?     Asked on 4/22/2015by brent

How many watts is this bulb?
 Reply

A  Answered on 4/22/2015 by InyoPools Product Specialist Lennox H.

Brent, This bulb is 150 watts
 Reply


?     Asked on 6/1/2015by Inyo Visitor

the colors are not showing up as clearly as they were when new. the light w/color wheel was installed in 1999. Do I need a new bulb or a new color wheel or both?
 Reply

A  Answered on 6/2/2015 by InyoPools Product Specialist Patrick P.

I would first start off of with a new lamp assembly, if you did not see an imrovement after that replacement then the next thing I would try is the color wheel.
 Reply


?     Asked on 6/9/2015by MIKE

Hi, I have a fiberstars 6004 on my pool, I need a replacement bulb, do you sell them or know a reputable place I could order one from? thank you.
 Reply

A  Answered on 6/9/2015 by InyoPools Product Specialist Patrick P.

Hi Mike, the bulb by itself cannot be changed on the Fiberstars 6004 illuminator. You would require the bulb assembly on this page which we have in stock and could ship out right away.
 Reply


?     Asked on 7/6/2015by Rick

My 6008 pool light powers on but the bulb on the inside of the unit doesn't light nor does the light in the pool.
 Reply

A  Answered on 7/14/2015 by InyoPools Product Specialist Lennox H.

Hi Rick, You will have to contact S.R. Smith at 1.800.824.4387 to troubleshoot where the issue is, whether the bulb needs to be replace or another issue could be causing the issue.
 Reply


?     Asked on 7/19/2015by Inyo Visitor

Lamp assembly flickers but will not come on
 Reply

A  Answered on 7/21/2015 by InyoPools Product Specialist Joe S.

Lamp "Restrike" When turning the system off and then turning it immediately back on, it may take 1 to 3 minutes before the lamp comes back on. This process allows the lamp to cool down and then restart. This is a normal function of the Metal-Halide lamp system that the Fiberstars 6004 / 6004-AS illuminator uses.-THE UNIT SHUTS OFF AFTER A FEW MINUTES THEN COMES BACK ON Check to see if the air vents are blocked. Refer to the above drawing to make sure the vents are clear Turn off the power and remove the two screws securing the cover and check for an obstruction in the cooling fan
 Reply


?     Asked on 7/26/2015by Floyd

how do I know if the bulb is bad? is there a burnt piece inside? what would I trouble shoot, if I change the fuse, and it still does not come on?
 Reply

A  Answered on 7/28/2015 by InyoPools Product Specialist Lennox H.

Hi Floyd, There is a few troubleshooting steps you can do that is in the Fiberstar Owner's Manual. If you're still having problems you can contact Fiberstar at (800)327-7877.
 Reply


?     Asked on 8/3/2015by Luke Sheridan

I have a Fiberstars fiber optic pool light model 6008. Is this the correct lamp assembly unit for Model 6008. Thanks for your help.
 Reply

A  Answered on 8/3/2015 by InyoPools Product Specialist Patrick P.

Hi Luke, Yes the Y206000 lamp assembly is the correct lamp for the Fiberstars 6008.
 Reply


?     Asked on 8/21/2015by Inyo Visitor

I've got three model 6000; pool rep says they need to be replaced. It's about 15-yrs old. Is that about the expected life span? Can it be replaced with a model 6004?
 Reply

A  Answered on 8/25/2015 by InyoPools Product Specialist Alex V.

Hello, 15 years sounds about right for the lifespan of the illuminator. The Fiberstars 6004 illuminator (4 color) is the current version of the 6000 illuminator.
 Reply


?     Asked on 12/2/2015by patric

I just need the light bulb only...is their a part no. for the bulb only...
 Reply

A  Answered on 12/2/2015 by InyoPools Product Specialist Lennox H.

