Part # 4600-3241
Manufacturer Code 273241
Dimensions 16.25" L x 2.5" W x 2.5" D
Pentair OEM Slide Valve Piston Rod Assembly for Pentair Filters - 273241
INYO # 4600-3241 PENTAIR # 273241 GENERAL DESCRIPTION: THIS IS THE COMPLETE SHAFT WITH SPACERS, HANDLE, AND TOP CAP AND WASHER USED ON THE PENTAIR 26-1165 PUSH PULL VALVE GENERAL INFO MATERIAL: SHAFT: BLACK PLASTIC SPACERS: BLACK PLASTIC TOP CAP: WHITE PLASTIC (INCLUDED WITH THIS ITEM) HANDLE: BLACK PLASTIC (INCLUDED WITH THIS ITEM) DIMENSIONS: LENGTH: 16-3/8" (INCLUDING HANDLE) LENGTH: 13" (A) (WITHOUT HANDLE) SHAFT DIAMETER: 9/16" (B) (AT THE HANDLE END,TAPERS DOWN TO 7/16" AT THE OTHER END SPACERS: TOTAL # 2 SPACERS INCLUDED DIAMETER: 1-15/16" THICKNESS: 15/32" FROM OUTSIDE TO OUTSIDE GROOVE: 5/16" SPACING: (MEASURED ON CENTERLINE FROM FIRST SPACER WITH THE FIRST SPACER AT ZERO) 1ST 0 2ND 7-1/2" SPACER O-RINGS: (NOT INCLUDED WITH THIS ITEM) THESE ARE STRETCHED ON TO THE SPACERS SO THE DIMENSIONS SHOWN ARE FOR THE ORIGINAL O-RINGS BEFORE THEY ARE STRETCHED OUTSIDE DIAMETER: 1-7/8" INSIDE DIAMETER: 1-1/2" HOLES IN SHAFT: (MEASURED ON CENTERLINE FROM THE HANDLE END OF THE SHAFT) HOLE: 3/16" AT 5/16" FROM END INCLUDES: THIS IS BASICALLY THE ENTIRE VALVE INTERNAL AND HANDLE ASSEMBLY SHAFT WITH 2 SPACERS (ALL ONE SINGLE MOLDED PIECE) TOP CAP, TOP WASHER, HANDLE, POSITION BRACKET, COTTER PIN, SPACER O-RINGS, TOP O-RING MARKINGS: "PISTON ASSEMBLY 27-3241" MOLDED ONTO THE SHAFT
*******************************************************************************
TOP PLATE INFO INCLUDED? INCLUDED INYO # 4600-3077 PENTAIR # 273077 GENERAL DESCRIPTION: THIS IS THE TOP PLATE USED IN THE 26-1165 PENTAIR PUSH PULL VALVE MATERIAL: WHITE PLASTIC SHAPE: THIS IS ROUND WITH A SLOT IN THE TOP. DIMENSIONS: DIAMETER: 2-3/8" (A) TOTAL HEIGHT: 15/16" (B) CENTER HOLE DIAMETER: 9/16" INCLUDES: TOP PLATE ONLY MARKINGS: "OPEN" AND "LOCK" WITH ARROWS MOLDED ON TOP
*******************************************************************************
HANDLE INFO INCLUDED? INCLUDED INYO # 4600-3089 PENTAIR # 273089 GENERAL DESCRIPTION: THIS IS THE HANDLE USED ON THE PENTAIR 26-1165 PUSH PULL VALVE MATERIAL: BLACK PLASTIC SHAPE: T STYLE, WITH COTTER PIN HOLE IN THE SIDE DIMENSIONS: LENGTH: 3" (A) WIDTH: 3/4" HEIGHT: 3-1/4" (B) INCLUDES: HANDLE ONLY MARKINGS: NO MARKINGS
*******************************************************************************
how to remove piston rod assembly
Reply
Hi Leon, You can find the dissembling instructions in the Pentair Slide Valve Owner's Manual.
Reply
I need to purchase the piston valve assembly for the pentair 263064. Will this fit? If not, please direct me to the product that will fit. I replaced this valve (the backwash valve) once before using inyo to purchase the part...but it seems harder to find the right product/model fit this time. thanks
Reply
Hi, Joe. The Piston Shaft Replacement Kit - 263055 is the correct assembly for the Pentair Valve 263064.
Reply
Do you sell a kit with just the washers? My piston rod assembly (27-3241) is fine but the washers are beginning to wear out. If you have just the washers, I would be interested in a purchase. If so what would be the cost and process?
Reply
Hello Jeffery- Here is a link to the Pentair - Pac Fab 2" PVC Slide 26-1165 Parts page. I would recommend viewing that page to see the different part options we have available. I am confident we have the parts you are looking for.
Reply
Does this piston rod assembly fit the Pentair FNSP60? If not, do you sell the assembly?
Thank you
Reply
As long as the valve used is the model 261165 then this piston rod would work. At one point that valve model was used on your model filter.
Reply
Less than 1 hr
Socket Set
This was an easy replacement. The directions that were included were very clear. All I needed was a 3/8 wrench to remove the 2 screws that hold the piston assembly in place. Then pull the assembly out of the housing. The kit came complete with new orings and silicone lube. Lube all the orings and reassemble. 30 minute job!
The Most Helpful Review
2 0
(5 out of 5 stars) Perfect Piston Rod Assembly
Reviewed By: LeAnne S. from Edwardsville, IL ()
This piston rod assembly was inexpensive and came ready to be installed immediately - we were up and running in 5 minutes!
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Perfect replacement
Reviewed By: Jim S. ()
Exact replacement for what I needed. Came complete with new orings and silicone lube. Easy to replace.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Excellent product great service
Was this review helpful to you?
(5 out of 5 stars) Piston Rod replacement
Reviewed By: Don K. from Irving, TX. ()
Cons: tricky to remove old rod
I was struggling to get the rod to move in any direction, and could NEVER get it locked... Put the new rod in after lubing the rings and it worked flawlessly..!
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: John C. from Cave Creek, AZ ()
Pros: Great prices and product definition.
saved a ton of cash by ordering this part and replacing it myself. I will definitely use InyoPools for parts in the future.
Was this review helpful to you?
1 0
(5 out of 5 stars)
Reviewed By: Rick M. from Lilburn, GA ()
The part was an exact replacement to the one that was replaced. I thought the price was a little steep for some plastic and o-rings.
Was this review helpful to you?