?     Asked on 2/13/2012by Guest

I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
 Reply

A  Answered on 2/13/2012 by InyoPools Product Specialist Patrick P.

You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
 Reply


?     Asked on 10/15/2014by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
 Reply

A  Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
 Reply


?     Asked on 7/8/2015by Inyo Visitor

My sta rite MPRA6E-147L pump started to make a louder noise then usual so I looked at it and found that it is leaking a little bit of water from the bottom of it. Could the leak be the cause of the noise?
 Reply

A  Answered on 7/11/2015 by InyoPools Product Specialist Patrick P.

Yes normally a leak can cause to seal failure which will cause the bearings to go bad in the motor. A sign of the bearings going bad is that the motor starts to run loud.
 Reply


?     Asked on 1/31/2016by Jimbo

Will this go kit work on my Dyna-glas 1HP MPFA6E-146L pump? Its a very old model.
 Reply

A  Answered on 2/2/2016 by InyoPools Product Specialist Lennox H.

Hi Jimbo, The Sta-Rite Dyn Glas & Dyna Max Tune Up Kit will work with your Dyna-glas 1HP MPFA6E-146L pump
 Reply


?     Asked on 2/13/2016by Evan

I have a Sta Rite Super Max 1.5HP, 1.1SF. I found my replacement pump on your site, but which service kit or parts do I need to go with it?
 Reply

A  Answered on 2/16/2016 by InyoPools Product Specialist Andy O.

Evan, They do not have a tune-up kit for the supermax, but the most important seal would be the shaft seal, which is part# 5250-210 Pump Seal 200, Heavy Duty PS3867. All other o-rings would have to be purchased separately.
 Reply


?     Asked on 3/28/2016by Inyo Visitor

I have a Sta-rite Dyna-Glas pool pump, model # MPRA6F-148L. It has a small leak from the seal area. Will the O-ring from this kit fit my pump?
 Reply

A  Answered on 3/28/2016 by InyoPools Product Specialist Andy O.

Hello- The GOKIT47 Tune Up Kit Sta Rite Dyn Glas & Dyna Max is the correct kit for your pump, the o-ring in the kit will work with your pump.
 Reply


?     Asked on 6/25/2016by jack nemeth

I have small pcs of plastic circles aprox. 1/4" round in my filter? Sta-rite dyna glass PLD36what parts do i need?
 Reply

A  Answered on 6/30/2016 by InyoPools Product Specialist Lennox H.

Hi Jack, I'm not sure exactly which part you're referring to. Click link >Sta Rite System 2 MOD Media & MOD D.E. PLM & PLD for the available PLD parts and Sta-Rite Dyna-Glas and Dyna-Max for available Dyna-Glas parts.
 Reply


?     Asked on 7/22/2016by Omer Malik

I am looking for the rebuilt kit for MPRA6G-155L. Will this kit fit. On a somewhat related note, I am looking for a capacitor for the motor as well. The motor is : A100GLL.
 Reply

A  Answered on 7/24/2016 by InyoPools Product Specialist Lennox H.

Hi Omer, Yes, this kit can be used with the MPRA6G-155L pump. The A100GLL motor has a 20 MFD 370 Volt Run Capacitor (RD-20-370) and a 36-43 MFD 220-250 Volt Start Capacitor (BC36M-250-S).
 Reply


?     Asked on 8/5/2016by Susan

I purchased a USQ1102 replacement motor for a Sta Rite Dyna-Glas pump. Then I ordered the wrong tune up kit. I see now that the correct kit is Gokit47, but it does not appear to have the square gasket included. Which gasket should I order?
 Reply

A  Answered on 8/10/2016 by InyoPools Product Specialist Lennox H.

Hi Susan, The Sta-Rite Dyna Glas/Max pump does not have any square gaskets. It's possible that over time which happens the o-ring becomes flat causing it to appear square.
 Reply


?     Asked on 5/21/2018by Ernesto

My pump Sta-Rite # is MPFA6F 147L what is the Kit # for it Tthanks Ernie
 Reply

A  Answered on 5/21/2018 by InyoPools Product Specialist Lennox H.