Hi Patric, The bulb is only includes in the Lamp Assembly (Y206000).
 Reply


?     Asked on 12/21/2015by Luis

Anyone has the electrical diagram of the Fiberstar 6004 model? No fan noise, no light. Fuse checked good. Any help will be appreciated. Thanks
 Reply

A  Answered on 12/22/2015 by InyoPools Product Specialist Charlie R.

Luis,We have the 6004 installation manual on our site. If that doesn't help, you might want to give Fiberstars a call to troubleshoot the unit with them.
 Reply


?     Asked on 3/23/2016by Ron

Will this fit a 6004FS? What is the difference between a 6004 AS and 6004FS unit?
 Reply

A  Answered on 3/24/2016 by InyoPools Product Specialist Lennox H.

Hi Ron, According to SR Smith the 6004"FS" is an indicator for FiberStar which has been acquired SR Smith. The 6004FS is same as the 6004, the 6004AS is the auto-synch model which you can synch more than one unit together.
 Reply


?     Asked on 5/4/2016by Inyo Visitor

I have the 6008 model but my lights are real dim what should I do?
 Reply

A  Answered on 5/6/2016 by InyoPools Product Specialist Lennox H.

Hi, Re-porting the  fibers can resolve the dimming of the light. Instructions can be found on page 4 of the 6004 Installation Manual.
 Reply


?     Asked on 7/10/2016by dan p

no fiber light around pool at all. Fan works, light works. Trying to get more fiber up so I can cut it off & have new fiber ends. Sounds like I have to loosen big conduit nut to free fibers. When I try to loosen nut the whole port assembly turns with it. I can't push it up thru 4ft. of 3/4" conduit. Tried install instructions on pg 4 but that does tell how to replace burnt fiber ends. Thanks, Dan
 Reply

A  Answered on 7/14/2016 by InyoPools Product Specialist Lennox H.

Hi Dan, You can not replace the burned fibers you will have to cut them off using a hot knife
 Reply


?     Asked on 7/12/2016by mary

I have a fiberstrs 6000 not as brite as should be what could this be?
 Reply

A  Answered on 7/16/2016 by InyoPools Product Specialist Lennox H.

Hi Mary, You may need to report the fibers, instructions can be found in the Fiberstars 6004 Installation Manual.
 Reply


?     Asked on 8/20/2016by Matt

What is the resistance for the 6004 bulb. I want to check if the bulb is bad
 Reply

A  Answered on 8/31/2016 by InyoPools Product Specialist Lennox H.

Hi Matt, The resistance of the bulb is 96 ohms.
 Reply


?     Asked on 9/23/2016by Robin Aulenbach

I need a Bulb # Y20-6000.....Need it quickly, and I live in London Ontario Canada....do you know a dealer here that may have parts
 Reply

A  Answered on 10/4/2016 by InyoPools Product Specialist Scott W.

I am not aware of a dealer in your area. I would recommend calling Next Step Products at 407-857-9900 to see if they know of any of their vendors in your area.
 Reply


?     Asked on 1/16/2017by Inyo Visitor

hAVE A fIBERSTAR RM 6000 NEED A TECH OR, A CHEAP REPLACEMENT FOR IT! bOUGHT THE HoUSE LAST MONTH, IN northern fLORida, just want to fix ix it. Suggestions . tks
 Reply

A  Answered on 1/17/2017 by InyoPools Product Specialist Scott W.

Yes, the replacement for that is made by S.R. Smith and is part number 3TR-PT-6000.
 Reply


?     Asked on 2/28/2017by Scott

I bought the y20-6000 bulb but its too long for my enclosure. i have a series 6000 fiber star. are there shorter vesions of them. i see in the pictures that the bulb looks about an inch smaller than mine
 Reply

A  Answered on 3/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Scott. The manufacturer recommends purchasing the entire lamp assembly to prevent this issue. We do not carry just the replacement bulb.
 Reply


?     Asked on 4/2/2017by Robert

We have the Fiberstar 6004 model pool light. The light quit working and I have no idea why. Any suggestions would be appreciated. Thanks,
 Reply

A  Answered on 4/4/2017 by InyoPools Product Specialist Lennox H.

