Product Description

INYO # 3818-002 DRAINSAFE # DS 360M THIS IS COMPLIANT WITH THE ASME/ANSI A112.19.8-2007 REGULATIONS AS SPECIFIED BY THE VIRGINIA GRAEME BAKER POOL AND SPA SAFETY ACT THIS IS A VGB-2008 COMPLIANT COVER

************************************************

GENERAL DESCRIPTION: 8" ROUND RETROFIT MAIN DRAIN COVER, WHITE (THIS REPLACEMENT COVER IS ABOUT 10" DIAMETER ITSELF BUT IS DESIGNED TO REPLACE COVERS IN THE 8" ROUND GENERAL RANGE)

************************************************

BASIC SPECS: CENTER TO CENTER SCREW HOLE MEASUREMENT: 5-1/2" TO 7-1/2" (REPLACES COVERS WITH HOLES IN THIS THIS SIZE RANGE) USAGE: APPROVED FOR FLOOR OR WALL USAGE SPECS SHOWN BELOW ARE FOR A SINGLE UNIT FLOOR: 123 GPM WALL: 123 GPM LIFE: 3 YEARS TOTAL OPENING: 27.0 SQ INCH

************************************************

DETAILED DESCRIPTION: THIS IS THE DRAINSAFE 360M COVER THIS IS AN ANTI-ENTRAPMENT RETROFIT COVER AND SCREWS THIS COVER DOES NOT HAVE A SINGLE SOLID CENTER TOP PIECE. THE COVER IS DOME SHAPED WITH A VERY FINE GRATING ON TOP. THERE ARE 2 SOLID CROSS PIECES 21/32" WIDE WHICH EXTEND FROM SIDE TO SIDE AND CROSS IN THE MIDDLE. THESE CROSS PIECES ARE THE TOPS OF THE 2 BRACES WHICH EXTEND FROM TOP TO THE BOTTOM OF THE COVER. THERE IS AN OVAL CUT-OUT ON EACH SIDE OF EACH BRACE, WHICH IS WHERE THE COVER SCREWS WILL BE PLACED. EACH CROSS PIECE EXTENDS SLIGHTLY BEYONE THE OUTSIDE DIAMETER OF THE COVER AND EXTEND ABOUT 1/4" BELOW THE BOTTOM OF THE OUTSIDE RING. THERE ARE 2 SMALL FEET BETWEEN EACH CROSS PIECE AT THE OUTER EDGE. THIS GIVES A TOTAL OF 12 SUPPORTS AROUND THE OUTSIDE EDGE. MATERIAL: PLASTIC COVER, STAINLESS STEEL SCREWS COLOR: WHITE SHAPE: ROUND

************************************************

COVER DIMENSIONS: COVER OUTSIDE DIAMETER: 10" (A) (MAIN FLANGE RING) (EACH CROSS PIECE AND FOOT EXTENDS 1/8" PAST THE MAIN DIAMETER MAKING THIS 10-1/4" ACROSS AT THE MAIN CROSSPIECES) COVER TOTAL HEIGHT: 1-5/16" (B) MAXIMUM HEIGHT ABOVE MAIN DRAIN BODY: 1-5/16" THE OUTSIDE RING SITS 1/4" ABOVE THE BOTTOM OF THE COVER

************************************************

SCREW HOLES: THIS COVER IS DESIGNED TO ALLOW PLACEMENT OF SCREWS ANYWHERE FROM 5-1/2" TO 7-1/2" APART MEASURED AT THE CENTERLINE OF THE SCREW EACH CROSS BRACE HAS AN OVAL OPENING ON EACH SIDE. EACH OPENING IS ABOUT 3/4" LONG AT THE BOTTOM. AT THE TOP THESE ARE MOLDED TO CONFORM TO THE COUNTERSINK TYPE HEAD OF THE SCREWS. ON ONE BRACE THESE ARE 6-1/4" APART AT THE INSIDE AND ON THE OTHER THEY ARE 5-1/4" APART. SINCE THE OVAL HOLES ARE TAPERED THIS SETS THE SCREW BACK JUST A LITTLE FROM THE EDGE OF EACH OF THE OVAL HOLES. THE INSTRUCTIONS CALL FOR DRILLING 2 ADDITIONAL HOLES INTO THE MAIN DRAIN MUD RING AT A 90 DEGREE OFFSET FROM THE FIRST 2 SCREW USING THE ADDITIONAL 2 OVAL OPENINGS IN THE OTHER CROSS PIECE TO ATTACH THE NEXT 2 SCREWS. THE COVER WILL THEN BE ATTACHED BY A TOTAL OF 4 SCREWS

************************************************

SCREWS: THE SCREWS SUPPLIED WITH THE COVER HAVE A VERY SPECIAL TYPE HEAD WHICH RESEMBLES AN ALLEN HEAD SCREW. THE CORRECT TOOL TO INSTALL THESE IS INCLUDED WITH THE COVER 2 SCREWS - #8 X 1-1/2" SELF TAPPING 2 SCREWS - #8 X 2" SELF TAPPING 2 SCREWS - #8 X 1" SELF TAPPING 2 SCREWS - #10 X 1-1/4" SELF TAPPING 2 SCREWS - #8-32 X 1-1/4 MACHINE THREADS 2 SCREWS - #10-24 X 1-1/4" MACHINE THREADS

************************************************

MARKINGS: DS 360 M IS MOLDED INTO ONE OF THE CROSS PIECES ON TOP THE SPECS REQUIRED BY THE VGB-2008 LAW ARE ALSO MOLDED ON THE COVER