$460.63

Qty:

By Spa Parts Plus


Details

Top

Part # 9710-28

Manufacturer Code 52213

Dimensions 8.5" L x 6" W x 1" D

Alternate Part #'s 33-52213-K, 52213, R576R1B, R576R1C, 59-355-1599, BB52213

Product Description

BALBOA BOARD R574/6 FOR JACUZZI VALUE PAK

CHIP # R576R1C

DIMENSIONS: 6" X 8 1/4"

THIS IS A CIRCUIT BOARD MADE BY BALBOA THAT IS USED ON THE JACUZZI WHIRLPOOL BATH VALUE SYSTEM THIS SYSTEM IS USED ON A LOT OF THE SPAS SOLD BY HOME DEPOT THAT ARE MADE BY JACUZZI WHIRLPOOL BATH

THERE ARE TWO VERSIONS OF THIS: R574 AND R576 R576 HAS (2) SINGLE SPEED PUMP R574 HAS (1) TWO SPEED PUMP THIS BOARD WILL WORK FOR BOTH SYSTEMS, THERE IS A JUMPER ON THE BOARD THAT CONTROLS THIS

2 FOUR PIN FEMALE PHONE PLUGS

120 VOLT - 12 VOLT TRANSFORMER

TEMP SENSOR USED WITH THIS IS INYO # 9711-100 (BALBOA # 30352)

HI LIMIT SENSOR USED IS INYO # 9711-101 (BALBOA # 32016)

ORIGINAL TEMP SENSOR WAS BALBOA #30344 THE 32016 REPLACES THIS ONE DIFFERENCE IS ONLY THAT ORIGINAL 30344 HAD A 12" CORD THE REPLACEMENT 32016 HAS A 24" CORD SPASIDE CONTROL TO USE WITH THIS IS 9705-36

Top

?     Asked on 4/3/2019by Drago D Nikolich

Was looking for balboa circuit board 46308 SN 004C395B , We got great pump from you but did not spot burnt corner of circuit board. Thank you so much for your time and help

 Reply

A  Answered on 4/4/2019 by InyoPools Product Specialist Lennox H.

Hi, Drago. This board resembles your board. However, we will need the Chip Number which is located on the white sticker to confirm.
 Reply

  • Commented on 4/14/2019 by Product Owner

    Will this c board fit ok
     Reply

    • Commented on 4/22/2019 by InyoPools Product Specialist Lennox H.

      Drago, Yes, this board will fit without any other modifications. 
       Reply

      • Commented on 5/3/2019 by Product Owner

        I need wet end for pump that I purchased from you , pump working well but have leak on rubbery end part, thank you for your help
         Reply

        • Commented on 5/4/2019 by InyoPools Product Specialist Lennox H.

          Drago, You will need to provide us with the model of the wet end you have so that we can match a replacement. We have more than 30 different wet ends that can mount to your pump. 
           Reply

          • Commented on 5/5/2019 by Product Owner

            I'm hoping that image is clear , thank you
             Reply

            • Commented on 5/6/2019 by InyoPools Product Specialist Lennox H.

              Drago, The replacement Wet End is p/n 5069-615
               Reply

  • Commented on 4/14/2019 by Product Owner

    Will this c board fit ok
     Reply


?     Asked on 4/4/2019by Drago D Nikolich

I hope numbers are clear to read , thank you for quick response

 Reply

A  Answered on 4/5/2019 by Industry Professional

This is the correct part. However, the original board is NLA through Balboa Water Group, there is an alternate option which will be shipped made by Hydro Quip.
 Reply

  • Commented on 4/6/2019 by Product Owner

    Should I undo my order and how to pick right one , would like to buy right fitting connecting parts. Thank you for your patience
     Reply

    • Commented on 4/11/2019 by InyoPools Product Specialist Lennox H.

      Drago, No need to, you will be shipped the current circuit board.
       Reply


?     Asked on 4/15/2019by Drago D Nikolich

I send pictures but will try again thank you, if board need different electrical connector would like to get them also

 Reply

A  Answered on 4/15/2019 by InyoPools Product Specialist Lennox H.

Hi, Drago. I'm confirming that this Circuit Board - 52213 is the correct replacement.
 Reply


Top

Review Summary

 (Average 0  out of 5 stars)
0 Rating
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)