I have a Hayward Power Flo LX Dual Speed. SP-1525-Z2-EBK
I need a shaft seal assembly. Will item # 5111-03 (SP1500KA) fit this pump.
Reply
Hi Kevin, The replacement Seal Assembly (PSR 2131) will work on your Power Flo LX Dual Speed Pump.
Reply
Will this part be the correct one for Haywood model Sp2607x10?
Reply
Your SP2607x10 is a Hayward Super Pump. Here is a link to the Super pump parts list. See key#11. It lists three options for your pumps's seal assembly: OEM, Generic and Sat water.
Reply
hi i REPLACE THE SEAL ON MY HAYWARD PUMP MODEL SP1510DZIXEHC. I TESTED IT WAS OK WHEN I TIGHTEN THE PROPELLER IT WOULD NOT RUN UNTIL I LOSE THE PROPELLER PLASE ADVISE. THANKS
Reply
Hi Sammy, The shaft seal may be installed incorrectly causing too much tension on the motor.
Reply
I have a Hayward Power flo Matrix 1hp Model SP1510-Z-1-XESC that has water coming out back of pump by on/offswitch. Im thinking seals are needed but do I also need the "O" ring. Im having trouble loosening the screws that attach to the second (ceramic) seal.
I need part # for seals and "O" ring if needed. Also any suggestions on how to remove 4 screws from rear of motor
Reply
That sounds like the shaft seal has gone bad. If that is the case then water has already got to your motor bearings and your motor will fail soon as well.
Reply
I have a similar situation, so given your response, would it do any good to replace the shaft seal in terms of cost and labor?
Reply
I have a Swim Pro SP1524-Z-1-EFTC and the impeller has broken off at the threads. It looks like I need the impeller SP1500L and a seal. What is the correct seal to go with this, there are 3 options? Thanks!
Reply
Hi, Bill E. You can use anyone of the three pump seals listed. The OEM, Heavy Duty or Generic pump seals will all fit.
Reply
I have a 1980's Caldera/Balboa spa. The pump/motor is an Aqua Flo-Flo Master HP - model 02115000. The motor shaft is 1/2". Is the psr2131 the correct seal?
Reply
Yes, the 5110-03 PSR2131 Shaft Seal is compatible with the Fmhp Spa Pump, 1.5hp, 2-speed, 120 Volts (02115000) - 02115000-1010
Reply
I have an Aqua-flo Tub-Master "TMCP2" series pump. Model #93560700. Will these seals work?
Reply
Hi, Nick. Yes, this Seal Assembly - PPSR-2131 Shaft seal will work with the Aqua-Flo Tub-Master.
Reply
I have model #SW15941fttlfp is this the right seal assembly?
Reply
Hello, Do you know the brand and the model of the pump? If you are unsure, can you please send a side view picture of the entire pump?
Reply
We have a Magnetek/Century motor part # 1778094, catalog number BN25. Will this seal work?
Reply
Hi Gary, for us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Will this fit model number SP 5610
Reply
Hello, for us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Our sta-rite just buzzes when turned on, the shaft turns but won’t spin when turned on.
Your catalog says the above is the right motor, however ours is a 1.5hp and I think is a dual speed pump.
What pump would you suggest and will our impeller fit on this pump too.
Thank you
Hello Greg. According to the photos you provided your pump motor is a single-speed model. The appropriate replacement is the Century 1.5 HP model BN35v1. Century 1.5 HP Thru-Bolt 48Y Motor - BN35V1 When replacing a pump motor it is also recommended that the motor shaft seal, pump gasket, and O-ring be replaced. These parts are available in a tune-up kit, JWPA Seal Kit 1 & 1.5 HP - APCK1187. Sta-Rite JWPA Seal Kit 1 & 1-1/2 HP - APCK1187
Reply
Is this the correct part for a SP15931 CNP?
Reply
Hello Timothy. The correct shaft seal for your Hayward Matrix pool pump is U. S. Seal part number PSR-2131. If your pool is installed with a chlorine generating system (salt pool) the recommended shaft seal is U. S. Seal part number PS-3869. Pump Seal 2131, Heavy Duty PS3869 (Saltwater Pools) - PS-3869
Reply
I have a Hayward super pump and the shaft on the motor is bad and is leaking water out the bottom and I’m trying to find the right seal and I’m not having much luck from my measurements the seal is approximately 3/4” long and the id is 5/8” and the ceramic piece that goes in the housing is 11/2 od and 5/8 I’d could you tell what seal I need and if you have it in stock thanks Mark
Hello. The Pump Shaft Seal 3/4" PS-201 is the correct motor shaft seal for the Hayward Super Pump. When replacing the shaft seal on a Hayward Super Pump it is recommended that the Housing Gasket - G-95 be replaced concurrently. The Tune Up Kit Hayward Super Pump - GOKIT3 contains these parts with the Diffuser gasket, Pump Lid O-ring and lubricant included. Attached please find the Hayward Super Pump exploded parts diagram for reference.
Reply
Looking for the right seal kit for a Hayward SW15851X20TL. What will work.
Thanks
Reply
Hello, we do not have a pre-assembled seal kit for your pump, but we do offer the individual components you need to replace when switching out a motor. For your pump, you would want to replace the shaft seal, the housing oring, the strainer oring, and the lid oring.
Reply