?     Asked on 8/1/2017by Ernest Sealey

Would this board fix the issue of my clock. Clock is not keeping correct time. Or do I need theDisplay Local P-4 & Ps-4 Before Date Codes 0311 - GLX-LOCAL-P-4
 Reply

A  Answered on 8/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Ernest. You will need to replace the PCB of the controller. 
 Reply


?     Asked on 8/4/2017by Inyo Visitor

My ECommand 4 will not keep proper time.When I reset the time and check the clock setting at a later time it has not changed. Thanks PJM
 Reply

A  Answered on 9/15/2017 by InyoPools Product Specialist Andy O.

Hello- You would need to replace the MAIN PCB, E-COMMAND 4 (GLX-PCB-HPC-4).
 Reply


?     Asked on 8/5/2017by Robert McNamara

I have a Hayward "Ecommand 4 Automation System control panel, Model HPC-4-RC w/wireless antenna and 6 function remote. I have to re-set the clock every day or use the remote to activate the filter/vacuum. I only want to replace the circuit board. Hayward insists their part # for the circuit board is GLX-PCB-HPC-4, but that # consistently refers to the entire panel by distributors. Do you carry the CIRCUIT BOARD ONLY for this Ecommand 4 panel? Help!
 Reply

A  Answered on 9/15/2017 by InyoPools Product Specialist Andy O.

Hello Rob- The GLX-PCB-HPC-4 is the part number for the Main PCB, our part number is 2807-110. That is just the PCB, not the entire panel.
 Reply


?     Asked on 10/5/2017by Inyo Visitor

Does this work with aqua connect?
 Reply

A  Answered on 10/5/2017 by InyoPools Product Specialist Megan C.

Yes, the MAIN PCB, E-COMMAND 4 (GLX-PCB-HPC-4) is compatible with the Aqua Connect Home Network - AQCOHOMENET
 Reply


?     Asked on 9/8/2018by Jim

I have hayward model HPC-4-ACT-PC. Will your board 2807-110 be the right replacement for me. (There was no picture for me to compare). Thanks If so. What is your warranty and return policy?
 Reply

A  Answered on 9/17/2018 by InyoPools Product Specialist Lennox H.

Hi, Jim. Yes, this is the correct replacement PCB for your model controller
 Reply


?     Asked on 5/11/2019by Inyo Visitor

After lighting storm main breaker trips when pump starts Board display works the pump runs for a few seconds and trips
 Reply

A  Answered on 5/13/2019 by InyoPools Product Specialist Lennox H.

Hi. This issue could be caused by a bad relay or motor. The Main PCB will not cause this issue.
 Reply


?     Asked on 7/13/2019by Benjamin E. Russ

My e-commander 4 was not keeping time so I replaced the PCB with a new one from this site as suggested. Now it won't switch from pool to spa. Any suggestions?
 Reply

A  Answered on 7/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Benjamin. Check the Local Display connection, if it's okay, then the issue could be the Display
 Reply


?     Asked on 8/30/2019by Inyo Visitor

I have an older e-Command 4 panel. I purchased an AQ-CO-HOMENET Aqua Connect Home Network device. The literature said it was compatible but I believe it seems to only compatible with newer versions, mine is software version 2.85, and the aqua connect device requires version 4.20 or later. Is this replacement board compatible with my panel, and if I swap out my board, will the Aqua Connect work? Also, I do have the AQL2-BASE-RF antenna connected to my panel as well.
 Reply

A  Answered on 9/1/2019 by InyoPools Product Specialist Lennox H.

Hi. In order to get your E-Command Controller up to date to use AquaConnect, you will need to replacement the Main PCB - GLX-PCB-HPC-4 along with the Wireless Antenna - AQL2-BASE-RF.
 Reply


?     Asked on 11/30/2019by Vern Graham

Is the PCB you are selling the updated version that has eliminated the capcitor for the clock.?
 Reply

A  Answered on 12/2/2019 by Industry Professional

Yes it is the latest version & should correct any clock issues.
 Reply


?     Asked on 12/16/2019by GREG

DOES THIS BOARD CONTROL THE TIME CLOCK? tHANKS
 Reply

A  Answered on 12/16/2019 by InyoPools Product Specialist Lennox H.

