Part # PL2674
Dimensions 7" L x 7" W x 1" D
This is a Generic Aftermarket Motor Mounting Plate which can be used on the Hayward® Super Pump™ and is not the Hayward® original O.E.M Motor Mounting Plate.
Used on several Hayward® pumps including the Max-Flo™, Super Pump™, Power Flo II™ and Power Flo III™ as well as Leslie's® Hydramax™ pump.
**Housing Gasket not included... Gasket needed is Housing Gasket**
Housing Gasket can also be found in the Gokit3 and Gokit3Salt
Disclaimer:
All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only.
Can I replace a Hayward SP1600F5 mounting plate with a SP1600F? Will the pump work as designed?
Reply
Hello Buzz - The SP1600F and the SP1600F5 (SPX1600F5) are the same thing. If you order the SP1600F you will receive the SP1600F5 (SPX1600F5).
Reply
The number on my motor mounting plate is spI600f5. Is the spx1600f5 the same?
Reply
Good morning. I believe the plate you have may read sp1600F5 not spi600fs. Please double check the i or 1, for if it is a 1600 then yes it is the same part. Hayward puts the X in part numbers listed in their catalogs but not on the part itself. A little confusing. If it is an i on the plate, I am not sure. If a question still persists, please take a few pictures of your whole pump and send them to me and I will see what I can figure out for you.
Reply
I have a Hayward 1HP super pump that is leaking. I took it apart and replaced the diffuser gasket,#SPX1600R,and the housing gasket,#5110-12. After putting it back together, and making sure all bolts were on tight, it still leaked. Is there something else I should do?
Reply
Hi Tony I would suggest replacing your Hayward Super Pump Shaft Seal as this is a common items which causes leaking.
Reply
Same issue here, and I replaced the pump seal as well. I see a small leak coming from what looks like this piece and the motor connection. Is theirs a part worth replacing before having to buy a new pump?
Reply
Less than 1 hr
Socket Set
I took the motor off of the pump by removing 4 bolts. I disassembled the pump and replaced the part. I saved the old part because the minor damage to it was probably not enough to cause it to fail but I just felt better after the new part was installed.
The Most Recent Reviews
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Worked as expected
Was this review helpful to you?
(5 out of 5 stars) Works great, good fit
Reviewed By: Inyo Customer ()
Perfect fit to my Hayward SuperPump. Very economical upgrade of my unit that failed after motor overheat
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Well built
Was this review helpful to you?
(5 out of 5 stars) Mounting plate fit perfectly.
Reviewed By: Inyo Customer ()
The part fit the pump perfectly.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Just what I needed to rebuild my system
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good quality. Fit perfect
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
easy direct replacement, simple install !
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Great replacement good quality
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
fits perfectly. Quick receipt after order.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect Fit
Was this review helpful to you?
(5 out of 5 stars) WORKS GREAT!
Reviewed By: Inyo Customer ()
WORKS GREAT!
Was this review helpful to you?
(5 out of 5 stars) On time... perfect fit
Reviewed By: Inyo Customer ()
On time... perfect fit
Was this review helpful to you?
(5 out of 5 stars) Perfect fit
Reviewed By: sling00 from TN ()
Pros: Perfect fit
Cons: none
Replaced plate on an older Superpump. Fit perfect.
Was this review helpful to you?