$486.51

Qty:

By Hayward Pool Products


Details

Top

Part # 2807-41

Manufacturer Code GLX-PL-LOC-P-4

Dimensions 6-1/8" X 4-1/2"

Alternate Part #'s GLX-PL-LOC-P-4, GLXPLLOCP4, HPPGLXPLLOCP4

Product Description

Introducing the Ultimate Replacement Control Panel for Your Hayward ProLogic and E-Command Pool Automation System!

Upgrade and rejuvenate your pool experience with our state-of-the-art Replacement Control Panel, designed exclusively for Hayward ProLogic and E-Command pool automation systems. Whether you're a pool enthusiast or a professional pool manager, our control panel is your key to effortless pool management and control.

 

Local Display ProLogic P4 Only - GLX-PL-LOC-P-4

 

Your Source for Swimming Pool & Spa Parts With 40,000 Parts in Stock - INYOpools.com

Top

?     Asked on 9/1/2015by Shannon Fancher

The tape that was on the diplay came off. I can read only parts of my display. Is there a replacement film of some sort to buy for this.
 Reply

A  Answered on 9/2/2015 by InyoPools Product Specialist Joe S.

unfortunately not, you must purchase the complete display unit
 Reply


?     Asked on 8/5/2016by joe

do you have the pro logic display in stock
 Reply

A  Answered on 8/5/2016 by InyoPools Product Specialist Scott W.

It's going to depend on which display you're needing. Is it a ps4, ps8 or ps16?
 Reply


?     Asked on 9/19/2016by gary

I have a Hayward Aqua Plus (PL-Plus), and the down button on the local display isn't functioning. The image of Pro Logic P4 looks identical, but is it compatible? thank you
 Reply

A  Answered on 9/29/2016 by InyoPools Product Specialist Lennox H.

Hi Gary. This local display is compatible with the Hayward Aqua Plus controller.
 Reply


?     Asked on 4/26/2017by Inyo Visitor

Is my display controls repairable. It works but can't read the screen
 Reply

A  Answered on 4/27/2017 by InyoPools Product Specialist Scott W.

What is the model of your automation system so I can identify replacement places for your system.
 Reply


?     Asked on 5/15/2017by Cody Simmons

I installed new cell, I went to a T-5 from a T-15 because from new installation it was over kill due to my pool being only a 15000 gallon pool. Now that I have installed new cell and changed to T-5 in the diagnostic menu. But now I get error High Salt when I know the salt level is low. Can you help. Thanks
 Reply

A  Answered on 5/21/2017 by InyoPools Product Specialist Alex V.

Cody, Did you set the system to read a T-5 cell? If not, that may be your issue.
 Reply


Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver

2     0

My display was not working properly and was constantly blinking. sometimes it was impossible to change any configuration on it.

Written on 11/4/2023 by Guest

I found the compatible display easily on your website. the following steps i took to replace the display.
1. Open the box. Turn off all switches to the filter.
2. remove 3 screws from the box. remove the Pro Logic P-4 Local Display from the standoffs mounted on the main PCB.
3. remove the Pro Logic P-4 Local display cable connected to the main PCB.
4. Since that cable was not shipped with my new display, i removed it from my old display and connected it to my new display using the below steps.
a. remove the cover from the old display. disconnect the cable.
b. remove cover from new display and reconnect the cable to the new display. put both covers back on.
5. Now take the new display with the cable and connect it to the main PCB.
6. Mount the display to the 4 standoffs on the main PCB.
7. close the cover, put the screws back on. power on the switches and verify the display works.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver

1     0

Our original Local display ProLogic P4 was twelve years old and the right arrow button had stopped working

Written on 6/18/2020 by Guest

I ordered a replacement from INYOPOOLS.com which arrived this morning. To connect the new display I turned off the pool filter and shut off the power to the box. I unscrewed the facia panel and simply pulled off the display from the motherboard which is sitting on four plastic pins.

I removed the back of the old display, removed the one four pin connecter and inserted the connector to the new display. The four wire connector needs to be put through the back of the new display connected then the display case is then easily pushed together and mounted on the four plastic pins.

I then screwed the facia panel back, turned the power on. The new display came on so much brighter than my old and I checked all the buttons to make sure everything worked. So pleased I replaced the display I was over scrolling through all the settings backwards!!

Very happy. This was an easy fix, should have replaced a year ago!

Were these instructions helpful? 
 

Top

Review Summary

 (Average 5  out of 5 stars)
2 Rating
5 star:
 
(2)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews