the band clamp is leaking when i start pump. is there one way band clamp fits on pump or is there a specific way to put on.
Reply
Roland- If you band clamp is leaking make sure you have the knob at the 12 O'clock position on the pump. If you already have it like that, I would check the housing gasket or the pump seal (depending on where it is leaking from). The housing gasket is a part # 5002-14, the shaft seal is part # 354545S, or you could get them both in a kit which is part # GOKIT5.
Reply
Will this fit model number MA-100?
Reply
The correct band assembly, Band Assembly, Complete (313196), is no longer available. Unfortunately, we do not have dimensional information or an alternative part listing for the obsolete band to compare to the one you submitted a question on. Feel free to contact the manufacturer @ 1-800-831-7133 if you need additional assistance.
Reply
I have a pentair pump i need the clamp for the lower/smaller filter. I know the clear lid to the filter is part # P08080 i hope this will help. The part no on the clamp is QL17d9 but can not find this part no. Thanks
Reply
Good morning, You are looking for Clamp Assy. (070711).
Reply
Do you have a band clamp for Pentair ccp320?
Reply
Hi. The Clamp Assembly - 190003 is compatible with the Pentair Clean & Clear Plus Cartridge Filter.
Reply
I have a Dura glas pump - mod# P4E6E-151L. It is leaking at the bottom of the plenum. I have replaced the outer seal and tightened the outer clamp - but it still leaks. there are no cracks in the housing. I am thinking that the clamp (20 yrs. old) may not be doing the job. your thoughts and recommendations would be appreciated. Thanks
Reply
Hi Rick, yes if your pump is a P4E6E-151L and is leaking at the clamp and you have already replaced the o-ring then yes I would replace the clamp. The correct clamp you will need is this P4E6E-151L Replacement Clamp as the 5002-07 clamp is not the correct clamp for your pump.
Reply
Hi We have leak in the impeller housing. We need to replace housing alone. We are having a hard time finding the housing for ours. The band number is 35462 9 or 0 we cant read it well, we think 9. Help Please
Hi Allison, Thank you for the photos those are quite helpful. You have the Pac Fab Challenger Pump and you can find your pump housing through our Pac Fab Challenger Parts Page
Reply
I have a clamp for pool filter marked rg ray 10120. Do you have something that would replace this clamp? I'm having a hard time finding it.
Reply
Can you please send a picture of the entire filter? Or do you know the make/model of the filter?
Reply
Is this band a replacement/compatible to replace Band Clamp #354629? I did a search for that part number and your website brought me to this item.
Reply
I have to replace a clamp band of our pool pump and it's a R.G. Ray # 10120
Do you have ?? Se attached the picture ,
Thanks
Hi Marcio, Yes this band clamp is the proper replacement for the R.G. Ray # 10120
Reply
I have s Pac Fab Challenger 1 1/5 Hp pump which needs a new clamp band assembly and o-ring. The housing has part number p/n 35-5459 on a label attached to it. I have also attached a photo of the pump. Can you tell me the part numbers of the Clamp Band Assembly and o-ring seal I need to order?
Hi Peter you will require this 5002-07 Pentair Challenger Band Clamp and this Pentair Challenger Clamp O-Ring
Reply
Will this fit my FNS 48
Reply
No this does not fit the FNS 48 filter. You will require this FNS 48 Clamp instead.
Reply
I need a Pentair pool pump clamp; I'm can't find the identification on the pump (may be a Challenger ) but the closed clamp's inside diameter is approximately 11 inches.
I'm in Hawaii. Could you tell me what the clamp and shipping costs are, and when the clamp would arrive here.
Than you very much
Reply
Hello Hawaii. The Pump Clamp Assembly is specific to the Pump Model. Attached please find several exploded parts diagrams for Pentair Pool Pumps with Clamp Assemblies. A visual comparison of the Pump Lids and Pump Baskets will assist in identifying your Pentair Pump model. Challenger Dura-Glas Dura-Glas II Max-E-Pro Attached please find a copy of the INYO Pools Shipping Policy which describes shipping options and shipping costs. Shipping Policy
Reply
will this band work on a pentair sep 72 tank lid. the 313196 part doesn't seem to exist anymore.
Reply