?     Asked on 10/7/2014by Guest

Does this work with older rs2/6
 Reply

A  Answered on 10/7/2014 by InyoPools Product Specialist Patrick P.

You would need the Aqua Palm Kit which includes the remote and receiver and you would also need to make sure your software revision is M or higher, you should be able to go into your controller and verify your software revision.
 Reply


?     Asked on 11/17/2014by Leslie

Dog ate the outside cover of the Jandy PDA. The circuit board looks ok just need new outer case and connector for board to case. Is this possible to buy and if so cost?
 Reply

A  Answered on 11/17/2014 by InyoPools Product Specialist Robert M.

Hello Leslie - The case is not available. The only option is to replace the complete handheld control. The Jandy part number is R0444300.
 Reply


?     Asked on 4/22/2015by Greg doan

Is this a PDA PS6?
 Reply

A  Answered on 4/23/2015 by InyoPools Product Specialist Robert M.

Hello Greg - The R0444300 will work with any of the PDA models.
 Reply


?     Asked on 6/7/2015by Vince

I have a counter top remote (model 8156) for my Jandy Aqua link RS 6613 Firmware is L Can I use your Aqua Palm together or instead of my current remote ? How do I get and install a 52 pin PCB ?
 Reply

A  Answered on 6/7/2015 by InyoPools Product Specialist Patrick P.

Hi Vince, unfortunately the Aqua Palm is compatible on Aqualink systems of Firmware M or later. You could go with the Aqualink PDA Conversion Kit which includes a new pcb board (latest firmware) along with the wireless handheld remote. The wireless handheld remote would take the place of your current remote.
 Reply


?     Asked on 5/28/2016by New Pool Owner

I have the AquaLink RS PDA. I really like how easy it is to turn on and off pool equipment. Not sure what happened, but all of the sudden it stopped working. I did try to put in new batteries and nothing. I moved the batteries around and it did turn on but then it started going "going crazy." What do I do?
 Reply

A  Answered on 5/30/2016 by InyoPools Product Specialist Lennox H.

Hi, It sounds like the remote is bad and will need to be replaced. There aren't replacement parts available to repair the remote
 Reply


?     Asked on 5/28/2016by Inyo Visitor

I have a Jandy PDA Wireless Hand Held Remote Model #8265. Will this remote work as a replacement?
 Reply

A  Answered on 5/30/2016 by InyoPools Product Specialist Lennox H.

Hi, This remote will replace your Jandy PDA.
 Reply


?     Asked on 6/11/2016by LEN ANDERSON

how do I know if I have REV "M" software?
 Reply

A  Answered on 6/18/2016 by InyoPools Product Specialist Lennox H.

Hi Len, You will have to look on the chip  on the PCB that is located in the main controller.
 Reply


?     Asked on 10/12/2016by dave spencer

i have a model 8265 and it just flat out died; it's 10 years old. If I order a new 8265 is there anything else to do buy or can I just buy it , pull it out of the box, add batteries and then synch it to the panel? and if so, how do I synch it?
 Reply

A  Answered on 10/13/2016 by InyoPools Product Specialist Alan M.

According to the research I have done, the Jandy Aqua Palm is ready to go out of the box after batteries are installed. There is no special syncing necessary. The AquaLink RS Systems must have Rev "M" software or later. You can verify this by looking at the chip on the PCB that is located in the main controller.
 Reply


?     Asked on 5/18/2020by Erin Green

No lie, my dog ate mey remote... lol.. it says this model is no longer available, what do I do?? Thank you, Erin
 Reply

A  Answered on 12/31/2020 by InyoPools Product Specialist Hector F.

Hi Erin, these remotes are still available however just not able to be sold with online pool retailers. 
 Reply