What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
Can you direct me to the proper hi low switch for this motor?
Reply
Unfortunately the manufacturer does not offer the switch for the 2 speed 220v motors any longer. If you already have a 220 volt timer (on/off) you would need an Intermatic T106R to switch from high to low speed. If you do not have a timer currently you would need the T10604R which is a 220v on/off timer and a high/low timer.
Reply
How can I tell whether or not my motor is a dual or single speed?
Reply
Most dual speed motors will have a toggle switch that will allow you to adjust the motor speed to either high or low. Another way to tell if your motor is dual speed is by looking at the RPM's on the motor specifications label. If there are two RPM's listed such as: 1725/3450 then motor is dual speed. If there is only one RPM, then motor is single speed.
Reply
I'm trying to replace the motor on my pool pump but all these numbers and abbreviations on the motor label are really confusing me. What do they mean?
Reply
Replacing a pool pump motor is not as difficult as it seems. You can try looking here. If you need help figuring out what the information on your label means. If you are still having difficulty figuring it out you can call us at our toll free number or you can send us a photo of your motor label here.
Reply
I just finished replacing the shaft seal on my booster pump. As soon as I turned the pump on water was leaking from the shaft seal. Is it defective or am I doing something wrong?
Reply
Depending on the model, the installation of a booster pump shaft seal can be slightly different than a pool pump shaft seal. Some booster pump and pool pump shaft seals require that a silicone sealant be used on the outer areas of the metal seat of the shaft seal. The seal will need to be lightly hammered into the body of the pump. You can use a 1 inch PVC coupling or a piece of 1 1/4 inch PVC pipe and a rubber mallet. This procedure will apply to any pool pump or booster pump using a >PS-1000 style shaft seal.
Reply
I have a 1.5 hp Sta-Rite Duraglas H/L spa pump that a motor repair specialist deemed to old to rebuild. I think the H/L stands for high/low as it is a two speed. This is an AO Smith motor with what I believe is a model number P2R-A5YF 125. Is the one listed the pump I need to replace my old one? Will the impeller, difuser etc. attach to it?
Thanks for your help, hope to place an order with you if I can match a replacement.
Reply
Good morning Harley, If the hp on your pump is the original 1.5hp you will need a A.O. Smith 1 1/2 H.P Square Flange Up Rate Motor - USQ1152 You will also need to replace the shaft seal and possibly the o-rings (seal plate and diffuser). You can get all of those in a Tune Up Kit Sta Rite Dura Glas & Max E Glas Pump 1998 To Present - GOKIT54
Reply
Hi, I have century two motor w/ plate:
PART: 8-177456-03
TYPE: CXPM
FR: Y56Y
HZ: 60
RPM 3450/1725
AMPS: 10.0/3.5
TIME: CONT
ENCL: DP
FORM: KJM
CODE K
1081 POOL PUMP DUTY MOUNT 071320
Is this the right motor for replacement? Can I also purchase the maintenance parts here?
Thank you very much in advance.
Reply
That would be the correct replacement motor but to determine the correct shaft seal you need for the motor replacement I need to know the model of your pump. If you are not aware, please attach a picture of your complete pump so I can identify it for you.
Reply
Q: Hi, I have a Pentair WhisperFlo pump WFEDS-6 with century two speed motor w/ plate:
PART: 8-177456-03 TYPE: CXPM FR: Y56Y HZ: 60 RPM 3450/1725 AMPS: 10.0/3.5 TIME: CONT ENCL: DP FORM: KJM CODE K 1081 POOL PUMP DUTY MOUNT 071320
Is this the right motor for replacement? Can I also purchase the maintenance parts here?
Thank you very much in advance.
A: That would be the correct replacement...
Q: I have replied your email with pictures see if you can get that. Thank you.
Reply
My current pump is a square flange 48y frame ao smith pump. Can this pump replace my old one? I want to go from single speed to dual speed.
