$89.99

Qty:

By Jandy


Details

Top

Part # 4715

Alternate Part #'s 25913-154-000, JDY4715, JND4715

Product Description

Jandy NeverLube 4715 Three Port Valve 1-1/2" - 2" Positive Seal is designed and engineered to be totally maintenance-free. They're easy to install and easy to use. We use the best materials and best design for the ultimate combination of structural integrity and hydraulic flow.

Jandy 3-Way Neverlube Valve

  • Large 1-1/2 - 2 size designed for high flow rates
  • Adjustable stop feature that allows for flow adjustment
  • Placards that label valve position
  • Made from durable CPVC
  • Proprietary NeverLube technology with lifetime guarantee
  • Designed for easy automation

 

Product Specifications

Inside Diameter:
1 1/2 in.
Valve:
3 Way
Outside Diameter:
2 in.
Typical Order Qty.:
2
Top

?     Asked on 4/20/2009by Guest

I just bought a house with a pool. i'v never had a pool so my question is when the pump comes on automaticaly (it has a timer)what position is the jandy valve supposed to be turned to the main drain or skimmer?
 Reply

A  Answered on 4/20/2009 by InyoPools Product Specialist Patrick P.

You can turn the valve so that all the suction is going to the drain at the bottom of the pool, this will suck any dirt or debris on the bottom of the pool through the drain and clean through the filter. If you turn the valve so the suction is going to the skimmer then you will be pulling any leaves or debris off the surface of the pool. You can also set the valve in a half way position so you are pulling from both the skimmer and main drain. I hope this helps.
 Reply


?     Asked on 1/23/2012by Guest

Why do the Jandy valves list ID and OD for each valve?
 Reply

A  Answered on 1/23/2012 by InyoPools Product Specialist Patrick P.

Each Jandy valve is designed to connect to two different size pipes. For example on a valve shown with ID 1 1/2" and OD 2", a 1 1/2" pipe can be glued inside the port or a 2" pipe can be glued on the outside of the port.
 Reply


?     Asked on 4/23/2013by Guest

What are the measurements of this valve?
 Reply

A  Answered on 4/23/2013 by InyoPools Product Specialist Patrick P.

The Jandy 4715 valve is 1.5" id slip/ 2"od slip. The valve is approx 7" wide (top of T) and about 5 1/4" long (top of T to bottom).
 Reply


?     Asked on 9/23/2014by Guest

I have this valve installed at my pump. I have a lot of air coming out of the pool jets and it doesn't stop. If I rotate the valve to vacuum and back to skimmer, it clears the air immediately. Do you have any suggestions?
 Reply

A  Answered on 9/23/2014 by InyoPools Product Specialist Patrick P.

I would recommend checking the gaskets/o-rings on the valve and pump housing. They may be letting air into the system.
 Reply


?     Asked on 1/12/2015by Bob

Can this valve be turned off so no water flows out?
 Reply

A  Answered on 1/12/2015 by InyoPools Product Specialist Megan C.

Hello Bob,Yes, you can completely close one of the three ports. The handle on the valve has "Off" molded into the plastic, the location it is facing confirms that the port is closed off. 
 Reply

  • Commented on 5/3/2020 by Product Owner

    Just to be clear...We close off either one of the other two ports, correct?
     Reply


Top

Review Summary

 (Average 4.95  out of 5 stars)
20 Rating
5 star:
 
(19)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews