will this fit on sp1592
Reply
Hello, Eugene. Yes, the On Off Motor Switch (spx1500s8) PART # 5271-08 is the correct replacement for the Hayward Matrix Pump SP1590 SERIES. Click here to view the schematic for the Hayward Matrix Pump Parts.
Reply
i have a Power Flo Matrix 1081 Pump system, model SP 1515-z-1-esc. i need a replacement power switch, and you only show one version, part 5271-08. concerned about size, can you please verify that this switch will work on my pump, or provide model available which will work.
Reply
Hi G, This On/Off Motor Switch can be used with the Hayward SP1515-Z-1-ESC motor.
Reply
how to install
Reply
Hello, The switch is pressed into the opening using the tabs on the ends of the switch. To remove the old switch, you will need to squeeze the tabs. We recommend taking a photo of how the switch is wired before disconnecting the wires.
Reply
will this switch (SPX150058) work with my powerflo matrix model no SP15931TLFP 1.5 HP motor? The switch has 3/4 HP stamped on the side and my pump is 1.5 HP.
Reply
Hi, Hal. This On/Off Motor Switch will work with the Powerflo Matrix Pumps.
Reply
My pump has a 3way switch on it but the third position is for programming the on/off timer. Can you tell me what switch i would need?
Thanks
Reply
Hi, Roy. The Switch only for the Hayward Microprocessor Timer - SP1500FT is not sold as a separate part.
Reply
Hello,
I have the Hayward SP1593FTTL pump with the timer module. When I start the pump, it trips the breaker. It's not seized. The motor is able to spin freely. Last summer the timer module stopped working. The pump was able to work without the timer feature.
I suspect that the circuit board went totally bad. I see that the timer module is no longer offered as a replacement part. How do I convert it to use a standard on/off switch?
Regards,
Bryan
Reply
Hi, Bryan. You can reference our How to Wire the 18313301 Switch to 115v Flex-48 2-Speed Motors Guide. You will just disregard the low speed instructions.
Reply
I have a Hayward pump, model # SP5615, that needs a new power switch. Will this one work?
Reply
Hi, Rhonda. This On / Off Motor Switch - SPX1500S8 can be used with Hayward Pumps, I was unable to confirm if it's compatible with your model. Please provide pictures of your pump motor label for verification.
Reply
Is the on / off switch, part number SPX1500S8 used on water pump model # SP5610?
Reply
My PowerFlo Matrix pool pump switch frayed ans apparently burnt out My switch specifics are Carling Technologies 15A 20A 250 over125 Vac and also a # 1410R You have a replacement switch product# 5271-08 manufacturingcode# SPX1500S8 which has all my spec except it has115R on it and mine has 1410R on it Can your part # 5271-8 be used on my pump? or do you have a switch with my exact same specifications?
Reply
Hi, Deborah. Yes, this switch can be used as a direct replacement.
Reply
I have an SP1520-Z-1-EFTC. Will this switch work? Current switch had three positions, one position to set timer mode. Would appreciate knowing available options if this switch isn’t the one.
Thank you very much!
Hi Bob, Yes this would be the correct switch for your SP1520-Z-1-EFTC
Reply
will this fit the HP50TA haywart heat pump pool heater? thank you
Reply
no, the _SPX1500S8 is used on the back of a pump motor. The correct item should be mfg # Smx1101191101 which we do not currently have in our database.
Reply
I have the sp1515-z-1esc and the on/off switch needs to be replaced. I shut the pump off using a receptacle controlled by a switch. My question is can the motor be re wired to eliminate the on/off switch since its not really used
Reply
Hi, Ted. Yes, the motor can be wired to bypass the On/Off Switch.
Reply
I have a sp1514z2s4ec power flow matrix will this switch work with this model? Thank you
Reply
Hello, Yes, this will work with your model.
Reply
No, what you need is a Microprocessor Timer For 48Y F Item #SP1500FT
Reply
Do you have this?
Reply
yes it will
Reply
Hi, my pump (power flo matrix) needs a new rocker switch. how do I install it?
Reply
Hi, Doug. Check out this video, Hayward Power-Flo Matrix Swimming Pool Pump Power Switch Replacement.
Reply
Will this switch work on a Hayward pool pump model sp 5610?
Reply
Hello Gary, yes if you have the HAYWARD POWERFLO MATRIX SP1590 SERIES PUMP the Hayward Pool Products On/Off Motor Switch - SPX1500S8 would be the correct replacement.
Reply
Need to find out what switch and part number I need to buy for Hayward PowerFlo Matrix pool pump.
Hi Karen, The switch on this page is the switch you will require for your pump in your photos.
Reply
will this fit a sp1515-z-1-esc
Reply
Hi John, this On/Off Motor Switch - SPX1500S8 will fit the motor on your Hayward PowerFlo Matrix Pump.
Reply
thank you
Reply
Will this fit a SP1520Z1ESC? And what is the actual name for the pump model # I have?
Reply
Hello. The On/Off Motor Switch - SPX1500S8 is compatible with the motor SP1520Z1ESC as identified in the attached Hayward PowerFlo Matrix Pump exploded parts diagram. The part number SP1520Z1ESC identifies the motor only. This motor is commonly installed on the Hayward PowerFlo Matrix Pump. The pump label would be located on the pump housing as viewed on the attached Pump Housing Matrix - SPX5500C
Reply