Reply
Hi, A 56Y frame motor can be used to replace a 48Y frame motor. To ensure that we get you the correct dual speed replacement, please provide your pump or motor model number or photos.
Reply
My Motor is a Century Pool & Spa Motor, Dual Speed Power Saver, Smart Max Starpump
Part #: 7-K56AA23A04-05 Model # SP3210Z2ME Serial # 066113M FR Y56Y Type CXCP
RPM: 3450/1725 Volts: 208/230 HP: 1.5hp/.19 SF: 1.23 Time: Cont AMPS: 8.5/1.5
Do you have a motor that is a direct replacement for this motor and if you do, what would be the complete cost shipped to Gulf Shores, Alabama. Thanks John P Kendall
Reply
Hi, The Hayward 1-1/2hp Maxrate 2-speed Motor - SPX3210Z2MER is the direct replacement for the pump you have according to the info provided.
Reply
I am looking for a replacement pump motor for a built-in hot tub. The old pump is a Pentair WhisperFlo #PMP WFE-6 20/-230 Volt 1.5 HP, Built in 2010, Century Centurion Cat. # B2858, FR Y56Y, SF 1.50, Type CX, 10.5 Amps, 3450 RPM. I also need the seal and tune-up kit for the replacement. And a replacement Timer for the unit. Can you help me find these parts?
Reply
I have a Century B983 dual speed pool pump. Can the motor be replaced with a compatible variant speed pump motor?
Reply
Yes the ECM27SQU 2.7 HP Variable Speed Motor would be the motor you require. To take advantage of the higher HP range of this 2.7 HP motor you may want to swap out your impeller to a larger impeller.
Reply
I bought a dual speed 1.5 hp B2983, B983 and was told in a Q&A that there was A SWITCH to change from hi to low speed i am unable to find the switch on the motor I received. How do you change from hi to low without changing the wiring.
Reply
Hi, David. Unfortunately, the Toggle Switch and Canopy Kit - 2512558-001 is not included with the motor, it is sold separately.
Reply
I am looking to replace my current century Centurion BW3-7 1hp in ground pool pump. will this dual speed be sufficient?
Reply
Hi, Martin. This motor can be used as a replacement for a 1 hp single speed motor as long as the frame size is correct. This motor does not include a toggle switch 2512558-001, it's available separately.
Reply
Century B2983 motor
Do you have the wiring diagram for the capacitor connections?
Reply
Ben, The Century Pool and Spa Manual has the wiring diagram for the motors based on the motor type.
Reply
I have a Whisperflo Model WFE-6 pump, Century Centurion Part 7-177451-03 motor (60Hz, 3450 RPM, 208-230 V, 9.6-8.8 amps, Y56Y Frame). Are there issues with installing a two speed motor on a pump originally designed for a single speed motor? I anticipate doing general circulation at low speed and using high speed for our inground spa that overflows into the pool. I have a remote panel used to control the pump and heater. Can I use the panel to control the two speeds w/o the toggle switch? Thanks
Reply
Hi, Greg. A dual speed or single speed motor will mount to the same pump housing with no issues. If your controller can support a dual speed motor then it will control the motor, if not you will have to use the Canopy Toggle Switch - 2512558-001.
Reply
Is there a round flange version of this pump that only draws 1.6 amps on low speed?
I want one for my super pump. Thanks, Evan
Reply
We, unfortunately, do not a model motor that will match those specifications.
Reply
Part # 7-k56aa14a04-05 ao smith 2 speed pump. I have 2 timers one for low speed and one for high speed. Do I need the switch or will this just hook the same as the old one?
Reply
Hi, Robert. This replacement option will be wired the same way.
Reply
I currently have this pump and need to replace it. Mine has the digital control mounted to it, is that easy to put on this same motor?
Reply
Hi, Brian. Unfortunately, you're unable to remove the Digital Controller from the B2983T Motor and mount it to this motor. Your only options are to purchase the Toggle Switch and Canopy Kit - 2512558-001 or the Dual Speed Pump Timer - T106R.
