$4.13

Qty:

Details

Top

Part # 4700-02X

Manufacturer Code E-2-S1

Dimensions 2.06" L x 0.3" W x 0.3" D

Alternate Part #'s 1117, 14426308R, 14971SM10E2, 2603102012, 271164, E2S1, HAY0612111, SP710XZ7, SPX0710XZ7, SPX710XZ7, WC3058, 27-253-1004

Product Description

Replacement Handle Pin for Hayward SP0714T Valve

This is the replacement handle pin for the Hayward SP0714T Valve. This is the pin which secures your valve handle, this is the pin only and not the valve handle.

Easy Homeowner Installation

View our Guide on How to Replace a Hayward Backwash Valve Handle

Commonly Used On

  • SP0714T
  • Hayward Pro Series Sand Filters
  • Hayward Top Mount Sand Filters
  • Hayward S166T
  • Hayward S180T
  • Hayward S190T
  • Hayward S210T
  • Hayward S220T
  • Hayward S230T
  • Hayward S244T
  • Hayward S270T

 

Top

?     Asked on 5/31/2016by mike

does this pin fit the pentair mutli port sm 20 valve?
 Reply

A  Answered on 5/31/2016 by InyoPools Product Specialist Lennox H.

Hi Mike, This Handle Pin can be used with the SM20 Valve.
 Reply


?     Asked on 6/25/2017by Jude

What are the dimensions of this pin for the handle of the multiport. Are there two pins in the handle. I have a pin coming out one side and am not sure if it broke in the middle inside handle or were there two? One coming out each side of the handle?
 Reply

A  Answered on 7/4/2017 by InyoPools Product Specialist Lennox H.

Hi, Jude. This Pin is .3" x 2.06" and only one pin is required. 
 Reply


?     Asked on 7/10/2017by Greg

Hi, I have some plastic pieces that have dislodged from the handle that is stopping the handle correctly closing in the selected position and water is leaking down the backwash pipe. Does the pin do anything else than hold the handle in place? I'm thinking if I remove the pin, remove the handle then remove the obstacles, the pin should simply reattach through the handle without issue. Am I correct??? Thanks
 Reply

A  Answered on 7/12/2017 by InyoPools Product Specialist Lennox H.

Hi, Greg. It sounds like the washer has broken and would need to be replaced. To replace the washer you would need to remove the pin from the handle. 
 Reply


?     Asked on 9/14/2018by Jimmy

I have the same problem as Greg in July of 2017, where the handle does not sit properly and the backwash tub leaks. Which washer is it exactly that I would need?
 Reply

A  Answered on 9/15/2018 by InyoPools Product Specialist Lennox H.

Hi, Jimmy. You will need to check your valve to confirm that the Nylon non-metallic Bearing is intact. If its not, it will need to be replaced based on the model of your valve. 
 Reply


?     Asked on 5/11/2019by Peter M

on a splash pak sand filter ss160 how do I remove the pin on the dial valve handle. thank you Peter M
 Reply

A  Answered on 5/11/2019 by InyoPools Product Specialist Lennox H.

Hi, Peter M. The valve model is required in order to provide you with the proper instructions.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers, Adjustable Wrench

1     0

Multiport Valve was leaking to drain when in recirculate position

Written on 9/15/2020 by Guest

After replacing the gaskets inside the valve. removed the old handle by tapping the old pin out and then put the new handle in place and inserted pin to hold the replacement handle in place.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.67  out of 5 stars)
3 Rating
5 star:
 
(2)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)