Details

Top

Model # R0444300

Alternate Part #'s 299107, JDY-30-0001, JDYR0444300

Product Description

Handheld Unit Only

The Jandy AquaPalm brings the power and flexibility of a wireless remote to new or existing AquaLink RS control systems with Rev "M" software or later. Designed to be the "must have" add-on, the AquaPalm allows remote control of your equipment in an attractive, waterproof and portable handheld.

Features

  • Ultra compact, wireless, waterproof, handheld remote - it even floats!
  • Leading edge wireless technology offers a robust, reliable communication network for a flexible and simple installation
  • 500 ft. range of operation - does not require line of sight
  • Lower installation costs than a hard wired system
  • No wiring between the equipment and the control panel - that means no trench, conduit, or indoor wiring
  • Simplified Windows® style drop-down menus for control of filter pump, spa switch-over, heater, solar and up to 7 auxiliary circuits with the push of just one button
  • Personalized programming/labeling of all equipment and service information
  • AquaPure interface for control of on-site chlorine production
  • JandyColors pool and spa colored light interface for convenient color changing
  • Large backlit display of signal strength, battery charge, day, time, water temperatures plus complete equipment status
  • Powered by two AA batteries - average life, one pool season

*To upgrade to the PDA/Aqua Palm Hand Held w/18 Channel RF, R Kit - R0687300, AquaLink RS Systems must have Rev "M" software or later. If older, a new 52 pin PCB must be purchased.



Top

?     Asked on 10/7/2014by Guest

Does this work with older rs2/6
 Reply

A  Answered on 10/7/2014 by InyoPools Product Specialist Patrick P.

You would need the Aqua Palm Kit which includes the remote and receiver and you would also need to make sure your software revision is M or higher, you should be able to go into your controller and verify your software revision.
 Reply


?     Asked on 11/17/2014by Leslie

Dog ate the outside cover of the Jandy PDA. The circuit board looks ok just need new outer case and connector for board to case. Is this possible to buy and if so cost?
 Reply

A  Answered on 11/17/2014 by InyoPools Product Specialist Robert M.

Hello Leslie - The case is not available. The only option is to replace the complete handheld control. The Jandy part number is R0444300.
 Reply


?     Asked on 4/22/2015by Greg doan

Is this a PDA PS6?
 Reply

A  Answered on 4/23/2015 by InyoPools Product Specialist Robert M.

Hello Greg - The R0444300 will work with any of the PDA models.
 Reply


?     Asked on 6/7/2015by Vince

I have a counter top remote (model 8156) for my Jandy Aqua link RS 6613 Firmware is L Can I use your Aqua Palm together or instead of my current remote ? How do I get and install a 52 pin PCB ?
 Reply

A  Answered on 6/7/2015 by InyoPools Product Specialist Patrick P.

Hi Vince, unfortunately the Aqua Palm is compatible on Aqualink systems of Firmware M or later. You could go with the Aqualink PDA Conversion Kit which includes a new pcb board (latest firmware) along with the wireless handheld remote. The wireless handheld remote would take the place of your current remote.
 Reply


?     Asked on 5/28/2016by New Pool Owner

I have the AquaLink RS PDA. I really like how easy it is to turn on and off pool equipment. Not sure what happened, but all of the sudden it stopped working. I did try to put in new batteries and nothing. I moved the batteries around and it did turn on but then it started going "going crazy." What do I do?
 Reply

A  Answered on 5/30/2016 by InyoPools Product Specialist Lennox H.

Hi, It sounds like the remote is bad and will need to be replaced. There aren't replacement parts available to repair the remote
 Reply