Part # 3525-071
Manufacturer Code 79101600
Dimensions 8-1/4" X 7/8"
lens gasket used on Amerlite incandescent and IntelliBrite LED pool lights. White rubber o-ring goes between the face ring and glass lens to prevent water from entering the light fixture.
Is this the correct gasket for American Products Model R-100 BC? Also, is there an LED bulb I can use? The product indicates R-30; 100 watt; 12 volt. Thanks very much.
Reply
Good morning Henry, Yes, This is the correct lens gasket. I would recommend the LED Pool Bulb Color Changing 12V 18W - PL5815. It is a great bulb and it is on sale at only $99.00.
Reply
I have two American Products pool lights. 500 watts / 120 V/ R40 bulb type. I have replaced gaskets already and a pool repair guy reinstalled lights. Both of them leaked. I have put silicone on the power cord leading into the light housing. The light housing says series 7885xx, 7845xx, 7895xx. Use with model 7821xx, 7822xx, 7823xx, 79206700, 79208900 fixture housing. Wet niche type.
What is the right gasket? Thanks.
Reply
Hi Jon, this is the correct lens gasket for the pool light you have listed.
Reply
I have same question as Jon F from 6/13/2017. My light has a label with exactly the same model numbers. However, the old gasket measures 8 ¾ OD, 7 ½ ID and 5/8 thickness. Your website shows the dimensions as 8 ¼ OD, same ID of 7 ½ and thickness of 7/8. Has my old one been compressed so much that its thickness has reduced and the OD increased? Also, should I use any lubricant with the new gasket?
Reply
Hi, Peter S. If you're measuring the gasket while it is on the lens then it will be a little bit larger in diameter because the gasket stretches over the lens. No lubricant is required when installing this gasket.
Reply
Hello. I have a Pentair Amerlite p/n 78456300. My current white gasket around th lens measures 8.5” OD, 7.5” ID and what appears to be 3/4” thick. To my knowledge this is the original gasket that came with the light 3 years ago. Is this gasket a correct (exact) replacement?
Reply
Less than 1 hr
Screwdriver, Nut Drivers
After watching an Inyo Pools DIY video on how to replace your pool light, it was recommended that you replace the lens gasket as well. It was a simple remove and replace. If you dont see water in the lens and the light is working there is no need to replace the gasket. Replacing it while I had the fixture open made sense and added extra confidence that there wouldn't be any leaks.
The Most Recent Reviews
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Very satisfied
Was this review helpful to you?
(5 out of 5 stars) Just Right
Reviewed By: Inyo Customer ()
Just right
Was this review helpful to you?
(5 out of 5 stars) Seal must be put in right
Reviewed By: R S. from Anaheim CA ()
Pros: Fits
Cons: Must be installed correctly
Installed new bulb and seal in old Anthony pool. First install leaked like a sieve. My brother, who actually is a rocket scientist, happened to be visiting and noticed a very slight bevel on one side of the ring (which should face the light). Reversed it and so far no leaks.
Was this review helpful to you?
(2 out of 5 stars) gasket
Reviewed By: Pool Fan ()
This gasket was very hard to install. It worked for a while, but after the winter it leaked and had to be replaced.
Was this review helpful to you?
(5 out of 5 stars) Perfect Light Gasket
Reviewed By: Caryl K. from Apache Junction, AZ ()
Pros: Perfect fit
Cons: None
This gasket is the perfect fit for the light in my 19 year old pool. Easy to install and sealed up tight. Would certainly purchase again.
Was this review helpful to you?
(5 out of 5 stars) Tight fitting gasket that did the job.
Reviewed By: Dick from Escondido, CA ()
This lens gasket arrivfed quickly and in excellent shape. It was the proper fit and sealed my underwater light fixture.
Was this review helpful to you?
(5 out of 5 stars) Gasket for underwater lens
Reviewed By: Dick from Escondido, CA ()
Pros: The gasket, bulb and lens were the exact size needed.
This gasket fit precisely onto the lamp holder and has proven to be an effective seal.
Was this review helpful to you?
(5 out of 5 stars) OEM Equivalent Gasket-Perfect Fit!
Reviewed By: Spa Repair Guy from Ventura, CA ()
Gasket was perfect replacement for OEM gasket. Perfect fit and no problems.
Was this review helpful to you?
(5 out of 5 stars) light gasket
Reviewed By: Rogelio R. from antioch , CA ()
I bought this product for my pool light and it was well worth the money. I previuosly bought a gasket at leslie's pool supplies for the same light and it didnt work at all it was a waste of money water just got rigth back in to the light.
Was this review helpful to you?
(5 out of 5 stars) works great
Reviewed By: Rick P from Rogers, AR ()
Pros: does what it is supposed to use. Easy to install
Cons: none
Works as promised. keeps water out - great replacement. use when changing lightbulb
Was this review helpful to you?
(5 out of 5 stars) perfect gasket
Reviewed By: RICHARD P. from PEORIA, AZ ()
fit perfect
Was this review helpful to you?
(5 out of 5 stars) Perfect Fit
Reviewed By: SwimOH from Granville, OH ()
Pros: Great fit, OEM, easy to install
Was this review helpful to you?