Part # 4679-12
Manufacturer Code 14965-0028
Dimensions 5-1/2" x 4-3/8"
USED ON STA-RITE WC112-148 TOP MOUNT 1-1/2" VALVE GASKET NOT AVAILABLE SEPERATELY 4 SPOKE GASKET . 5-1/2" (ROTOR) ..... DIMENSIONS OUTSIDE DIAMETER: 5-5/16" (GASKET) CENTER HOLE INSIDE DIAMETER: 7/8" (GASKET) SPOKE THICKNESS: 3/16" (SIDE TO SIDE) OUTSIDE RING THICKNESS: 3/16" (SIDE TO SIDE) TOTAL HEIGHT: 4-1/4" (ROTOR) . 7/8" (ROTOR)
I have an AquaTools valve, Model #WC112-147, WC112-148. Are AquaTools, Pentaire and Stay-Rite all the same? Will this part work for my model?
Reply
Hi Al, This part will work with your WC112 Series Valve. AquaTool and Sta-Rite have been acquired by Pentair.
Reply
I turned the rotor while the pump was running. There are no obvious breaks or cracks in any assembly. The only thing I observed was the yellow spider gasket seemed to have deterorated with pieces scattered about. Symptoms were the waste port was running a trickle of water when the valve was on filter. Looking for suggestions.
Reply
Hello John, If you have a trickle of water running out of your waste line while your pump is running on filter you need to replace that spider gasket piece. Rotor, W/gasket 4679-12 this type goes to a Sta Rite Multiport 1 1/2" WC112 Series.
Reply
Will this part fit a Sta-Rite 53185 filter?
Reply
We show this part as being for a Hayward slide valve SP410X. To further cross reference the parts for your filter you can call in to provide the filter model number and or send in images through our support request page. The model number you providsed boes not crossreference in our system not google.
Reply
Is this spider gasket what I need when I am replacing the port assy on sta rite t-210wf with port 261186?
Reply
Hi, Brenda. This Rotor, w/Gasket - 14965-0028 will only work with the WC112 Series valve. If you have the 261186 valve then you can use the MPV 1.5" Tune Up Kit - APCK1067 or the Diverter Gasket - 271104.
Reply
Less than 1 hr
Screwdriver, Nut Drivers, Pliers, Hammer and pin
First I check chlorine and PH levels. Then I backwashed the filter and left it running all night long because it was not clear. I checked the filter rotor gasket and that was damaged. Changed the piece and it fixed the pool water in 12 hours.
Less than 1 hr
Screwdriver, Socket Set, Wrench Set, Hammer, nailset
1 Look at instructions on Inyopools.com.
2 Detach plumbing from multi port valve
3 Unbolt multi port valve by using a screw driver and C wrench or socket. Set aside bolts and nuts.
4 Lift valve off of filter
5 Photograph the position of the valve handle on top and corresponding rotor/gasket position on bottom for reference when reassembling.
6 Set the valve face up on a towel or other soft surface and depress the ring with your feet, which causes the spring on the rotor to compress and the handle to raise up.
7 Using a hammer and nailset, knock out the pin that holds the handle to the rotor post and set both aside, along with the washer that the handle rides on.
8 Flip the valve over, pull out the rotor with the spring and washers.
9 Transfer the spring and washers to the new rotor w/ gasket.
10 Insert the new part into the valve. Refer to your photograph.
11 Flip it back over, depress the valve again, and reconnect the handle—refer to your photo.
12 Reconnect it to the filter and plumbing.
The Most Helpful Review
1 0
(5 out of 5 stars) Easy to Install and Saved us $$$
Reviewed By: Erin F. from Mt. Pleasant, IA ()
Pros: Easy to install, saves money on replacement parts
Cons: Have to disassemble the top of the filter but it was worth it.
We had a leaky filter and the pool supply store said we needed to replace the entire top of the filter which would have cost over $150. We chatted with an Inyo Technician and he suggested replacing the gasket first. It was easy to install and saved us a lot of money! Thanks!
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Great service!
Reviewed By: Inyo Customer ()
Worked Great!
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Good prices
Was this review helpful to you?
(5 out of 5 stars) Works
Reviewed By: Inyo Customer ()
Works
Was this review helpful to you?
(5 out of 5 stars) Perfect Fit!
Reviewed By: Richard A S. from Muskegon, MI ()
Cons: None
Exactly what I needed. It was a prefect replacement and went in without any problems.
Was this review helpful to you?
(5 out of 5 stars) Rotor with spider gasket
Reviewed By: Robert H. from Buchanan,MI ()
Pros: Online help, speed of delivery and online instructions.
Cons: None.
Ordered part on line and received it in approximately 4 days. I used the web site instructions to perform the removal of old part and installation of the new one. Everything fit correctly and the instructions were clear and accurate. I also had initially used online help desk and they told me what part I needed,part no.and web address to go right to the part I wanted to order. Very pleased with all aspects of this purchase.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Chazz from Guntersville, AL ()
Pros: Order was exact!
Cons: None
Was this review helpful to you?
1 0
(5 out of 5 stars) Hayward Pool Filter Valve
Reviewed By: Louis D. from Fayetteville, GA ()
Pros: Delivery time good
Cons: none
Item arrived on time , and worked fine in the application
Was this review helpful to you?