Hi, Robert. It could be a few things, I would recommend following the troubleshoot options in the Fiberstar 6004 Owner's Manual.
 Reply


?     Asked on 4/23/2017by David brown

What should the voltage and wattage be coming from the light assembly to the bulb for a fiberstar 6004?
 Reply

A  Answered on 4/27/2017 by InyoPools Product Specialist Stacey M.

Hello David, This unit requires 120 volt 60 hz only.
 Reply


?     Asked on 5/13/2017by Rob

I have a 6004 illuminator with the y20-6000 light assembly. Tried multiple new assemblies and bulbs, still no light. Meter testing, i am getting 268 V AC at the light socket. Believe this should be 120V and I'm frying bulbs as a result when plug in new. Any feedback you can provide as to why i'm getting 268V AC? Is it necessary to replace the entire 6004 unit, possibly due to a bad transformer?
 Reply

A  Answered on 5/14/2017 by InyoPools Product Specialist Lennox H.

Hi, Rob. The 6004 unit requires 120 VAC, if you're getting 268 VAC then you will need to double check the input voltage.
 Reply


?     Asked on 12/13/2017by LARRY HARRIS

Can I buy bigger light AND color wheel for my 6004??
 Reply

A  Answered on 12/13/2017 by InyoPools Product Specialist Lennox H.

Hi, Larry. Unfortunately, you cannot. 
 Reply


?     Asked on 12/13/2017by LARRY HARRIS

are the 6004 and 6600-as the same if not whats the differance thanks
 Reply

A  Answered on 12/15/2017 by InyoPools Product Specialist Lennox H.

Hi Larry. The 6004 and the 6600 unit are the same units. The 6600 & 6600AS were as sold as a two piece kit which included the 6004 and the CCS-600 port kit. The CCS-600 port kit allowed the 6004 unit to port up to 600 strands of fiber. The "AS" model is the Auto Sync unit which is used when you're using multiple units. 
 Reply


?     Asked on 5/29/2018by Pam

Hi, My manual says Lifetime Illuminator 6000 series. Not sure exact model number. Bought about 2003. Light not coming on. 1 fuse missing from our unit - wanted to buy both new to see if that works. Is one a 7 amp and 1 a 1 amp fuse? How do I know which to put where? And if that doesn't work, would I try a new lamp next? Thanks
 Reply

A  Answered on 5/29/2018 by InyoPools Product Specialist Lennox H.

Hi, Pam. There should be a wiring diagram on the unit identify where everything goes. Try to locate that diagram or use this 6000 Series Wiring Diagram to determine which fuse is needed. 
 Reply


?     Asked on 9/6/2018by Joe

Do you sell the bulb separately for the Fiberstars Y-20-6000 assembly?
 Reply

A  Answered on 9/7/2018 by InyoPools Product Specialist Lennox H.

Hi, Joe. We do not sell the bulb only for this Lamp Assembly.
 Reply


?     Asked on 5/21/2019by daniel ferguson

My light doesn't seem as bright as iy was before what can I do to check why? clean it? change the light bulb?
 Reply

A  Answered on 5/23/2019 by InyoPools Product Specialist Megan C.

Hello, Unfortunately, we would not know. We recommend contacting Fiberstars. You can reach them at 1-800-824-4387.
 Reply


A  Answered on 8/5/2020 by Product Owner

Several thoughts come to mind. - Bulb could be failing. - The fiber bundle may need a fresh cut - There are several glass filters between the light source and the fiber bundle including the color wheel. Remove, clean, replace.
 Reply


?     Asked on 6/3/2019by Greg

What's the wattage of the bulb? 150 w or 250W
 Reply

A  Answered on 6/8/2019 by InyoPools Product Specialist Hector F.

This bulb is 150 watts.
 Reply