?     Asked on 1/11/2012by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


?     Asked on 1/12/2012by Guest

Why do I need to purchase a new shaft seal?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
 Reply


?     Asked on 1/12/2012by Guest

Why should I purchase a Tune Up Kit?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
 Reply


?     Asked on 1/18/2012by Guest

I'm trying to find a replacement motor for my pool pump but my model number doesn't match what you have listed as the model number. My model number begins with a C48 and yours begins with an SP. Please help.
 Reply

A  Answered on 1/18/2012 by InyoPools Product Specialist Patrick P.

What we have listed on our chart pages is the pump model number. The model number you have will just identify the motor. If you look on the plastic housing on the pump there should be a sticker which will have the pump model number. You can usually find this by the discharge port on the pump. Once you locate it you can choose the correct replacement motor. Be certain to change the shaft seal and gaskets as needed. You can use our >How to guide if you need help. 
 Reply


?     Asked on 1/19/2012by Guest

I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
 Reply

A  Answered on 1/19/2012 by InyoPools Product Specialist Patrick P.

Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
 Reply


?     Asked on 3/22/2015by Inyo Visitor

What is the speed for this motor?
 Reply

A  Answered on 3/23/2015 by InyoPools Product Specialist Robert M.

The USN1202 is a single speed motor. The RPM's are 3450.
 Reply


?     Asked on 3/24/2015by Inyo Visitor

I would like to order the 2-speed version of this motor. Thanks
 Reply

A  Answered on 3/25/2015 by InyoPools Product Specialist Robert M.

Part number SPX1615Z2MNS is the 2-speed version of this motor.
 Reply


?     Asked on 4/2/2015by Inyo Visitor

I have a 3 HP northstar pump with AO smith motor. Can it be replaced with a 2 HP motor and matching impeller (i.e 2 HP rated impeller)?
 Reply

A  Answered on 4/3/2015 by InyoPools Product Specialist Lennox H.

Yes, you can. The motor USN1202 and the impeller kit 5112-026.
 Reply


?     Asked on 5/19/2015by Mike

Will this replace my Hayward northstar sp1615z1mnsc?
 Reply

A  Answered on 5/19/2015 by InyoPools Product Specialist Andy O.

Mike- The A.O. Smith 2 HP Up Rated Northstar Replacement Motor (USN1202) will be a replacement for your Northstar pump, I would also recommend that you get the shaft seal for your pump so that you don't leak and void the motor warranty. The seal you would want is , 5112-216 (SPX3200SA), or you can get the salt water seal, 5250-250 (PS-4280).
 Reply


?     Asked on 9/16/2015by Red

Would you recommend purchasing the seal tune up kit or just the heavy duty shaft seal (5250-250 (PS-4280)) when replacing this motor for a salt water pool? What is the part number for the seal tune up kit for this model pump?
 Reply

A  Answered on 9/21/2015 by InyoPools Product Specialist Lennox H.

Hi Red, The Heavy Duty Shaft Seal (PS-4280) would be the recommended choice to use in a salt water pool. There is only a Tune Up Kit for the 200-2007 Hayward North Star model not the 2008-current model. The PS-4280 can only be used on the 2008-current models, you would havr to purchase the seals separately.
 Reply


?     Asked on 2/27/2016by Fred

What is the start capacitor part number for this motor?
 Reply

A  Answered on 2/29/2016 by InyoPools Product Specialist Megan C.

Hello Fred - The USN1202 only has a run capacitor. The part number is 5270-02.
 Reply

  • Commented on 6/10/2020 by Product Owner

    I am confused as to why this is a "run" capacitor as opposed to a "start" capacitor as when they go bad the motor hums but will not start. I have replaced a few of these on my USN1202 under this exact circumstance. I can always start and "run" the motor with a bad capacitor while awaiting delivery of a new capacitor by abruptly turning the motor with a wrench while it's humming. Starts right up continues to run. So isn't this a "start" capacitor?
     Reply


?     Asked on 8/24/2016by Inyo Visitor

Warranty information?
 Reply

A  Answered on 8/26/2016 by InyoPools Product Specialist Lennox H.