Reply
I have a question about the differences between the B983 and the B2983 - other than price. I have a 7-193990-07 2hp up rated to 2.20HP
Reply
I currently have a century motor O-193989-05 will this replace it? 1.5hp 2 speed
Reply
Actually, the replacement motor is the model B2982.
Reply
but this is a 1hp and I currently have a 1.5
Reply
Hi. Motors are rated differently, Full Rate and Up Rate which is explained in our How to Replace Full Rated and Up Rated Motors, and Is a 1.0HP Motor the Same as a 1.5HP Motor?
Reply
i have a century dual speed model #193989XCN 1.5hp.
I see differences in total HP and RPM's and amps. I want to make sure i get the right pump
will this motor replace it?
Reply
I currently have a Hayward TriStar 2 speed pool pump with an Emerson motor model number R63CXDPY-233. There is another number above the model number which is SP3215Z2BER. I have attached a photo here.
Can you please recommend the appropriate replacement motor?
Thanks
Reply
Hi. Due to the total hp of this motor, the B2984 will be a more suitable replacement. The OEM motor is p/n SPX3215Z2BER which will have to be special ordered.
Reply
Is the B2983 the replacement motor for what I have? Also is there a gasket/seal kit to accompany it?
Hi, Robert. The SPX3210Z2MER OEM or this B2983 motor along with the Tristar Tune Up Kit - GOKIT81 are the parts you will need.
Reply
I have an AO Smith B858 that's decade(s) old - can I swap it out with this motor to upgrade to a dual speed model? Is there a variable speed option?
Thank you!
Hi. Yes, you can with this B2983 motor which will require a Toggle Switch - 2512558-001 or an external controller. The V-Green - ECM27SQU is the variable speed replacement option for the B848 motor you have.
Reply
Thank you for the speedy answer! Will I need anything additional if I go with the variable speed model you linked?
Reply
Yes, you will need to replace the pump seals. Please provide the pump housing model.
Reply
Hey Lennox, There aren’t any labels on the pump or filter basket. If I wanted to replace that as well, what would work with the variable speed motor?
Reply
Send me a picture of the pump housing so that I can make some recommendation.
Reply
I need to replace Century part 7-193990-07. Is this a suitable replacement? Thanks.
Reply
Hello, This will be a good replacement for you. http://www.inyopools.com/Products/00200017039438.htm
Reply
I currently have a Hayward Tristar Variable speed 1.5 (sp3210z2me) wanted to know if I could upgrade that motor? Or if it was even possible my my setup
Reply
Hi, Chris. The SP3210Z2MER motor model you have is a dual speed, which can be converted to a variable speed using the ECM16SQU.
Reply
I had a Magnetek Century 2 spd pool/spa Pump CatB985 Part 8-177070-07 Type CXPM. I have used several other pumps over the years but none have lasted. What is a good 2 spd 1.5HP pump for my inground pool 30,000 gallon pool
Reply
This B2983 replacement motor is a good dual speed replacement motor for your application.
Reply
I have a Jandy FloPro Model FHPM2.0-2 pump. The motor would click, but not start. I turned the pump off to begin troubleshooting. Before I could test the starting capacitor, the motor emitted light smoke when trying to start. I plan on replacing the motor. Is this motor the correct one for my pump. Also, do I need any additional parts?
Thank you.
I have a b2983 dual speed motor. Two questions. 1. What are the available options for replacement run capacitors (the one in the doghouse). 2. Is there any additional wiring needed to run the toggle switch?
Reply
Hi, Christopher. The Run Capacitor, Dual, 25 + 10 MFD / 370 VAC - 195662-25 is the correct replacement capacitor for the B2983 motor. No additional wiring is required to use the Toggle Switch - 2512558-001.
