Product Description

INYO # 3800-111 TRIODYNE # TSS-2800CK THIS IS COMPLIANT WITH THE ASME/ANSI A112.19.8-2007 REGULATIONS AS SPECIFIED BY THE VIRGINIA GRAEME BAKER POOL AND SPA SAFETY ACT THIS IS A VGB-2008 COMPLIANT COVER

************************************************

GENERAL DESCRIPTION: 8" ROUND RETROFIT MAIN DRAIN COVER WITH ADAPTOR, WHITE

************************************************

BASIC SPECS: THIS IS A TSS-2800 COVER WITH AN ADP-2000 ADAPTOR THIS IS DESIGNED TO RETROFIT THE STA-RITE MAIN DRAINS FOR EXACT SPECS ON THE ADP-2000 ADAPTOR, SEE PART NUMBER 3800-050 CENTER TO CENTER SCREW HOLE MEASUREMENT: (4 DIFFERENT SIZES ARE POSSIBLE - SEE "SCREW HOLES" BELOW FOR MORE DETAILS ON THIS) 2 SCREW HOLES 7" APART (PRE-DRILLED) 2 SCREW HOLES 6-5/8" APART 2 SCREW HOLES 6-5/32" APART 2 SCREW HOLES 6" APART USAGE: APPROVED FOR FLOOR USE ONLY USE ON A NON-HORIZONTAL SURFACE IS NOT APPROVED SPECS: SPECS SHOWN ARE FOR A SINGLE UNIT FLOOR: 68.8 GPM @ 2.28 FPS LIFE: 7 YEARS TOTAL OPENING: 9.678 SQ INCH 45.245 GPM @ 1.5 FPS

************************************************

DETAILED DESCRIPTION: THIS IS KNOWN AS THE "ANTISNARE PLUS" COVER THIS IS AN ANTI-ENTRAPMENT RETROFIT COVER AND SCREWS THIS COVER DOES NOT HAVE A SINGLE SOLID CENTER TOP PIECE. THE COVER HAS A CIRCULAR OUTSIDE RING WITH 5 LARGE AND 5 SMALLER FINGERS WITH OPENINGS BETWEEN EACH. THESE NARROW AND SLOPE UPWARD TOWARD THE CENTER OF THE DRAIN. AT THE BOTTOM THESE EXTEND BELOW THE LARGE RING TOP RING. UNDER THE BOTTOM THESE START IN A SMALLER CIRCULAR RING WHICH EXTENDS BELOW THE TOP RING. MATERIAL: PLASTIC COVER AND ADAPTOR, STAINLESS STEEL SCREWS COLOR: WHITE SHAPE: ROUND

************************************************

COVER DIMENSIONS: COVER OUTSIDE DIAMETER: 7-5/8" (A) (MAIN FLANGE RING) COVER BOTTOM RING DIAMETER: 5-5/16" THIS EXTENDS 1-1/4" BELOW THE BOTTOM OF THE MAIN FLANGE RING COVER TOTAL HEIGHT: 2-11/16" (B) MAXIMUM HEIGHT ABOVE MAIN DRAIN BODY: 1-7/16"

************************************************

SCREW HOLES USED: WHEN USED WITH THE ADP ADAPTOR, THE PRE-DRILLED HOLES 7" APART ARE USED TO ATTACH THE COVER TO THE ADAPTOR THE ADAPTOR HAS SCREW HOLES USED TO ATTACH IT TO THE STA-RITE SUMP SCREW HOLES: (THIS IS A LIST OF ALL THE SCREW HOLES IN THE COVER) THERE ARE 4 DIFFERENT SETS OF POSSIBLE SCREW HOLES THE SCREW HOLES 7" APART ARE PRE-DRILLED AND COUNTER SUNK THE REMAINING 3 SETS HAVE COUNTER SINKS BUT ARE NOT PRE-DRILLED. MEASURED FROM CENTER TO CENTER OF SCREW HOLE THESE ARE THE 4 SETS 2 SCREW HOLES 7" APART (PRE-DRILLED) 2 SCREW HOLES 6-5/8" APART 2 SCREW HOLES 6-5/32" APART 2 SCREW HOLES 6" APART

************************************************

SCREWS: THERE ARE 2 DIFFERENT SETS OF SCREWS INCLUDED WITH THIS COVER THE LARGER SCREWS ATTACH THE COVER TO THE ADAPTOR THE SMALLER SCREWS ATTACH THE ADAPTOR TO THE SUMP 2 SCREWS - #14 X 5/8" SELF TAPPING 4 SCREWS - #6 X 5/8" SELF TAPPING

************************************************

MARKINGS: TSS-2800C WHITE IS MOLDED INTO ONE OF THE LONG FINGERS ON TOP OF THE COVER MODEL ADP-2000 IS MOLDED INTO THE COVER (THE ADAPTOR SHOWS THAT IT MAY BE USED WITH THE TSS-2000 SERIES BUT PER THE MFG IT MAY ALSO BE USED WITH THE CURRENT TSS-2800 SERIES COVERS) THE SPECS REQUIRED BY THE VGB-2008 LAW ARE ALSO MOLDED ON THE COVER