Hi, This motor comes with a (1) year warranty from date of purchase.
 Reply


?     Asked on 1/14/2017by Inyo Visitor

looking for capacitor requirements for the AO Smith SP1615Z1MNSC motor Does it use the same capacitor size requirements as the usn 1202 listed above part 5270-02
 Reply

A  Answered on 1/16/2017 by InyoPools Product Specialist Adam Y.

On the capacitor you need there will be a number starting with UF or MFD. Find out what your number is.Type it in in the search bar at inyopools.com.
 Reply


?     Asked on 6/1/2017by mike

is the AO Smith USN 1202 the same as the Hayward SPX1615Z1MS? I have a Hayward Northstar 2HP pool pump model # SP4015X20NS, and I wanted to replace the motor. I notice you carry both motors but the AO Smith is cheaper. If it's really the same motor and will work just as well than I will order the AO Smith.
 Reply

A  Answered on 6/2/2017 by InyoPools Product Specialist Patrick P.

Hi Mike, Yes the USN1202 is the same motor and will work just as well. Go with the USN1202.
 Reply


?     Asked on 6/9/2017by allison

I need a replacement for my Hayward northstar sp4015x20ns pump, also need a motor shaft seal, gasket diffuser and plastic o ring. I see that the A.O. Smith USN 1202 is a suitable replacement for the motor, but how do I make sure I order the seal, gasket diffuser and plastic o ring correctly, to fit the a o smith?
 Reply

A  Answered on 6/11/2017 by InyoPools Product Specialist Lennox H.

Hi, Allison. The Century USN1202 Motor is the correct replacement, however, you will need to know when the pump was manufactured in order to locate the correct seals. If you can locate the housing serial number and call Hayward @ (908) 355-7995.
 Reply


?     Asked on 6/21/2017by Jonas

Hi, I currently have this pump motor, but I want to replace the entire pump and motor, will the SP2615X20 work?
 Reply

A  Answered on 6/21/2017 by InyoPools Product Specialist Patrick P.

Hi Jonas, normally the USN1202 is used on a Hayward Northstar Pump and if that is the pump you have then the Hayward SP2615X20 2 HP Pump would be a good replacement. I also really like the PL2603 PureLine Prime 2 HP Pump as it has 2" plumbing connections vs. the smaller 1.5" ports on the Super Pump. Either way you go you will have some slight re-plumbing as the plumbing ports on the pumps are not in the exact same location.
 Reply


?     Asked on 2/5/2018by JASON CHOI

my pool pump motor label showed: Part 7-187582-02 serial: CB01-31 the rest looks the same, DO YOU THINK IT'S THE SAME MOTOR?
 Reply

A  Answered on 2/5/2018 by InyoPools Product Specialist Lennox H.

Hi, Jason. This USN1202 is the correct replacement. 
 Reply


?     Asked on 5/11/2018by Mike Anderson

My current motor is a O.A.Smith SP1615Z1MNSC, SF1.2, & Y56J frame. The serial number is 229093M. Is this AO Smith USN1202 the exact replacement? And what kit would be required? The motor is about 4 years old and the pump is about 15 years old
 Reply

A  Answered on 5/12/2018 by InyoPools Product Specialist Alex V.

Mike, The USN1202 is the correct replacement for the SP1615Z1MNSC. In order to recommend the shaft seal, we will need to know the pump model. 
 Reply


?     Asked on 5/12/2018by Lana

I have an A.O. Smith CAT- USN1202 / SERIAL 082093M / PART 7-193687-02 / TYPE CX / FR Y56J / HP 2.0 / SF 1.20 / HZ 60 / RPM 3450 / VOLTS 208-230/115 / AMPS SF 11.0-10.2/20.4 When we had a leak in the housing we were told that this pump had been discontinued. We found a replacement housing a few months back, but it has died today. We need to replace the whole unit and need to know which replacement to get?
 Reply

A  Answered on 5/13/2018 by InyoPools Product Specialist Hector F.

