?     Asked on 5/20/2016by Inyo Visitor

Iis there a water in and water out side to the 940 inline pool sanitzer?
 Reply

A  Answered on 5/22/2016 by InyoPools Product Specialist Patrick P.

Yes if you are looking at this chlorinator from the front the inlet would be on the left and the outlet would be on the right. Also the 940 Perform-Max Owner's Manual does a good job showing how to install this chlorinator.
 Reply


?     Asked on 5/22/2016by chuck

What size are the inlet ports?
 Reply

A  Answered on 5/22/2016 by InyoPools Product Specialist Patrick P.

The inlet ports are 2" female threaded.
 Reply


?     Asked on 5/29/2016by Deb Teagarden

Is there a replacement lid for sani king performax 910 in line. Serial#407244
 Reply

A  Answered on 6/4/2016 by InyoPools Product Specialist Lennox H.

Hi Deb, The Cap w/ O-ring - 01-22-1418 is the replacement lid for the Sani King Performax 910 In-Line feeder.
 Reply


?     Asked on 9/2/2016by Larry

Is this a generic model?
 Reply

A  Answered on 9/2/2016 by InyoPools Product Specialist Stacey M.

Hello Larry, this is not generic, just a different brand, King Technologies Perform-Max™ Feeders bring you the best in bulk chlorine or bromine feeding. No other bulk feeder offers erosion technology with exact metering capabilities. The Perform-Max™ Feeders are the only feeders with the patented Performance Valve™ that performs on cue, responding accurately to each adjustment in its wide range of settings. so depending on your pools size you can see if they are the right model for you.
 Reply


?     Asked on 6/1/2018by Dave

Can this model be used in-line in an above ground pool?
 Reply

A  Answered on 6/1/2018 by InyoPools Product Specialist Lennox H.

Hi, Dave. If you have a large above ground pool, you can use this model. You will have to follow the installation instructions available in the Perform-Max 940 Owners Manual
 Reply


?     Asked on 6/19/2018by Dianne

Can I purchase the plastic (doughnut-shaped ring with handle) that helps to tighten or loosen the lid on the in-line feeder?
 Reply

A  Answered on 6/20/2018 by InyoPools Product Specialist Joe S.

Yes the Tool, Cap/control Dial (01-22-8870) PART # 9221-18 would be whats needed.
 Reply


?     Asked on 8/19/2018by Fred

Need 1 (One) Upper lid inside gasket for the Perform Max Pool Sanitizer. Have bought from you before. thanks. I will pay with Paypal . Fred.
 Reply

A  Answered on 8/21/2018 by InyoPools Product Specialist Lennox H.

Hi, Fred. The replacement Lid O-ring - 01-22-9926 (Current), 01-22-9426 (Pre-'91) are available based on the age of your unit. 
 Reply


?     Asked on 2/4/2019by Rick

My pool guy overtightened the air bleeder screw on top and broke it off! Can I purchase the air bleeder valves?
 Reply

A  Answered on 2/4/2019 by InyoPools Product Specialist Lennox H.

Hi, Rick. The replacement knob can be purchased, it is listed on the King Perform-Max Feeders Parts Page
 Reply


?     Asked on 4/26/2021by Anthony Natale

Can someone confirm the size dimensions of this product? Your website shows top width of the canister at 7.5 inches and the bottom width of the canister at 7 inches. Then the height (which is far greater than the width) is also listed at 7 inches. I am looking for a replacement feeder and my current canister is 17/17.5 inches tall. Is this a typo on your website (7 inches instead of 17 as it should be)? Let me know. Thanks
 Reply

A  Answered on 4/28/2021 by InyoPools Product Specialist Charlie R.

Anthony, After further review, the height listed is incorrect. It should be 17 inches and NOT 7. You can view the dimensions in the manual HERE
 Reply


?     Asked on 5/21/2021by Michael E. Ferreri

I have a perform-Max 940 In-line brominator that has a slow leak around the dial control. Is there an O-ring in there? Is there a way to rebuild that area without replacing the whole thing?

 Reply

A  Answered on 5/21/2021 by InyoPools Product Specialist Patrick P.

Hi Michael, Yes there is an o-ring behind the dial valve. You will need this Perform Max 940 Dial O-Ring
 Reply