Reply
Thanks. That is the capacitor I have in order. I was just hoping there was another one that would work since it’s a 3 week delay in getting the part. Good to know about the toggle
Reply
have b293 motor on Jandy SPHF 1.5-2 pump... I am replacing motor, is there a tune-up kit also? thought while i had it apart would changes seals etc... thanks
Reply
Hi, Mike. There is not a kit available for your model pump, the seal will have to be purchased separately. They're all listed on the Jandy Stealth SHPF & SHPM Series Pump (2008-Current) Parts Diagram page.
Reply
My pump is making a clicking and then a humming noise and then stops. This is the label on my pump. Is this the correct replacement pump?
Hi, Scott. Yes, this B2983 is the correct replacement motor. You will also need the WhisperFlo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
Hi,
Is this the correct pump motor to replace my current one that is connected to a Hayward TriStar Hi Perf 2 speed
Century AO Smith Part# 7-K56AA14A04-05
See attached pics
Hi Tim, yes, this is the correct single speed replacement motor for the motor included in your photo. You will also need a Hayward Tristar seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
MY motor is seized and needs to be replaced. Is this the correct motor for a Jandy SHPM 2.0-2
Yes this is the correct replacement motor the motor included in your photo. When replacing your motor you will need a shaft seal can you supply us with the serial # from your pump this should be on a small label on the pump housing. The serial # is needed to suggest the proper shaft seal. Please click the reply link below to supply this information.
Reply
BTW, does it come with required gaskets? David
Reply
Hi David, No it does not. That is why I will need this information requested in the last comment, could you supply this to me? "When replacing your motor you will need a shaft seal can you supply us with the serial # from your pump this should be on a small label on the pump housing. The serial # is needed to suggest the proper shaft seal. Please click the reply link below to supply this information."
Reply
Looking for a like-replacement motor. Current specs:
Century 2-speed
Model # SP3215Z2BE
Hayward TriStar Model # SP32152EE, full rated pump.
1.5HP
SF 1.6
60Hz
RPM 3450/1725
Serial # 27013J2
Part # 7-K5AA14A04-05.
I see the B2983 motor as a possible but i'm concerned the SFxHp is below my current motor (2.2 vs 2.4). Also, I also need a Tune Up Kit?
Reply
Hi Chris, This is NOT the correct replacement for you. You will need this SPX3215Z2BER 1.5 HP TriStar Full Rate Dual Speed Motor you will also require this Hayward TriStar Seal Kit.
Reply
Hello, my pump stopped working & i would need to purchase all necessary parts to replace. Could you please provide me with more information in if this specific pump is a replacement and what exact seals or parts are needed. Thanks in advance!
Hi Carlos, This B983 motor is the correct motor for your Jandy Flo Pro Pump in your photos. You will also need this Jandy Flo Pro Shaft Seal
Reply
Hello patrick, thank you for your information that you procided. Question, Would “Century 3.0 HP Square Flange 56Y Full Rate EE Motor - B2844 be an available upgrade for my pool system? The one mentioned above is a 1.5 hp.. would like prefer a 3hp pool motor. Would you also be able to let me know all identifying parts needed for this current setup for the b2844 motor. Thank you
Reply
Hi Carlos, The largest motor you could add to this pump is this 2.5 HP Flo Pro Replacement Motor and you would need to replace your impeller with this 2.5 HP Flo Pro Impeller Kit and you will still need this Jandy Flo Pro Shaft Seal
Reply
Will this pump replace this one?
Hello, the correct replacement motor for the motor included in your photo is the 5112-271. You will also need a Hayward Tristar seal kit (if this motor is the original that came with the complete pump) when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Does the pump come with a seal kit or does it need one?
Reply
Hi Randy, seal kits are separate. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
how many gallon an hour does it pump
Reply
Hello, so there are a few variables to consider when calculating a pump's gallons per minute. Here is a guide that we put together called "How To Read a Pool Pump Curve" that should help with that.
Reply
Is this the proper pump to replace my pump in the photo? Would there be any gain in moving to a higher HP pump? Thank you!