Based on the motor model you have a Northstar so you can replace that model pump with the Tristar model SP3215EE
 Reply


?     Asked on 5/12/2018by Mike Anderson

Thanks for the quick answer re: the pump motor. The pump itself is a Hayward SP4015X20 with SER#21110908050927008. Are you able to tell the age from that or do I need to contact Hayward?
 Reply

A  Answered on 5/13/2018 by InyoPools Product Specialist Lennox H.

Hi, Mike. Your pump was manufactured in August 2009.  
 Reply


?     Asked on 5/17/2018by Tony

My Hayward Pump Motor 7-187582-02 (AO Smith motor) is humming but the impeller is not moving / pulling water in. How do I check the capacitor on this model?
 Reply

A  Answered on 5/18/2018 by InyoPools Product Specialist Hector F.

We created a guide for checking a capacitor that you can view by clicking here
 Reply


?     Asked on 7/25/2018by Eddie Worthington

Does the pump SPX1615Z1MNS come with defuser-o ring( s) - impeller
 Reply

A  Answered on 7/25/2018 by InyoPools Product Specialist Lennox H.

Hi, Eddie. It does not, those parts are sold separately. They are listed on the Hayward Northstar Pump Part Page. 
 Reply


?     Asked on 9/19/2018by Frank sr

Would this replace a Hayward northstar 2hp sp1815-z1-mnsc motor?
 Reply

A  Answered on 9/26/2018 by InyoPools Product Specialist Lennox H.

Hi, Frank Sr. This is the correct replacement for the NorthStar SP1615-Z1-MNSC motor. 
 Reply


?     Asked on 1/20/2019by Jeff

Hi I have a Hayward Northstar 2.00HP pump. The fully assembled pump has a model of SP4015X20. The motor on it is bad. I want to replace the motor. The motor has a part number of SP1615Z1MNSR (see screenshot). I can't find that exact part number on your site but the closest is your SPX1615Z1MNS item. That item says it has alternate part numbers of SP1615Z1MNS and SP1615Z1MNSC.... both of which are similar but missing the "R" at the end like my model. What's the difference and will it fit?

 Reply

A  Answered on 1/21/2019 by InyoPools Product Specialist Lennox H.

Hi, Jeff. This USN1202 motor is the correct replacement motor. It will fit your model pump. 
 Reply


?     Asked on 1/21/2019by Chad

My SP4015X20NS model Northstar has serial ID 21110509050127007. Can you please tell me what year this was made? Is this the correct motor for replacement? What else should I replace when I replace the motor? Diffuser, Diffuser O ring, Impeller assembly....anything else?
 Reply

A  Answered on 1/22/2019 by InyoPools Product Specialist Lennox H.

Hi, Chad. Your model pump was manufactured in September of 2005. This USN1202 is the correct replacement motor. As for the other parts, they are all listed on the Hayward Northstar Pump 1998 to 2007 Parts Diagram
 Reply

  • Commented on 1/23/2019 by Product Owner

    Could I upgrade to the full rate pump without issue? I confirmed that what you listed is the model I have but it has a really hard time running the skimmer and vacuum at the same time. I have to keep both at about half intake at the valves. A hair extra power would be nice.
     Reply

    • Commented on 1/24/2019 by InyoPools Product Specialist Lennox H.

      Hi, Chad. You can upgrade the motor; however, you will have to upgrade the impeller as well in order to get the benefits. 
       Reply

      • Commented on 1/24/2019 by Product Owner

        What part is the upgraded impeller?
         Reply

        • Commented on 1/30/2019 by InyoPools Product Specialist Lennox H.

          Hi, Chad. Part # SPX4020CKIT is the nest size up impeller. You will need to use Motor # SPX1620Z1BNS
           Reply


?     Asked on 4/9/2019by Dennis

Need a replacement motor for my Hayward North Star pump....Let me Know everything I need so I can purchase everything at once...No need to skimp and have problems down the road....Thx guys...

 Reply

A  Answered on 4/9/2019 by InyoPools Product Specialist Lennox H.

