?     Asked on 1/11/2012by Guest

What is Service Factor?
 Reply

A  Answered on 1/11/2012 by InyoPools Product Specialist Patrick P.

Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
 Reply


?     Asked on 1/12/2012by Guest

Why do I need to purchase a new shaft seal?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
 Reply


?     Asked on 1/12/2012by Guest

Why should I purchase a Tune Up Kit?
 Reply

A  Answered on 1/12/2012 by InyoPools Product Specialist Patrick P.

A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
 Reply


?     Asked on 1/19/2012by Guest

I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
 Reply

A  Answered on 1/19/2012 by InyoPools Product Specialist Patrick P.

Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
 Reply


?     Asked on 2/16/2012by Guest

I just finished replacing the shaft seal on my booster pump. As soon as I turned the pump on water was leaking from the shaft seal. Is it defective or am I doing something wrong?
 Reply

A  Answered on 2/16/2012 by InyoPools Product Specialist Patrick P.

Depending on the model, the installation of a booster pump shaft seal can be slightly different than a pool pump shaft seal. Some booster pump and pool pump shaft seals require that a silicone sealant be used on the outer areas of the metal seat of the shaft seal. The seal will need to be lightly hammered into the body of the pump. You can use a 1 inch PVC coupling or a piece of 1 1/4 inch PVC pipe and a rubber mallet. This procedure will apply to any pool pump or booster pump using a >PS-1000 style shaft seal.
 Reply


?     Asked on 4/26/2015by Fred

Is this a new pump or rebuilt?
 Reply

A  Answered on 4/26/2015 by InyoPools Product Specialist Patrick P.

Hi Fred, This is a brand new motor with the full 1 year manufacture warranty.
 Reply


?     Asked on 3/7/2016by JOANNE WEBSTER

I NEED A NEW MOTOR AND GOT THE FOLLOWING #'S OFF THE OLD ONE. MOTOR#K48L2PA105, MODEL#AE100FLL. CAN YOU TELL ME IF THIS IS FOR THE MOTOR SHOWING ON YOUR WEBSITE WHEN I PUT IT IN. IT DOESN'T ACTUALLY SHOW THIS #
 Reply

A  Answered on 3/7/2016 by InyoPools Product Specialist Andy O.

Hello Joanne, The QC1102 1.0 HP Full Rate EE Motor (B864SE) would be the replacement for your K48L2PA105/ AE100FLL motor. Both of those numbers can be found in the Alternate Part#'s section of the product details.
 Reply


?     Asked on 5/10/2016by Rog

Water got into the motor and rust formed on the inside of end cap of the motor,right where the motor shaft come through to impeller. Do you know where I can get new end cap? Bearing and everything else is OK! Thank you R
 Reply

A  Answered on 5/13/2016 by InyoPools Product Specialist Lennox H.

Hi Rog, The Shaft End Bell (SAW-49) can be used with the QC1102 motor.
 Reply


?     Asked on 5/29/2016by Cory

I'm replacing my 20year old K48L2PA105 motor. Does this replacement come with a new shaft seal? If not, what is the part number. Thank you
 Reply

A  Answered on 5/30/2016 by InyoPools Product Specialist Alex V.

Cory, The motor does not come with a shaft seal. The seal is dependent on the make and model of the pump housing not the motor.
 Reply


?     Asked on 6/6/2016by Vee

Intermittently working k48l2pa105, is there a capacitor to swap or just move forward with this motor for replacement?
 Reply

A  Answered on 6/7/2016 by InyoPools Product Specialist Patrick P.

Hi Vee, Here is the Run Capacitor for your k48l2pa105 Motor and here is the Start Capacitor for your k48l2pa105 Motor
 Reply


?     Asked on 9/3/2016by John

Tune Up Kit Starite P4E & P4EA Max-E-Glas II / DuraGlas II GOKIT38 Is this the correct tune up kit for the 1.0 HP Full Rate EE Motor (B864SE) QC1102
 Reply

A  Answered on 9/16/2016 by InyoPools Product Specialist Lennox H.

Hi John, The GOKIT38 is the correct kit if you have a Sta-Rite Max-E-Glas II & DuraGlas II pump. The motors info does not determine which kit you needed.
 Reply


?     Asked on 10/7/2016by Inyo Visitor

What the difference between this model and "1 HP Motor EE - Full Rate (B2841, B2841V1)"? I have a Pentair Whisperflo WF-26 / 011773 / 1.5 HP / 1.65 S.F. HP. Which one should I buy? Thnx,
 Reply

A  Answered on 10/10/2016 by InyoPools Product Specialist Lennox H.