Hi Paul, the correct replacement motor for the motor included in your photo is the 5112-271. You will also need a Hayward Tristar seal kit when you replace your motor assuming you do indeed have the Tristar complete pool pump. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I have a 2 speed Jandy Stealth Pool Pump SHPM2.0-2 Serial J06FK1905 HP 2.0, Century Motor (A O Amith) 7-193990-07 Type CXPM Frame Y56Y RPM 3450/1725 Volts 230 Amps 10.0/3.5 HP & SF unknown. I am not sure if I need a Century B2984 or B2983 based upon previous comments? I would like the Amps to be 3.5 at low speed. Do I also need a 2 speed switch and gasket seal with this purchase? Thank you in advance for your help!
Hi Tim, yes, this is the correct replacement motor for the motor included in your photo and the hi/lo switch is listed in the motor details. You will also need a Jandy Stealth SHPM shaft seal when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
My pump failed. Just need to know if this will replace it and any other stuff I will need such as seals, etc. Please see pic. Thank you!
Hello Brian. Yes, the Century B2983 will replace your existing motor. At a minimum, the shaft seal should be replaced along with any rubber seals or o-rings that are a part of the wet end assembly: Such as the seal plate gasket/o-ring, and diffuser o-ring. The shaft seal and gaskets/ o-rings are specific to the Pump Manufacturer and Pump Model. If you could provide additional information or pictures of the pump itself inclusive of any labeling that may be on the pump housing and wide angles of the pump, we could determine the appropriate shaft seal and o-ring kit for this project. Century 1.5 HP Square Flange 56Y Dual Speed Full Rate Motor - B2983
Reply
I need help with a replacement motor. Please see the pictures
Hello Sam. The Century Motors 1.65 THP Dual Speed Full Rate Motor model SQS1102R is a compatible replacement for the MaxFlo XL model SP2310X152 pool pump. The SQS1102R is a 1 HP Full Rate Motor with a 1.65 SF (Service Factor) for a total horsepower (THP) of 1.65, matching your existing motor THP rating. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced at the same time. Pump Shaft Seal 5/8" - - SPX2700SA PSR-200 Valve To Filter O-ring Id 6-3/4", Od 7-1/8" (gmx600f) O-263 Bulkhead O-ring - SX220Z2 Century 1.0 HP Square Flange 48Y Dual Speed Full Rate Motor - SQS1102R
Reply
I am sure this motor is the right replacement for my Hayward pump. But all the labels on the pump are too faded to read. But the motor label is identical. All that is on the pump is "Hayward". I am attaching photos with the hope you may be able to recommend a seal and O-ring/gasket kit. And lastly, do you have a recommended full pump & motor replacement (1.5HP 2-speed) that will fit with existing collars?\ where I can just unwire the old one, unscrew the old pump, and slap in a new one? Thanks.
Yes, the B2983 motor is identical to the one you need to replace on your Hayward TriStar SP3200X Series Pump. Here is the Tune Up Kit Hayward - GOKIT81 for you, which contains all of the o-rings and the new motor shaft seal as well. Hayward does still make (and we do carry) the TriStar pumps, though we can't guarantee that it would be a simple drop-in replacement for you; you may need to rework some plumbing.
Reply
What an awesome response! Thank you. As you can see from the photos, the suction side of the pump is slammed-plumbed. It will take some work to remove some fittings. Can you send me a link to your recommended tristar pump and the price please? Wow, you people are great!