Hi, Dennis. This is the correct replacement motor for your pump. You will also need to replace the seals will be specific to which version NorthStar Pump you have which you can use our NorthStar Pump Parts Page
 Reply


?     Asked on 4/15/2019by Debbie Robinson

I have a Hayward Northstar Pump /A. O. Smith Model SP4015x20 SP1615Z1MNSC Part#7-187582-02 S/N 21110908050219004 Is the USN1202 the correct replacement motor and what shaft seal or impeller kit do I need and does the kit include shaft seal? Also, what is the age of my pump?

 Reply

A  Answered on 4/15/2019 by InyoPools Product Specialist Lennox H.

Hi, Debbie. This USN1202 is the correct replacement motor. You will need the Impeller Kit - SPX4015CKIT or the Pump Shaft Seal - SPX4000SA2 (OEM), PS-3890 (Generic), or PS-4280 (Heavy Duty). Your pump was manufactured in August 2009. 
 Reply


?     Asked on 6/16/2019by jeffrey Carugati

I have a Hayward Northstar pump that is used on my spa pumps. This pump is humming and needs to be replaced.The current motor is sn1202 2 hp motor. Does it make any sense to upgrade to 2 1/2 hp motor for more water flow when the spa is on? I have 2" piping.
 Reply

A  Answered on 6/19/2019 by InyoPools Product Specialist Matt S.

If the water flow was fine before, then I would stick to the same horsepower motor and setup you currently have. The page for your motor is the SN1202 - 2 HP Full Rate NorthStar
 Reply


?     Asked on 2/4/2020by michael troche

Hi I want to replace my current engine. This was not the original engine with my Northstar pump but it worked fine until it went. I want to reorder a tune up kit and new empeller also. Can you confirm that USN1202 will work on my hayward and also the correct gasket seals and tune ups etc.

 Reply

A  Answered on 2/4/2020 by InyoPools Product Specialist Lennox H.

Hi, Michael. This USN1202 is the correct replacement for the motor in the picture provided. As for the Impeller Kit, the P/N is SPX4015CKIT. We will need to know the age or pump style you have in order to determine if the NorthStar 4000 Series Pumps (Pre-2003) Tune Up Kit - GOKIT66 will work with your pump. 
 Reply

  • Commented on 2/4/2020 by Product Owner

    We cant get that from the pic?
     Reply

    • Commented on 2/6/2020 by InyoPools Product Specialist Lennox H.

      Michael, Unfortunately, not. The pump serial number and or a picture of the housing is needed. 
       Reply


?     Asked on 2/9/2020by Edward Svihla

I installed the USN1202 motor in June 2018, and it sounds like the bearing are going bad already. Any recommendations?

 Reply

A  Answered on 2/10/2020 by InyoPools Product Specialist Lennox H.

Hi, Edward. You can either replace the Bearings (1) 62032RS and (1) 63042RS or replace the motor. Bearings usually fail from water damage. 
 Reply

  • Commented on 2/10/2020 by Product Owner

    If I buy a new motor, what can I do to protect it? Over 40 years with houses with pools, I have never had a motor last less than 10 years. Imagine my disappointment when this one only lasted 18 moths.
     Reply

    • Commented on 2/11/2020 by InyoPools Product Specialist Lennox H.

      Edward, Keep the area dry and clean. 
       Reply


?     Asked on 5/3/2020by Steve

Why does this motor have "Northstar" in the title? Could I use any 2HP that has a round frame? Thank you.
 Reply

A  Answered on 1/7/2021 by InyoPools Product Specialist Hector F.

Hi Steve, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest provide them using our live online chat feature. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 10/31/2020by Leonard Adams

doese this motor have a capacitor for start or run?
 Reply

A  Answered on 11/2/2020 by InyoPools Product Specialist Hector F.

Hi Leonard, so this motor has a run capacitor part number 5270-02
 Reply


?     Asked on 8/28/2023by Chris Lowicki

Do you have the impeller and seals for this motor?
 Reply

A  Answered on 8/28/2023 by InyoPools Product Specialist Craig C.

Hello Chris.  Unfortunately, the impeller/seal kit SPX4015CKIT is currently not available through INYO Pools.  This item has been discontinued by the manufacturer and is no longer available.
 Reply