Hi. The difference between the QC1102 and the B2841 motors are the Frame size. The QC1102 has a 48Y frame which is smaller than the B2841 which has a 56Y frame. Either motor is compatible with  Pentair Whisperflo WF-26. The Pentair Whisperflo Tune Up Kit GOKIT32 or GOKIT32SALT is the correct kit for that pump.
 Reply


?     Asked on 7/8/2017by Inyo Visitor

What is the energy usage difference between the older qc1102 and the ee b864se?
 Reply

A  Answered on 7/12/2017 by InyoPools Product Specialist Lennox H.

Hi. The Century B864SE Motor has been replaced by the Century QC1102 motor. The B864SE used 7.8-7.4/14.8 amps at 208-230/115 volts and the QC1102 motor uses 8.0/16.0 amp at 208-230/115 volts. 
 Reply


?     Asked on 7/10/2017by Inyo Visitor

I have an A O Smith motor K48L-2PA105. What are the replacement bearings for this motor and are they the same for (SE) & (OSE)?
 Reply

A  Answered on 7/13/2017 by InyoPools Product Specialist Lennox H.

Hi. The K48L2PA105 motor uses the 203 Bearing on the SE and OSE
 Reply


?     Asked on 5/29/2018by Inyo Visitor

Is this compatible with the Sta-Rite P6EA6G-207L?
 Reply

A  Answered on 5/29/2018 by InyoPools Product Specialist Lennox H.

Hi. That pump model requires the USQ1202. You can convert that pump to use this QC1102 which will require changing the impeller and diffuser along with the seals. 
 Reply


?     Asked on 8/13/2018by Keith DeLong

This looks like the replacement for my K48L2PA105C3 in my sta-rite max-e-pro. Is there a variable speed motor that matches this one that I could upgrade to? what seal kit do I need?
 Reply

A  Answered on 8/17/2018 by InyoPools Product Specialist Lennox H.

Hi, Keith. You can use the ECM16SQU - 1.65 HP Variable Speed Square Flange Motor and the Sta-Rite Max-E-Pro Tune Up Kit - GOKIT79 are the parts you'll need to upgrade your current pump. 
 Reply


?     Asked on 10/20/2018by Jeff Dokousian

A.O. Smith pump Mod. K48L2PA101A1 finally died. I am looking to upgrade to one of the variable speed motors. Can you tell me what pump and seal kit (If needed) would be ideal for me please?

 Reply

A  Answered on 10/25/2018 by InyoPools Product Specialist Hector F.

The VS motor replacement that you would need is the model ECM16SQU. And for the seal kit, you will need to provide us with the model name or number of the front pump housing that the motor bolts to so we can cross-reference those seals. If you cannot locate that information then you can always send us an image of that to upload@inyopools.com so we can assist. 
 Reply


?     Asked on 3/19/2019by khoa

what is the replacement bearings for this motor?
 Reply

A  Answered on 3/19/2019 by InyoPools Product Specialist Lennox H.

Hi, Khoa. The 62032RS Bearing are the correct size for the SE and OSE for the QC1102 motor. 
 Reply


?     Asked on 6/3/2019by JOHN JANUS

can you ship A.O. Smith 1 HP Square Flange 48Y Full Rate EE Motor - QC1102 to california?
 Reply

A  Answered on 6/3/2019 by InyoPools Product Specialist Patrick P.

Unfortunately, we cannot, you would need this 1.65 HP Variable Speed Replacement Motor.
 Reply


?     Asked on 6/12/2019by Inyo Visitor

Is this the right pump?

 Reply

A  Answered on 6/12/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this is the correct replacement.
 Reply


?     Asked on 6/12/2019by Inyo Visitor

is this the right motor?

 Reply

A  Answered on 6/12/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this is the correct replacement. 
 Reply


?     Asked on 7/28/2019by Charles Bihler

Hi we are ordering a pool motor ao smith 1 hp glance 487 qc1102 do we need to order anything else for the installation .....ie like a sleeve
 Reply

A  Answered on 7/28/2019 by InyoPools Product Specialist Lennox H.

