of that.
Reply
How do you remove the old amphenol plug? It seems like it’s one piece and doesn’t come apart like the new one.
Reply
Hi SArthur, If you go to the 3 minute mark of our How to Repair a Dolphin Pool Cleaner Video then we show this in detail. I hope this helps!
Reply
Sorry I meant, how do you remove the old anphenol plug that is connected to the Dolphin (not the power supply). The 3min mark of your video is for the amphenol plug of the power supply. I need to remove the one that is connec ted to the Dolphin (the plug you use to plug into the power supply).
Reply
Hello, The top and bottom of the plug are threaded. Once you loosen them, you can easily disassemble the amphenol plug.
Reply
Looking for a 2 pin connector for a Dolphin Nautilus pool sweep. Any suggestions where to purchase one? Thanks
Reply
Hi Kathy, this is the link to all the parts we carry for the Dolphin Nautilus, a diagram is included as well for reference.http://www.inyopools.com/parts_maytronics_dolphin_nautilus.aspx
Reply
My power cord separated from the Amphenol Plug ( # 5000009 ) the cord has 2 wires and the plug has four prongs with 4 wire slots. do you have a wiring diagram I can use to reconnect? the plug wire slots are numbered 1 to 4.
Reply
I am sorry, we do not. The How to Troubleshoot a Dolphin Pool Cleaner advises noting where they are to reconnect. If you contact Maytronics directly at (888) 365-7446 they will be able to assist you with the diagram.
Reply
How do you install this plug?
Reply
Hi Linda, Starting at the 3-minute mark of our Dolphin Troubleshooting Video we show How to Replace the Dolphin Amphenol Plug. You should find that video quite helpful.
Reply
My cable is cracked just at the beginning of this part. Can it be cut there and wired into this or does the entire cable have to be replaced
Reply
Hello, You will have to replace the entire cable.
Reply
How do you replace the Amphenol plug, not the socket? There is the socket on the power supply and the Amphenol plug at the end of the cable. The one you are selling the 500009 looks like it comes apart and can be re wired. If not why would you sell it?
Reply
It does come apart, you need to grab the small edge under the threads & hold to untwist & pull apart so you have access to the pins. see images we added.
Will this work on a dolphin c6 plus?
Reply
Hi James, this Amphenol Plug - 5000009 will also work on your Maytronics Dolphin C6 Plus.
Reply