$4,838.00
Model # R8450TI-E
Manufacturer Code 016033
Raypak's Heat Pumps feature exclusive DuraSteel powder-coated cabinets, 3 blade swept wing fangs, and a best in class warranty service.
Classic Model Standard Features:
Cabinet Durability
Quiet Operation
Compressor
Titanium Heat Exchanger
Digital Controls - Basic Functions
Digital Control - Built-in Mini Automation
Warranty
2 years Labor and 7 years Parts
10 years on the heat exchanger tube, see warranty for details.
Best in Class Warranty Service Same day in the major cities in Florida, 24-48 hours most everywhere else. Areas outside of Florida are 24 to 48 hours with certain designated major cities having same day service. Check with your Raypak sales person for warranty service details in your area. We try harder!
WARRANTY EXCLUSIONS
This Limited Warranty does NOT apply;
1. if the product has been moved from its original place of installation, or if the original
owner no longer owns the property where the original installation was made;
2. if the product is not properly installed with a pool or spa by a qualified licensed installer in
accordance with applicable local codes and ordinances, good trade practices, and the
manufacturer’s installation instructions;
3. if the rating plate(s) or serial number(s) are altered or removed;
4. if the product is modified in any way, or non-factory authorized accessories or other
components are used in conjunction with the product;
5. to damage, malfunctions or failures resulting from failure to properly install, operate or
maintain the product in accordance with the manufacturer’s instructions;
6. to damage, malfunctions or failures from abuse, act of nature, accident, fire, flood, freeze,
lightning or the like;
7. to damage, malfunctions or failures resulting from [or due to] connected system control
devices;
8. performance problems caused by improper sizing of the heater or electric service
voltage, wiring or fusing;
9. use of any attachment, including any energy saving device not authorized by the
manufacturer.
10. to damage, malfunctions or failures from misuse or neglect, including but not limited to,
freeze-ups, operating the heater with the cabinet door off, having flow restrictions or
obstructions between the heater outlet and the pool/spa, or not maintaining a proper
chemical balance (PH level must be between 7.4 and 7.8 and total alkalinity between 100
and 150 PPM. Total dissolved solids (TDS) must be no greater than 3000 PPM)
Can the chiller option be added to this heat pump after installation?
Thanks, R Corley
Reply
Unfortunately, there is no way to " Add-on " the chiller aspect to this heat pump. They are either heat pumps OR heat / cool pumps.
Reply
Hi, does this model have a reversing valve for power defrost? Thanks
Reply
Hello, Will. The Raypack R8350TI-E does not have a reversing valve for power defrost. If offers Power Frost that Allows the heat pump to operate in colder weather by keeping the heat exchanger tubes from developing frost. When the air temp drops below about 45F, the unit will shut down because there isn't enough heat in the air to allow for productive operation. Raypak does offer model PS9350ti with Rapid Defrost. Areas that are subject to lower ambient temperatures have a tendency to cause ice to build up on a heat pump's condensing coil. The Professional heat pump uses a patented refrigerant management system to rapidly defrost the heater. (The PS9350ti) currently is a Special Order item.
Reply
What is the difference between Raypack M8350ti-E-HC and M8350ti-E .
Reply
Val, The difference between the R8350TI-E-HC Raypak Standard 133K BTU Digital Heat Pump W/ Chiller and the R8350TI-E Raypak Standard 133K BTU Digital Heat Pump is that the R8350TI-E-HC has a chiller so it can cool the pool in the warmer months whereas the R8350TI is just a heater.
Reply
Under the "Warrenty Exclusions" section what does the statement
"This limited Warrenty does NOT apply"
Is there a Warrenty if so what is it?
Reply
Bob- Where it says "Warranty Exclusions" and then goes on to say "This Limited Warranty Does NOT Apply" it then goes on and lists reasons that would void the warranty or are not covered under warranty. The warranty on this heat pump, per Raypak, is as follow: If the Heater is installed in a single-family residential dwelling, the Applicable Warranty Periods are: two (2) years for labor and seven (7) years for parts, with no labor coverage in the third through seventh years. Notwithstanding the foregoing, the titanium tube component of the titanium heat exchanger is warranted for 10 years from the Effective Date, with no labor coverage in the third through tenth years. If the Heater is installed anywhere other than a single-family residential dwelling, the Applicable Warranty Period for the Heater and its parts is limited to only one (1) year, parts and labor.
Reply
Hi,
I am considering between the RS8350ti-E-QT Vs RS8350ti-E. Can you tell me the DB rating on both units. I read some place that e-qT is 59DB and need to confirm both and any other difference between the 2 besides 125K VS 133K output.
Thanks
Reply
Hi, The RS8350ti-E-QT operates at a dB of 59, the dB rating is not listed for the RS8350ti-E but it will be higher than 59.
Reply
Less than 1 hr
Sled
2 0
This was placed on a pallet in the driveway. It is extremely hard to move, definitely not a one person job. We ended up using a hot tub sled to slide it through the grass to get it to the backyard. Most dealers will let you rent theirs for cheap, or even come help you do it. Be aware they do just ship it to the driveway, so have plans on how to move it to the final location before delivery.