Hi, Charles. You will need to replace the pump shaft seal. To locate the correct replacement, you will need to provide us with the pump housing pump model.
 Reply


?     Asked on 11/4/2019by Dave

Need to replace my filter motor and received advice on your Chat line that is the proper replacement motor. Old motor is Max-E Glas II Model K48L2PA105 and seal plate has numbers P4E6E-151L. Is it also necessary to replace the seals on the pump housing/seal plate?
 Reply

A  Answered on 11/4/2019 by InyoPools Product Specialist Lennox H.

Hi, Dave. You will need to replace the seals, the Max-E-Glas II / DuraGlas II Tune Up Kit - GOKIT38 is the correct kit. 
 Reply


?     Asked on 1/28/2020by Inyo Visitor

How critical is it for water to travel from pool to heater and back to raise temp, both pumps are 2" in and out with 3450 RPM`s with same voltage, except one was a older 2HP and the new one is 1hp with a 1.65 s.f.
 Reply

A  Answered on 1/29/2020 by InyoPools Product Specialist Lennox H.

Hi. It is very critical to ensure that the unit functions properly and as intended. Heaters will not work without the proper water flow. 
 Reply


?     Asked on 4/18/2020by Tovias Aguiniga

Why can't you send this m,otor qc1102.
 Reply

A  Answered on 12/22/2020 by InyoPools Product Specialist Hector F.

Hi Tovias, if you live in the state of California then the reason why we cannot ship this motor there is due to the California Title 20 law
 Reply


?     Asked on 4/18/2020by Tovias Aguiniga

Why is this motor nmot allowed in Galifornia QC1102.
 Reply

A  Answered on 11/6/2020 by InyoPools Product Specialist Hector F.

Hi Tovias, so there have been energy-efficient laws passed in the state of California regarding pool pumps. Here is a blog article that we put together that better explains those details called "California’s New Variable Speed Pool Pump Law"
 Reply


?     Asked on 7/26/2020by Jeff

Hi there, I have a 1HP k48l2pa105. Is this the one? Do I need to also upgrade impeller as well? my pump is a STA-RITE pump if that helps. Thanks in advance! Jeff
 Reply

A  Answered on 11/13/2020 by InyoPools Product Specialist Hector F.

Hi Jeff, this is the correct single speed replacement motor for the motor model k48l2pa105. You should not need to upgrade the impeller. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply


?     Asked on 8/20/2020by Kyle Riddle

I need a motor for my spa this is the Model number what can I replace it with. K48M2N118A2
 Reply

A  Answered on 8/20/2020 by InyoPools Product Specialist Lennox H.

Hi, Kyle. The Century 1.5 HP Round Flange 56J Dual Speed Full Rate Motor - STS1152R is the correct replacement for the model # provided.
 Reply


?     Asked on 8/20/2020by Kyle Riddle

Here are pictures of the motor I need. Please advise

 Reply

A  Answered on 8/20/2020 by InyoPools Product Specialist Lennox H.

Hi, Kyle. The Century 1.5 HP Round Flange 56J Dual Speed Full Rate Motor - STS1152R is the correct replacement for the motor you have.
 Reply

  • Commented on 8/20/2020 by Product Owner

    I have told you twice and sent pictures the one you recommend is a round flange you can clearly see in the pictures mine is a square flange, would the 1 hp square flange 48y Full Rate EEmotor QC1102

     Reply

    • Commented on 8/27/2020 by InyoPools Product Specialist Lennox H.

      Kyle, The Motor Mounting Plate - SPX1600F5 is different from the Motor Flange. The STS1152R Dual Speed Motor or the ST1152 Single Speed motor are your options. 
       Reply


?     Asked on 9/10/2020by huong le

my pond pump is A.O smith model K48L2PA101A1; QC1102 1 HP is dead. I need the same one to replace, and a seal or something else for that Thank you so much.
 Reply

A  Answered on 12/17/2020 by InyoPools Product Specialist Hector F.

Hi Huong, yes this is the correct single speed replacement motor for your motor model K48L2PA101A1. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply


?     Asked on 5/2/2021by Daniel Robinson

Is the QC1102 a replacement for a AE100EHL motor? If so is it in stock and how long to ship?
 Reply

A  Answered on 5/3/2021 by InyoPools Product Specialist Danny R.

Daniel,Yes, the QC1102 pool pump motor is a replacement for the AE100EHL pool pump motor.  It is currently in stock and we typically ship our motors within 24 hours.  We do not want you to have a green pool :)
 Reply


?     Asked on 11/28/2021by Brad Shirhall

I'd like to use this as a replacement for the motor on my original Sta-Rite P6E6E-206L, also an SF1.65 1HP motor. Appears as a direct replacement for the K48L2PA105 motor. Please confirm this is compatible? Do you sell the seal kit to go along with this? Thank you
 Reply

A  Answered on 11/29/2021 by InyoPools Product Specialist Stephen B.