Hi, Ernesto. This GOKIT47 is the correct tune up kit for your model pump. 
 Reply


?     Asked on 5/22/2018by Frank

What is the proper “Go Kit” for my pump,PHK2RA6E-102L.
 Reply

A  Answered on 5/22/2018 by InyoPools Product Specialist Hector F.

We, unfortunately, do not carry a gokit for this series pump so you would need to get each seal or gasket individually. If you click here, keys  14, 16, and 22 are the most commonly replaced seals on this model. 
 Reply


?     Asked on 8/3/2018by Cleat

I have a Sta Rite P2RA5E-124L pump on a USQ1102 AO Smith 1 hp motor. What seal kit do I need when replacing the motor?
 Reply

A  Answered on 8/3/2018 by InyoPools Product Specialist Hector F.

I would recommend using the GOKIT54 and if you have the copper cone insert in the seal plate then just remove it. 
 Reply


?     Asked on 3/28/2019by Tommy

I have a Sta Rite pump model MPEA6D-146L. What tune up kit do I need?
 Reply

A  Answered on 3/28/2019 by InyoPools Product Specialist Lennox H.

Hi, Tommy. This Sta-Rite Dyna-Glas & Dyna-Max Tune Up Kit - GOKIT47 is the correct kit for your model.
 Reply


?     Asked on 4/5/2019by Riza

Will this work with Dyna-Pro MPRA6E-205L? Thanks
 Reply

A  Answered on 4/5/2019 by InyoPools Product Specialist Steve M.

Riza, GOKIT47 is the correct seal kit and will work with your MPRA6E-205L. 
 Reply


?     Asked on 4/24/2019by Larry

Will the Gokit-47 work on the MPEAA6YG-168L Dyna-Max starite pump.

 Reply

A  Answered on 4/24/2019 by InyoPools Product Specialist Michelle B.

Yes, that will be the correct gokit.
 Reply


?     Asked on 6/18/2019by Tom

Our pump housing is leaking and the identifocation numbers look old and warped but we wrre able to make out these numbers on the housing: mpra6e-147l We would like to know if this is the correct seal kit for teplacement and what style pump it is..it days starite but we do not see dybaglass or dynapro
 Reply

A  Answered on 10/9/2019 by InyoPools Product Specialist Hector F.

Yes, this is the correct seal kit for your model pump and is referred to as the Sta-Rite Dyna-Glas/Dyna-Max. 
 Reply


?     Asked on 7/19/2019by Robert A Johnson

Ordered a USQ1102 motor. What gasket and O-RING kit would I need for the install. Thanks, Bob Johnson
 Reply

A  Answered on 7/19/2019 by InyoPools Product Specialist Lennox H.

Hi, Robert. The tune up kit is specific to the pump housing, not the motor. If you do not know or have your pump housing model, check out our Replacing Parts For A Pump You Don’t Have A Model Number For Blog.
 Reply


?     Asked on 7/23/2019by Inyo Visitor

I have a Sta-Rite Dyna-Glas MPRA6F-148-L pump what motor and seal kit do you recommend thank you.
 Reply

A  Answered on 7/23/2019 by InyoPools Product Specialist Hector F.

This would be the correct seal kit and the replacement motor is the model USQ1152
 Reply


?     Asked on 8/2/2019by luciano

Hello, I have a Sta Rite MPRA6G - 155L Im looking for a replace motor in A O Smith. Do you have it?
 Reply

A  Answered on 8/2/2019 by InyoPools Product Specialist Lennox H.

Hi, Luciano. The USQ1202 is the replacement motor based on your pump model. You will also need this Tune Up Kit - GOKIT47
 Reply


?     Asked on 8/7/2019by Chris

Will this fit a sta rite MPFA6F-147L ?
 Reply

A  Answered on 8/7/2019 by InyoPools Product Specialist Lennox H.

Hi, Chris. Yes, this is the correct tune up kit for your model Sta-Rite MPFA6F-147L pump. 
 Reply


?     Asked on 6/2/2020by Douglas Bartzatt

Will this fit a MPRA6D-146L?
 Reply

A  Answered on 6/10/2020 by InyoPools Product Specialist Hector F.

