Part # 5002-14
Manufacturer Code 355329
Dimensions 10.5" X 0.2"
Black rubber front housing o-ring for Pentair / Pac Fab Challenger and Waterfall pumps.
Square Ring, Pentair PacFab/Sta-Rite, Volute, O-506
I've just replaced my housing gasket because I had quite a water leak. The new gasket also leaks. Is there one way the gasket should go on? Or is there something else that could be causing the leak? Water is coming out at a pretty good clip.
Reply
Have you checked the shaft seal yet? The shaft seal is located behind the impeller and if it leaks it will come from the union where the motor bolts to the pump. Shaft seals depend on the pump model.
Reply
I have an older Challenger pump with 35-5188 diffuser. I need to find out how to tell whether I need a round o-ring or square o-ring for both the diffuser and the housing. I ordered the GO-KIT5 that contains both round o-rings. The pump has been serviced multiple times by various people and not sure if round is correct versus square….I have found both types in the used parts box. Thanks
Reply
Hi John, The Diffuser (35-5188) is used on the Pentair Challenger High Pressure Pumps. The round o-rings not the gaskets are used with the high pressure pumps.
Reply
procedure for replacing housing gasket 355329
Reply
Unscrew the clamp holding both halves of the pump together. Remove the old gasket. Lubricate and install the new gasket. Reattach both halves of the pump and tighten with the clamp.
Reply
Does the Gasket housing 35-5329 have a round or square profile.
I recently installed a new motor on my Challenger pump and used the Gokit5, but the round gasket in the kit didn't work and I need the square gasket.
Thanks
Reply
Hi, John. This Housing Gasket - 355329 is squared.
Reply
The gasket is not square, so my question is does the longer edge get installed against the front housing or the short? It does not seem to fit 100% tightly with the thinner edge, but also does not seem to fit perfectly the other way either.
The one that came off the pump was the square cut one as well, but I am wondering if even that one was the correct one...
Reply
Hi, Chris. The short side of this gasket is placed against the volute. It will seal once the two halves compresses the longer side of the gasket.
Reply
1 to 2 hrs
Nut Drivers, Socket Set, Wrench Set
Squealing bearings in pump motor. I pulled pump motor (challenger IIHS, 1HP) and rebuilt with new bearings. I learned how to do this as a kid working at a bowling alley. When replacing, I always replace the two O-rings on the pump (both are the square variety) and the sleeve bearing for the motor. Makes quick work and no leaks!
Quiet as a mouse again.
Less than 1 hr
None
Turn pump off
Drain water from pump
Remove big clamp around housing
Seperate pump from strainer housing.
Remove o ring from front of pump and replacewith new one.
Marry pump back to strainer
Put clamp back in position lining up with arrow
Tighten clamp
Fill strainer with water to help prime pump
Turn pump on and check for leaks
The Most Recent Reviews
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
as advertised
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good quality and correct size. Would purchase again.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Part worked very well.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
An absolute must to replace this every spring, or when doing a rebuild. Also need to know which pump model you have, because there is also a round gasket, which will not work in my Challenger II pump.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Quality product and fast delivery
Was this review helpful to you?
(5 out of 5 stars) Well made square o-ring to replace old stretched one
Reviewed By: Inyo Customer ()
It works great. Installed it with a new motor 14 months ago and it's been working great !
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good quality
Was this review helpful to you?
(5 out of 5 stars) Works like it should
Reviewed By: Inyo Customer ()
Works perfectly.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
worked great
Was this review helpful to you?
(5 out of 5 stars) Critical part
Reviewed By: davis11 from Lafayette, LA ()
I wasn't sure about the size or type I needed but customer support advised me and it was a perfect fit.
Was this review helpful to you?
(5 out of 5 stars) Helps make the pool pump strong
Reviewed By: Michael N. from Copperas Cove, TX ()
Pros: Fits well, does what it supposed to.
Cons: None
My pump had a problem pumping strongly, so I ordered this and some other items and replacing everything at once cleared up all problems.
Was this review helpful to you?
(5 out of 5 stars) gasket
Reviewed By: Karen M. ()
quick delivery.
Was this review helpful to you?
(5 out of 5 stars) gasket
Reviewed By: Karen M. ()
quick delivery.
Was this review helpful to you?
(5 out of 5 stars) Excellent Gasket
Reviewed By: K K. from Poway, CA ()
Used this to replace a worn gasket on a pre-1990 PacFab housing. Local suppliers had only the square gasket which does not work on the older equipment. Was inadvertantly sent the square one, but with excellent customer service, it was replaced promptly with the round gasket. No more leaks!
Was this review helpful to you?
(5 out of 5 stars) Perfect fit!
Reviewed By: J Scott S. from Wilmington, NC ()
Perfect fit and delivery was quick. Grea advice too
Was this review helpful to you?
(5 out of 5 stars) housing gasket
Reviewed By: Kenneth H. from Myrtle Beach, SC ()
Very fast delivery, easy ordering and excellent product. Will order all my pool needs through you...
Was this review helpful to you?
(5 out of 5 stars) perfect fit gasket
Reviewed By: Kenneth H. from Myrtle Beach, SC ()
Very fast delivery, easy ordering process and excellent product.. Thank You!!
Was this review helpful to you?
(5 out of 5 stars) Gasket from InYoPools
Reviewed By: Kimberly M. from Atlanta, GA ()
Thanks InYoPools...as usual great OEM products carried with exceptional service and support. I recommend your website to all my friends that have pools.
Was this review helpful to you?
3 2
(4 out of 5 stars) What would happen if company sends wrong part by mistake?
Reviewed By: S.T.P. from STP in Lodi, CA ()
Pros: Right parts and right customer service.
Cons: Warehouse mistake, but immediate fix--no hassle.
I have an older Pac Fab pump and impeller set up--pre 1990. Local CA pool supply says can't get parts--so sorry. Inyo has parts and says no problem. Gasket shown is square while my older equip needs round gasket. Look close at pic. Inyo has both in stock. Square arrived instead of round. Called Inyo--no prob--correct part arrived 5 days later, no charge, no questions asked. Both parts and customer service--top drawer.
Was this review helpful to you?
(4 out of 5 stars) Replacement Gasket Great.
Reviewed By: Meltim from Ft. Worth, TX ()
Though the replacement gasket is round, rather than square, as shown, it nonetheless is fully functional. Very fast receipt, too.
Was this review helpful to you?
(5 out of 5 stars) Parts came as ordered
Reviewed By: Shorty ()
Parts came as ordered.
Was this review helpful to you?
(5 out of 5 stars) Good fit worked well
Reviewed By: handyman from Scottsdale, AZ ()
Pros: No problems, delivered as planned
Was this review helpful to you?