Reply
We only have the single-speed Hayward TriStar 2 HP, Max Rated Pump - W3SP3215X20, or the Hayward TriStar VS Pump 2.7 HP - W3SP3206VSP the VS is California Title 20 Compliant, the single-speed is not. Simply click each part number to navigate to the product pages. California’s New Variable Speed Pool Pump Law
Reply
Will this dual speed motor replace a single speed motor on a Jandy FHPM1.5 pump? What parts would I need to convert this pump to dual speed? ( I sent the same question for the single speed motor by mistake)
Reply
Hello Paul. The Century Motors 1.5 HP Dual Speed Full Rate Motor model B2983 is compatible with the Jandy FloPro FHPM Series Pump (2008-Present). It is recommended that the motor shaft seal and backplate o-ring be replaced concurrent with the new motor. Pump Seal, Extra Heavy Duty PS4280 (Saltwater Pools) - PS-4280 Backplate O-ring To convert to the dual speed motor it will be necessary to install a second timer such as the Intermatic Dual Speed Timer model T106R. Pool Timer Dual Speed Pump Timer - T106R For manual operation the Two-Speed Toggle Switch Assy can be utilized. Two-Speed Toggle Switch - Lo/Off/Hi
Reply
Hello. I have a century centurian mod # 193989xcn… type cxpm, frame Y 56 Y
The high speed motor won’t start and I’ve replaced the run capacitor with no affect. Do you sell a replacement 2 speed pump.
Hi John, it sounds like the problem is a shorted phase winding since your capacitor is good. This Century 1.0 HP Dual Speed Motor - B2982 will be a perfect replacement. Let us know if you need help choosing a new motor shaft seal or tune-up kit to ensure a leak-free installation.The B2983 motor has too much horsepower t be a perfect replacement - see this article on Is a 1.0HP Motor the Same as a 1.5HP Motor? for an explanation on listed motor horsepower.
Reply
I have a AO smith Part # 7-K56AA23A04-05, 1.5hp, Y56Y frame, 208/230, SF 1.23, 3450/1725 RPM, 8.5/1.5 amps.
with a with a tag on it that states "this pump must be installed with a two-multi or variable speed pump motor controller, time clock...etc.
do you have something I can use?
Hello Cecil. The Intermatic Dual Speed Pump Timer model T106R is designed to work in conjunction with the existing pump timer. The existing timer controls ON/OFF. the T106R controls the HIGH/LOW speed function. Pool Timer Dual Speed Pump Timer - T106R
Reply
I need to replace my motor. Is this the correct motor? Also, what seals do I need to replace?
Hello, the Hayward 1-1/2 HP Maxrate Dual Speed Tristar Motor, 208-230v- SPX3210Z2MER would be the exact replacement motor, but you could also use the Century 1.5 HP Square Flange 56Y Dual Speed Full Rate Motor - B2983 if that is your preference. The seal kit for your pump will be the Saltwater Tune Up Kit Hayward TriStar/EcoStar - GOKIT81SALT, and the toggle switch for both motor options will be Toggle Switch and Canopy Kit for 56Y 2-Speed - 2512558-001.
Reply
We ordered the B983 mortar to replace ours but did not get a gasket kit to go with it. Can you tell me the correct part number to order?
Hello, the gasket kit will be associated with your pump housing, not the motor; if you are able to provide me the model of your pump housing, I would be able to provide you a recommendation for the correct gasket kit.
Reply
We can’t find any other wording or labels, hopefully these pictures will give enough clarity to help figure out which gasket kit will be needed.
Thank you. The pump is the Hayward TriStar SP3200X Series. The Hayward TriStar, EcoStar Pool Pump Seal Kit - Model GOKIT81 or Saltwater Tune Up Kit Hayward TriStar/EcoStar - GOKIT81SALT for salt pools is recommended.
Reply
We need a gasket set, can you help me with the correct one to purchase?
Hello, the gasket set for your specific pump housing would be the Saltwater Tune Up Kit Hayward TriStar/EcoStar - GOKIT81SALT.
Reply
Will this motor work to replace the current one on a Hayward Tristar 1.5hp 2 speed pump? The current one is a century Sp3215z2be also what shaft seal kit is needed
Reply
Hi Danny, the B2983 motor would be a perfect replacement for your old one. Don't forget to add a Tristar tune-up kit for a leak-free installation. Visit our article on Are All Motors Created Equal? to see why the 1.5HP replacement is the same as the 2HP original motor.
Reply