2 to 4 hrs
Screwdriver, Nut Drivers, Pliers, Wrench Set
3 0
The 1400,000 btu heat pump was delivered on time and the delivery guys put the heater in my garage. it’s fastened to a pallet and needs to go in the back yard about 70 feet away so I took the wheels the pressure washer and bolted them onto one end of the pallet one on each side. Now I need handles .the other end of the pallet I slid in 3 2x3x8 screwed one on each side and 1 in the middle . With the help of my neighbor we wheeled in to place. I thought this might help someone save a few bucks . The heater is working great. Thanks Inyo pools
2 to 4 hrs
Wrench Set
3 0
Not very hard to install this unit just alot of thinking... also I went to salt system this year. Valves and Plumbing Plus check valve was approximately 175 dollars... not including salt.. I installed this on a 30 ft round pool 54 inch high...will review again when pool water is at 86 degrees in new jersey beginning middle of may..
More than 8 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Fish Tape
3 1
Poured a extra slab and upgraded sub panel to 100 amp service. Plumbing Heat Pump after install is not a hard task if your a DYI person. Install looks great and works great. Highly recommend the raypak heat pump. My pool is a 18x36 Inground.
2 to 4 hrs
Screwdriver, Dolly, Strap wrench, Miter saw, tapw measure
5 0
Removed electrical and plumbing from old unit
Remove the old unit
Used a dolly to move the new Heat Pump inot place
Removed access panel and connected to the existing electrical wiring
Replaced access panel
Re-worked the plumbing to attach to the new heat pump
tightens all pipe connections
Turned on pump, checked for leaks
Verified the pump was increasing water by 10 degrees
2 to 4 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Adjustable Wrench
2 2
Hello All,
It is fairly easy for the mechanically savvy. Turn off the power! ***If you are not comfortable working with electricity, Then STOP now! You should have an electrician or pool repair company do this project!
I wired the Heat pump system into and existing 220v connection I had for a Hot Tub. Make sure to use the correct gauge wiring or you'll have a bigger problem. This unit uses around 10,000 watts of electricity according to my energy monitoring system. It is a power HOG! Easily will use $10 a day in power. Runs for 8 hours when my pump is on.
Make sure to purchase the Heat Pump pad for the unit to sit on.
Most of this project truly is PVC plumbing. Pipes have to be cut and retrofit with existing plumbing.
There is no one story that will tell you how to do that, you just have to dive in. Make sure you use appropriate cleaner and glue. Measure twice and cut once. I used a miter box saw to make my cuts so it was a lot faster and had square ends on the pipe. Let the glue dry for a hour or so before turning the system back on!
2 to 4 hrs
Screwdriver, Nut Drivers
1 0
Awesome company very reasonable prices & fast delivery. If you're looking to install a heat pump these are the guys to call. Very helpful pleasant customer service.
More than 8 hrs
Screwdriver, Pliers, Hack Saw
5 0
The user/installation manual was easy to follow. If you are comfortable gluing up PVC pipe and can correctly wire up a 220vac supply to the unit, you will not have any problems. My programming of the unit was very simple, since I was not trying to control any pumps or auxiliary equipment from the unit. However the manual gives detailed instructions on how to add these items.
We live in Tennessee so I'm hoping we will be able to use our pool through late September early October.
Inyopools.com was great to work with. After the order was placed they discovered they were out of stock on a flow meter I had ordered for this install. They called me and told me the issue, then recommended a replacement that was a little cheaper price, which was great. Everything arrived on time without any problems. I will definitely order from them again.
The Most Helpful Review
16 2
(5 out of 5 stars) Very Nice Pool Heater
Reviewed By: Barry A. from Cincinnati, OH ()
Pros: Heats pool quicker than expected
Cons: None so far
Heats my pool better than I expected, I was hesitant to buy a heat pump, but I am very happy with the results. Too soon to know the cost, but it doesn't run all the time.
Was this review helpful to you?
The Most Recent Reviews
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Awesome! Get ready for a jump in the power bill! haha.
Was this review helpful to you?
1 0
(5 out of 5 stars) Swimming in January!
Reviewed By: Inyo Customer ()
I bought this heater a little over a year ago. I wired and installed myself, plumbed it myself, and I have to say it’s one of the best moves I’ve ever made for my pool. I couldn’t be happier with the results.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Works great, heats out pool in the FL winters to 86 easily. About $10/day on the electric bill though
Was this review helpful to you?
1 1
(3 out of 5 stars) read reviews and have realistic expectations
Reviewed By: Inyo Customer ()
I was expecting a better performance from a heat pump in AZ but this unit cycles into defrost every few minutes and has run for a week and has not been able to get the pool to a decent temp . A call to Raypaks tech line was just a waste of time and he contradicted the facts stated in the manual , basically said I should shut it off until may , it can't work at ambient temps below 50 and water below 70 ,, hope it at least extends our summer swimming
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
So far so good. Easy to use and gets my pool warm.
Was this review helpful to you?
1 0
(5 out of 5 stars) Much better than swimming in cold water
Reviewed By: Inyo Customer ()
Does what it is supposed to do. It was larger than I expected, like a big a/c unit, which was my only complaint.
Was this review helpful to you?
2 0
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
It works fine just hope it lasts
Was this review helpful to you?