Yes, this tune-up kit will work with the series model MPRA pool pumps. 
 Reply


?     Asked on 6/12/2020by Inyo Visitor

is this model # correct for this purchase? model # MPRAE 14TL
 Reply

A  Answered on 6/12/2020 by InyoPools Product Specialist Hector F.

Yes, this GOKIT is compatible with the Sta-Rite MPRA series pool pump. 
 Reply


?     Asked on 7/3/2020by chris kerrigan

Will this work on Mpra6e 147l
 Reply

A  Answered on 11/20/2020 by InyoPools Product Specialist Hector F.

Hi Chris, yes this seal kit is compatible with the Sta-Rite MPRA series pool pump. 
 Reply


?     Asked on 7/31/2020by Jerry Sokolowski

Hi, Is this kit compatible with sta=rite MPRA6F-148L,1:5 HP and do you ship to Canada? thanks
 Reply

A  Answered on 10/26/2020 by InyoPools Product Specialist Megan C.

Hi Jerry, yes this seal kit is correct for the model Sta-Rite MPRA6F-148L pool pump.
 Reply

  • Commented on 10/26/2020 by Product Owner

    do you ship to Canada thanks Jerry
     Reply


?     Asked on 1/30/2021by Don Crawford

Will the GO KIT fit a STA-RITE Pump # MPRA6D-146L. Thankyou.

 Reply

A  Answered on 2/4/2021 by InyoPools Product Specialist Hector F.

Hi Don, yes this seal kit is compatible with the Sta-Rite Dyna-Glas/ Dyna-Max pool pump series. 
 Reply


?     Asked on 5/17/2021by Chris Morton

Does this kit include the large O-ring that sits beneath the clear, removable Plexigas cover?
 Reply

A  Answered on 5/17/2021 by InyoPools Product Specialist Danny R.

I believe you are referring to the lid o-ring.  The lid o-ring is included in this kit.
 Reply


?     Asked on 8/7/2021by Barry McCarty

Is this kit for Model MFRA6E-147L
 Reply

A  Answered on 1/26/2022 by InyoPools Product Specialist Joe S.

Good day, yes this kit works on the following units. DYNA-GLAS/DYNA-MAX POOL PUMP 3/4 THROUGH 2 HP MODELSMPRA, MPEA 3/4 HPMPRA, MPEA 1 HPMPRA, MPEA 1.5 HPMPRA, MPEA 2
 Reply


?     Asked on 9/23/2021by Steven Race

Needing kit for my pump MPFA6F
 Reply

A  Answered on 9/23/2021 by InyoPools Product Specialist Rich N.

Hi Steven.  Yes, this is the correct tune up kit for your model Sta-Rite MPFA6F pump. 
 Reply


?     Asked on 11/30/2021by jerry LaFemina

I have a Sta-Rite Dyna-max MPFA6E146L. What tune up kit will I need and should I replace the impeller ? System is working well but did see a couple water drips between motor and pump housing

 Reply

A  Answered on 11/30/2021 by InyoPools Product Specialist Stephen B.

Thank you for contacting Inyo Pools, The correct tune up kit is Gokit47. I sent you a quote to your e-mail for the correct part.
 Reply


?     Asked on 12/8/2021by jose a abrahantes

hi my pump its the MPRA6G-155L this kit its the right one thanks
 Reply

A  Answered on 12/8/2021 by InyoPools Product Specialist Rich N.

Hi Jose, the Tune Up Kit Sta-Rite Dyna-Glas & Dyna-Max - GOKIT47 will be perfect for your MPRA6G-155L pump.
 Reply


?     Asked on 8/30/2023by Rob

I need to know the part numbers especially for seal, is it a 201?
 Reply

A  Answered on 8/30/2023 by InyoPools Product Specialist Jacob F.

Hello, the shaft seal used in this seal kit is Standard Pump Shaft Seal 3/4" - PS-201, which is a 201 seal.
 Reply