Hi, Greg. Yes, it does. 
 Reply


?     Asked on 12/30/2019by David

Does this item have a parts warranty?
 Reply

A  Answered on 12/30/2019 by InyoPools Product Specialist Lennox H.

Hi, David. This board is warranted for 1 year. It must be professionally installed. 
 Reply


?     Asked on 2/19/2020by Andrew

I have an E-Command4 and the clock stopped working. This seems to be the correct part number, but the board pictured is slightly different from the one I have. The one I have has 6 connectors (2 yellow, blue,white, violet, gray) connected to a large transformer on the right side of the board. The PCB pictured on this site does not have those connectors. The sticker on the top left side of the board has the number "090007-291-01". The board pictured here has "090007-293-01".

 Reply

A  Answered on 2/20/2020 by InyoPools Product Specialist Lennox H.

Hi, Andrew. The boards are different because you have the incorrect Main PCB for an E-Command System. The board in the picture provided is of an AquaLogic - GLX-PCB-MAIN. If you do have an E-Command System, you'll need to purchased this Main PCB, E-Command 4 - GLX-PCB-HPC-4.
 Reply

  • Commented on 2/20/2020 by Product Owner

    I do have an ECommand 4 system with the board as pictured in my message. This has been working fine for 3 years, so I'm not sure what you mean, it cannot be the wrong board otherwise it wouldn't work. This is all very confusing with the GLX-PCB-HPC-4 and GLX-PCB-MAIN. The GLX-PCB-HPC-4 does not have the 6 color coded connectors to an external transformer, which I'm told is for a salt system.

     Reply

    • Commented on 2/21/2020 by InyoPools Product Specialist Lennox H.

      Andrew, The board will work as it been for the past three years. The board in the picture you provided has ports for the salt cell and flow switch in the lower left of the board which is not used with the E-Command 4 system.  If you do have the salt option, then the GLX-PCB-MAIN is the board you will need. 
       Reply


?     Asked on 5/23/2020by Rob Scott

My board says 007-266-01 3509 PN: G1-066008M-1 Is yours compatable?

 Reply

A  Answered on 5/23/2020 by InyoPools Product Specialist Patrick P.

Hi Rob, Could you let us know if you see any model name on your system like E-Command, Aqua Plus, Pro Logic, Aqua Logic, etc.. this will help us confirm the proper replacement board. Just click the reply link below to supply this info.
 Reply

  • Commented on 5/23/2020 by Product Owner

    Sorry, yes it says Pro Logic Goldline Controls I added a photo. THx

     Reply

    • Commented on 5/25/2020 by InyoPools Product Specialist Patrick P.

      Hi Rob, Thanks for the photos! Since you have the Prologic you will actually require this ProLogic Main PCB Board and not the PCB board on this page.
       Reply


?     Asked on 4/28/2021by Mario Nocito

is this a new board and if not what is the warranty
 Reply

A  Answered on 4/30/2021 by InyoPools Product Specialist Patrick P.

Hi Mario, Yes this is a new board.
 Reply


?     Asked on 5/6/2021by Inyo Visitor

Which replacement board would I need for AQL-P-4-X288?
 Reply

A  Answered on 5/6/2021 by InyoPools Product Specialist Patrick P.

Hi, You will require this AquaLogic Main PCB Board.
 Reply


?     Asked on 5/21/2021by Inyo Visitor

What is the warranty on this part?
 Reply

A  Answered on 5/21/2021 by InyoPools Product Specialist Craig C.

Hello.  This product has a warranty period of 1 year if professionally installed.
 Reply


?     Asked on 5/25/2021by Clyde Schiller

does this board work with Hayward E Command 4 HPC-4. I do not have any remote options on the unit I have.
 Reply

A  Answered on 5/27/2021 by InyoPools Product Specialist Patrick P.

Yes this does work with the Hayward E Command 4 HPC-4
 Reply