$50.24

Qty:

By Hayward Pool Products


Details

Top

Model # WG1030AVPAK2

Alternate Part #'s WG1030AVPAK2, 55-150-1040, HAY-25-1050, HAYWG1030AVPAK2, HPPWG1030AVPAK2

Product Description

Hayward Main Drains and Covers
Hayward covers safety with variety and style. New safety suction outlets meet all federal requirements.For concrete or vinyl/fiberglass pools, Hayward NSF listed suction outlets are available in a wide range of styles and sizes to satisfy any installation requirement. Whether you install frame and covers, for residential or commercial pools, or sump-type outlets, Hayward suction outlets set the standard in quality and value.

Legislation leads to performance enhancements:
Two major changes in the pool industry address the enhanced performance requirements for pool safety.

  1. The American Society of Mechanical Engineers (ASME) has released ANSI/ASME A112.19.8 – 2007 Suction Fittings for Use in Swimming Pools, Wading Pools, Spas and Hot Tubs. The revisions for this standard include testing of outlet covers to prevent hair entanglement, body entrapment, and finger entrapment as well as improved Ultra Violet (UV) stability of outlet covers.
  2. The Virginia Graeme Baker Pool and Spa Safety act promotes the safe use of pools, spas and hot tubs by imposing mandatory federal requirements for suction entrapment avoidance. Effective December 20, 2008 the Act will be administered by the U.S. Consumer Products Safety Commission (CPSC).*

What do the mandatory federal requirements mean?
Specifically, the mandatory federal requirements are as follows:

  • By December 20, 2008each swimming pool or spa drain cover manufactured, distributed or entered into commerce in the United States shall conform to the ANSI/ASME A112.19.8 2007 Suction Fittings for Use in Swimming Pools, Wading Pools, Spas and Hot Tubs published by ASME. Compliance with this standard will be enforced by the CPSC as a consumer product safety rule.
  • Hayward WG Series Suction Outlet products comply with provisions of the ANSI/ASME A112.19.8 – 2007 standard and the Virginia Graeme Baker Pool and Spa Safety Act.

It is important to determine if a drain cover is compliant with the requirements.
Hayward drain covers compliant with the new standard will have ANSI/ASME embossment on each drain cover to indicate it is compliant.

Product Specifications

Cover Size:
7 7/8 in.
Floor GPM:
125 GPM
Wall GPM:
72 GPM
Color:
White
Cover Shape:
Round
Manufacturer:
Hayward
Size:
7-7/8 in.
Top

?     Asked on 8/27/2012by Guest

I am replacing an existing main drain cover and this one has the correct diameter measurement of 7-7/8". But I need to know the center to center measurements for the screw holes.
 Reply

A  Answered on 8/27/2012 by InyoPools Product Specialist Patrick P.

Thank you for the great question. The center-to-center measurement for this Main Cover screw holes is 6".
 Reply


?     Asked on 9/24/2012by Guest

Does this cover have VGB compliant marked on the top? My inspector is adamant that I need one of these covers and I want to make sure he can see that I am up to code.
 Reply

A  Answered on 9/24/2012 by InyoPools Product Specialist Patrick P.

Yes, this cover does have the VGB label on it top and its service date for when you would need to replace it.
 Reply


?     Asked on 9/25/2012by Guest

my installer says I need a whole new main drain including a sump. Does this product come with the sump?
 Reply

A  Answered on 9/25/2012 by InyoPools Product Specialist Patrick P.

No, this product does not come with the sump. If you need a new main drain with the cover, frame and sump included in this style you should review the following pages WG1051PAK2, WG1052AVPAK2, WG1053AVPAK2, or WG1054AVPAK2.
 Reply


?     Asked on 6/18/2016by gregg skydell

do you carry any main drain covers that the screw holes are 7-1/4 inch from hole to hole ? i have a broken one and can't seem to find the replacement cover.
 Reply

A  Answered on 6/18/2016 by InyoPools Product Specialist Patrick P.

Hi Gregg, You would need this Universal Main Drain Cover which fits all round drains up to 10" wide
 Reply


?     Asked on 5/21/2018by john

I am replacing a suction outlet cover in my pool.The cover came with screws but the holes for the screws to go into on the outlet frame are too big.Do you know if i can buy threaded grommets to put into the holes so the screws will tighten.My pool supplier said the frame should have come with grommets in the plastic frame. I must have covers on top of the suction outlet with a screwed down cover to be compliant with section 1404 of the Virginia Graeme Backer ACT.
 Reply

A  Answered on 5/23/2018 by InyoPools Product Specialist Lennox H.

Hi, John. The frame does have brass grommets to accept the screws. 
 Reply


Top

Review Summary

 (Average 0  out of 5 stars)
0 Rating
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)