Thank you for Contacting Inyo Pools, Century 1.0 HP Square Flange 48Y Full Rate Motor - SQ1102 should be the correct replacement motor. I'm going to need a serial number from the pump housing. There are different seal plate o-rings after pre and after 2015. If you could send some photos of the pump and motor so can we can verify.
 Reply

  • Commented on 11/29/2021 by Product Owner

    Thx for the quick response. SN: 034Q06L Unit was installed in 2006. Pictures of seal pack; inside of flange; impeller; included.

     Reply

    • Commented on 12/1/2021 by InyoPools Product Specialist Megan C.

      The motor mentioned above or the Century 1.0 HP Square Flange 48Y Full Rate EE Motor - QC1102 with Tune Up Kit Sta-Rite Max-E-Pro (Pre February 2015) - GOKIT79 If you use a salt system to generate chlorine add the Pump Seal 201, Extra Heavy Duty PS3868 (Saltwater Pools) - PS-3868 with the Gokit79. Sta-Rite Max-E-Pro Pump parts page https://www.inyopools.com/pool_parts_sta_rite_max_e_pro_pump.aspx 
       Reply

      • Commented on 12/2/2021 by Product Owner

        Well - I got shut down on my order because the Governor of California doesn't like that pump!! Conceivably the Century SQS1102R is an acceptable alternative for my A.O Smith K48L2PA 105 SN:034Q06L. Please confirm. I'll also get the seal package and might as well get the dual speed toggle too. Ironically I live in a city with some of the cheapest electricity in all of California. Such is life!
         Reply

        • Commented on 12/3/2021 by InyoPools Product Specialist Megan C.

          Yes, the Century 1.0 HP Square Flange 48Y Dual Speed Full Rate Motor - SQS1102R with End Cover Switch Assembly - 1011431-001 and Tune Up Kit Sta-Rite Max-E-Pro (Pre February 2015) - GOKIT79 If you use a salt system to generate chlorine add the Pump Seal 201, Extra Heavy Duty PS3868 (Saltwater Pools) - PS-3868 with the Gokit79 is suggested. Please note, the dual-speed motor is for 230V only. How To Use a Multimeter to Test a Pool Pump Motor - Voltage
           Reply


?     Asked on 1/14/2022by Dennis

I need to replace a Century SQ1102 motor. Are there upgrade options that are quieter?
 Reply

A  Answered on 1/14/2022 by InyoPools Product Specialist Rich N.

Hi Dennis, the single-speed motors all drone on to one extent or another, but many people find that the variable-speed motors are quieter than the regular single-speed motors, especially if you turn the speed down from the maximum.  This V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU would be a perfect replacement for your old SQ1102 and it could also pay for itself over time as long as you set it up correctly.  Your local city or utility company may offer a rebate for the purchase price of it as well.  
 Reply

  • Commented on 1/14/2022 by Product Owner

    Rich, My apologies. I sent the incorrect motor information. Here is a picture of the motor that needs to be replaced, and is there a more efficient upgrade for this one?
     Reply


?     Asked on 5/5/2022by David Reilly

is this the match for sta- rite, AO Smith P6E6E-206L,1HP,serial #035B08X
 Reply

A  Answered on 5/5/2022 by InyoPools Product Specialist Craig C.

Hello David.  The Century 1.0 HP Square Flange 48Y Full Rate EE Motor - QC1102 is compatible with the Pentair/Sta-Rite Max-E-Pro Pool Pump model P6E6E-206L.  The Tune Up Kit Sta-Rite Max-E-Pro (Pre February 2015) - GOKIT79 contains the seals and gasket necessary to complete the new motor installation.
 Reply


?     Asked on 9/1/2023by Jack Strollo

Can I switch this out for a variable speed or do I need to change the whole pup to do that?
 Reply

A  Answered on 9/1/2023 by InyoPools Product Specialist Jacob F.

You can switch out your current motor for a variable-speed unit, and you would be able to keep your current wet end housing. The recommended variable speed upgrade for your motor would be the Century (A.O. Smith) V-Green EVO 1.65 HP Up Rate VS Motor, Square Flange 48Y Frame, Variable Speed - Model EVQ165
 Reply