?     Asked on 9/30/2016by Don

Can this flapper check valve be installed in a vertical pipe run?
 Reply

A  Answered on 9/30/2016 by InyoPools Product Specialist Alan M.

Yes this check valve can be installed horizontally or vertically.
 Reply


?     Asked on 12/22/2016by Bruce Sutherland

what is the total length?
 Reply

A  Answered on 12/22/2016 by InyoPools Product Specialist Adam Y.

Good afternoon Bruce, The overall length is 7.5" L by 2-7/8" H.
 Reply


?     Asked on 1/15/2017by Mark

Check value cover has 2 pin holes, Can I purchase cover only? outside diameter is 5"
 Reply

A  Answered on 1/16/2017 by InyoPools Product Specialist Adam Y.

I need to know the pipe size it connects to.
 Reply


?     Asked on 5/26/2017by Inyo Visitor

i want to install this after my de filter and before chlorine feeder...the chlorine is not going to destroy it after a couple seasons?
 Reply

A  Answered on 5/26/2017 by InyoPools Product Specialist Lennox H.

Hi. The check valve is designed especially for high corrosive environments like being installed next to a chlorinator. It will last, I can't say forever but it will for a few seasons. The replacement Corrosion Resistant Flapper Assembly & Cover - 25830-350-800 is available if it fails.
 Reply


?     Asked on 7/18/2017by Skyking

Will this hook up to 1 1/2 inch plumbing without the need for reducers. Will this just slide over my 1 1/2 inch pipe?
 Reply

A  Answered on 7/18/2017 by InyoPools Product Specialist Alex V.

Hello, Yes, 1.5" pvc would fit inside of the check valve. 
 Reply


?     Asked on 4/13/2018by Sam

Hello, Would you recommend this check valve in the suction side of the pool system? Out of the skimmer and before the pump? Sam
 Reply

A  Answered on 4/20/2018 by InyoPools Product Specialist Joe S.

Attached is our How to Guide When To Install a Check Valve in Your Pool Plumbing
 Reply


?     Asked on 4/3/2019by Jared

I've noticed there are check valves vale with a 2 lb. spring and some with 1/2 lb. spring. What is the reason for this? I would like a corrosion resistant valve but only seen it in a 2 lb. I do not want to add any unneeded stress to the system.
 Reply

A  Answered on 4/3/2019 by InyoPools Product Specialist Lennox H.

Hi, Jared. The pump performance or flow rate info is required when sizing a check valve. The higher the flow the higher the spring.
 Reply

  • Commented on 4/4/2019 by Product Owner

    Thank you. I should have known this would be your answer. Unfortunately the data plate to the pump is M.I.A. and all I know it is a Hayward and motor has a sticker with model# UST1072. I am interested in upgrading to a variable speed at some point, but wouldn't know where to begin on sizing it. Could you help?
     Reply

    • Commented on 4/5/2019 by InyoPools Product Specialist Lennox H.

      Jared, If you can provide the following info, I can. The pump housing model, Total Dynamic Head (TDH) and where the check valve will be positioned. 
       Reply


?     Asked on 7/5/2019by Alex Johns

Are the internals of this available to be purchased separately? As in just the clapper and gasket?
 Reply

A  Answered on 7/6/2019 by InyoPools Product Specialist Lennox H.

Hi, Alex. The C.R. Flapper and Cover Assembly - 25830-350-800 is available as a separate part. 
 Reply


?     Asked on 6/6/2022by Douglas A Indovina

My current check valve I feel is causing the spa to drain. There is not much room to install so I have it presently plumbed inbetween 1 1/2 inch pipe. I understand the replacement is 1 1/2 and 2"? How do I install the 2" side?
 Reply

A  Answered on 6/6/2022 by InyoPools Product Specialist Craig C.

Hello Douglas.  The Custom Molded Products Check Valve 25830-350-000 connection ports accommodate 1 1/2" PVC, inside (both sides are 1 1/2" inside connections) and 2" PVC, outside (both sides can accommodate 2" outside connections).  A 2" PVC, Schedule 40 Coupling is used on the outside, and the 2" PVC Schedule 40 Pipe is then connected inside the Coupling.  If the current plumbing is 1 1/2", then the check valve will fit with no changes.  If there is limited space to install a check valve, the Clear Check Valve 1.5" - 1/2 lb. w/ Unions - 1700C15 comes complete with union connections.  The unions can facilitate installation in tight spaces.  The unions are 1 1/2" inside connections.
 Reply