?     Asked on 4/18/2015by Inyo Visitor

does handle require skrew or pin? I need gasket with a pin to attach handle. wc 33 tank
 Reply

A  Answered on 4/20/2015 by InyoPools Product Specialist Lennox H.

This requires a pin, the gasket comes with p/n 4679-12 and the p/n for the pin is 4685-07.
 Reply


?     Asked on 4/14/2016by Al Loeser

I have an AquaTools valve, Model #WC112-147, WC112-148. Are AquaTools, Pentaire and Stay-Rite all the same? Will this part work for my model?
 Reply

A  Answered on 4/15/2016 by InyoPools Product Specialist Lennox H.

Hi Al, This part will work with your WC112 Series Valve. AquaTool and Sta-Rite have been acquired by Pentair.
 Reply


?     Asked on 10/3/2016by JOHN BURNETT

I turned the rotor while the pump was running. There are no obvious breaks or cracks in any assembly. The only thing I observed was the yellow spider gasket seemed to have deterorated with pieces scattered about. Symptoms were the waste port was running a trickle of water when the valve was on filter. Looking for suggestions.
 Reply

A  Answered on 10/5/2016 by InyoPools Product Specialist Stacey M.

Hello John, If you have a trickle of water running out of your waste line while your pump is running on filter you need to replace that spider gasket piece. Rotor, W/gasket 4679-12 this type goes to a Sta Rite Multiport 1 1/2" WC112 Series.
 Reply


?     Asked on 5/18/2017by Roger Mc Aloney

Will this part fit a Sta-Rite 53185 filter?
 Reply

A  Answered on 5/18/2017 by InyoPools Product Specialist Hector F.

We show this part as being for a Hayward slide valve SP410X. To further cross reference the parts for your filter you can call in to provide the filter model number and or send in images through our support request page. The model number you providsed boes not crossreference in our system not google.
 Reply


?     Asked on 8/1/2017by Brenda

Is this spider gasket what I need when I am replacing the port assy on sta rite t-210wf with port 261186?
 Reply

A  Answered on 8/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Brenda. This Rotor, w/Gasket - 14965-0028 will only work with the WC112 Series valve. If you have the 261186 valve then you can use the MPV 1.5" Tune Up Kit - APCK1067 or the Diverter Gasket - 271104.
 Reply


?     Asked on 7/7/2018by Bala

I have leaking into the waste port from my sand filter WC112-147. I suspect that I will need to replace the spider gasket. I don't see this as a stand alone piece to purchase. Is this available without the rotor? thanks
 Reply

A  Answered on 7/8/2018 by InyoPools Product Specialist Hector F.

Unfortunately, the spider gasket is not sold separately for this valve. 
 Reply


?     Asked on 4/7/2019by Sandra Washington

I have a Sta-Rite T-240BP-1 Hi Rate Sand Filter. When in recirculate mode it pours water out the backwash pipe. Would this be the proper rotor/gasket to use for replacement with my particular brand of filter?
 Reply

A  Answered on 4/7/2019 by InyoPools Product Specialist Lennox H.

Hi, Sandra. Yes, this Rotor w/ Gasket - 14965-0028 will resolve your issue if you have the original WC112-148 valve. 
 Reply


?     Asked on 4/12/2019by Bruce

My STA-RITE 14965-0021 multiport valve has this rotor/gasket combination, so I am asking here. I don't have any water leaking from or through the valve. But recently when the pump turns off, I can hear air leaking INTO the system around this valve. Previously the filter and plumbing were airtight. So when the pump started, there was no air in the system and the pump did not have to prime. Now it needs to prime. Will replacing this rotor/gasket fix the air leak? Or is another part needed?

 Reply

A  Answered on 4/12/2019 by InyoPools Product Specialist Lennox H.

Hi, Bruce. Since the pump is not priming, the issue will be on the suction side of your system. The filter is on the pressure side of your system which will assist your pump in priming by leasing any air trapped in the system.
 Reply


?     Asked on 4/6/2020by Steve

Is this gasket compatible with the Jacuzzi Aquamax 200 filter?
 Reply

A  Answered on 4/6/2020 by InyoPools Product Specialist Patrick P.

Hi Steve, Does your valve say DVK6 or DVK7 on it? Also, does it bolt-on or clamp onto your filter? Would it be possible to submit a close-up photo of the valve as well as a wide shot showing the complete filter? Simply click the reply link below to supply this information and then we will be able to make the proper suggestion. 
 Reply

  • Commented on 4/6/2020 by Product Owner

    Here are some pics. Can you provide part number for whole assembly? Thanks

     Reply

    • Commented on 4/6/2020 by InyoPools Product Specialist Patrick P.

      Thanks for the photos Steve! One last question does your valve bolt on to the filter or clamp onto the filter?
       Reply


?     Asked on 4/26/2020by Tawnya

I am looking for a spider gasket/flo valve gasket/ or seal diverter gasket for a Sta-Rite 14965-0021. Can you assist?
 Reply

A  Answered on 4/28/2020 by Industry Professional

Yes you are able to use this 14965-0028 (27-102-1322) Rotor with gasket on that multiport valve
 Reply


?     Asked on 5/22/2020by Realist_one

My Sta-Rite Waterford H. R. Sand filter ISAL20F-06 is both leaking minimal water onto the Multiport Valve assembly AND putting considerable filter sand into my pool. My thoughts is that the Plug and Gasket 14965-0028 has gone bad and replacement will correct both problems. I ask for your Professional thoughts and any suggested additional parts that might be needed when replacing 14965-0028. I am assuming that all laterals are still intact at this time. Much thanks for your response
 Reply

A  Answered on 5/22/2020 by InyoPools Product Specialist Patrick P.

Yes normally this is a bad spider gasket which cuases sand back to the pool and this 14965-0028 diverter with spider gasket is what you will need for your JSAL20F-06 Filter.
 Reply


?     Asked on 9/28/2020by Dave Buttwell

hi guys the spider gasket on my sta-rite multi-position valve (14965-0021) needs replacing. do I need to replace the whole rotor assembly? many thanks Dave
 Reply

A  Answered on 10/30/2020 by InyoPools Product Specialist Hector F.

Hi Dave, for the Pentair multiport valve model 14965-0021 this rotor does have to also be replaced. 
 Reply


?     Asked on 5/23/2021by benny

i have a T-240BP-1 sand filter and it leaks water in the filter position when running.will replacing thepump head key or rotor w/ gasket key part #14965-0028 solve my issue and is it compatiable part to fit my filter
 Reply

A  Answered on 5/23/2021 by InyoPools Product Specialist Patrick P.

Hi benny, yes this is the proper part and should fix the issue of water leaking in the filter position.
 Reply


?     Asked on 6/28/2021by Patricia Ayers

Will this fit a T-210WF Sta- Rite filter?
 Reply

A  Answered on 6/28/2021 by InyoPools Product Specialist Patrick P.

Hi Patricia, A few different models of valves were used on the T-210WF filter, if you have the WC112 series valve (the valve should be marked with a model # on the label) then this is the correct part for your valve.
 Reply


?     Asked on 6/29/2022by Salvador Cisneros

can you order the gasket separate? if so, what is part number?
 Reply

A  Answered on 6/29/2022 by InyoPools Product Specialist Craig C.

Hello Salvador.  The Diverter Gasket is not available as a separate item for the Pentair/Sta-Rite WC112 Series Multiport Valve.  The Diverter Gasket and Rotor are a one-piece replacement.    Rotor w/ Gasket - 14965-0028
 Reply