?     Asked on 5/4/2015by Roman

Hello,how long we have warranty if we buy this product and what including and how work this warranty.
 Reply

A  Answered on 5/4/2015 by InyoPools Product Specialist Andy O.

Roman- The warranty for the 460932 is a 2 years parts and labor, 10 years on compressor parts and labor, lifetime on the titanium heat exchanger. The warranty is only valid if you have it installed by a Qualified installer, and if not Pentair will only warranty the parts for 60 days. Here is the link to the warranty card: http://www.pentairpool.com/pdfs/LimitedWarrantyCard.pdf
 Reply


?     Asked on 5/9/2015by jay

What is the amp draw on 108000 heat pump?
 Reply

A  Answered on 5/12/2015 by InyoPools Product Specialist Patrick P.

Hi Jay, I don't have the exact amp draw but do have a bit of information for the required breaker which may helpful. Min. Circuit Ampacity: 42 amps, Recommended Fuse Size: 50 amps, Max Fuse Breaker Size: 70 amps.
 Reply


?     Asked on 5/22/2015by Scott

Is the Pentair 108,000 heat pump just as quiet as other top brands?
 Reply

A  Answered on 5/23/2015 by InyoPools Product Specialist Patrick P.

Hi Scott, Yes the Pentair heat pump would be just as quiet as Hayward, Jandy, AquaCal & Raypak.
 Reply


?     Asked on 6/22/2015by Yannick

How much for shipping to canada.H7p6e7 zip code
 Reply

A  Answered on 6/23/2015 by InyoPools Product Specialist Lennox H.

Yannick, We're unable to ship the Pentair Heat Pump UltraTemp 108,000 BTU outside of the continental USA, you will need a Freight Forwarder to get it into Canada.
 Reply


?     Asked on 5/2/2016by Inyo Visitor

What is the weight of the unit? What kind of base does INYO or Pentair recommend to put the unit on?
 Reply

A  Answered on 5/4/2016 by InyoPools Product Specialist Alan M.

Hi, the weight of the Pentair Heat Pump UltraTemp 108,000 BTU is approximately 300lbs. Per Pentair's owners manual, the heat pump would need to  be installed on a level surface. You can use an equipment pad or other materials, like pavers or blocks, as long as the base is stable and will not deteriorate over time.
 Reply


?     Asked on 5/10/2016by Justin

Is this heat pump compatible with above ground pools?
 Reply

A  Answered on 5/10/2016 by InyoPools Product Specialist Hector F.

Yes you can use these models for above ground pools as well.
 Reply


?     Asked on 7/6/2016by boden

What year model is this?
 Reply

A  Answered on 7/10/2016 by InyoPools Product Specialist Lennox H.

Hi Boden, This is a current (2015-2016) manufactured UltraTemp model.
 Reply


?     Asked on 12/19/2016by jm

will this heat pump heat a 288 square ft pool?
 Reply

A  Answered on 12/19/2016 by InyoPools Product Specialist Adam Y.

Good morning Jim, Before I answer can I have the actual dimensions h,w,dth? to get gallon size. I will be able to give you a better answer.
 Reply


?     Asked on 2/28/2017by jim

how many btu,s do i need to heat a 2114 gallon pool
 Reply

A  Answered on 2/28/2017 by InyoPools Product Specialist Scott W.

You would be good with the 70,000 BTU model for 2114 gallons, part number 460930.
 Reply


?     Asked on 4/6/2017by Inyo Visitor

What size heater do I need for an in-ground 18 x 36 25,000 gallons?
 Reply

A  Answered on 4/6/2017 by InyoPools Product Specialist Scott W.

You would want a heat pump in the 125,000-140,000 BTU range depending on what state you reside in.
 Reply


?     Asked on 5/17/2017by Lauren

Hello- What size heat pump would I need for a 15,000 gallon inground? We have a deep-end going to 6.5ft and a shallow tanning ledge but in total 15K gallons (15x35).
 Reply

A  Answered on 5/20/2017 by InyoPools Product Specialist Lennox H.

Hi, Lauren. I would not recommend a unit smaller than a 108/110K BTU unit, you can always use a bigger unit which will heat the pool faster.
 Reply


?     Asked on 8/2/2017by Don

How big and amps do I need for about 5000 gallon in ground pool ? My pool company says 96,000 an d are trying to sell me a tropical one for 3000.
 Reply

A  Answered on 8/4/2017 by InyoPools Product Specialist Lennox H.

Hi, Don. A 5,000 gallon pool depending on the location, desired temperature, and heating rate can use a 50K-100K or higher BTU unit. If they are recommending a 96K BTU unit, that requires like a 50 amp 230 volt breaker. This 108K unit will also be sufficient. 
 Reply


?     Asked on 10/29/2017by Jay

Heater is working, cannot increase the temp. It will decrease temp only.
 Reply

A  Answered on 10/30/2017 by InyoPools Product Specialist Lennox H.

Hi, Jay. The Autoset Board Bezel Label Assembly - 472734 is probably bad and will need to be replaced. 
 Reply


?     Asked on 10/8/2018by Mike

How much room around the unit must be free of shrubs, fences, etc.? Do you have a list of approved installers in or near the 20878 zip code (around Rockville, MD)? How much might a typical installation cost, excluding electrical? Thanks. -- Mike
 Reply

A  Answered on 10/9/2018 by InyoPools Product Specialist Joe S.

The heat pump must be placed to provide clearances on all sides for maintenance and inspection. 1. At least 24 in. [61cm] access must be available in the front and 24 in. [61 cm] on all the other sides of the heat pump for service and proper air flow, see Figure 2. 2. If the heat pump is to be installed under a cover or under a vertical overhang, the unit must have a minimum of six (6) feet [1.83 m] clearance from the top of the heat pump. 3. Install a minimum of five (5) feet [1.52 m] from the inside wall of the pool or spa unless the heat pump is separated from the pool or spa by a five (5) foot high solid fence or other permanent barrier. Canadian installations require a minimum of three (3) meters from pool water.
 Reply


?     Asked on 1/5/2019by FR

We want the best ultra temp heat pump Pentair model that draws the lowest cfm of air because our plan is to install the heat pump's air intake grill inside our 6,400 cu.ft. wind-free R2 clear structure and have the top of the unit exhausting to outside the pool enclosure without any obstructions. We are in Springfield, MO and will use the pool year round and, if need be, buy an Ameri-Dome Heater to increase the ambient temperature and bring in 530cfm air. Please advise on Pentair cfm intake

 Reply

A  Answered on 1/10/2019 by InyoPools Product Specialist Lennox H.

Hi, FR. We do not have the CFM rating of the UltraTemp Heat pumps. Pentair was also unable to provide us with this info.
 Reply


?     Asked on 3/27/2019by Rolando

que tipo de bomba de calor ocupo para una alberca de 7mts x 5mts y profundidad de 1,80.
 Reply

A  Answered on 4/10/2019 by InyoPools Product Specialist Michelle B.

Hello, Is there anything I can help you with today?
 Reply


?     Asked on 4/25/2019by Tom

I have a easytouch and the instructions to connect this heat pump are not clear, do I wire from the gas heater terminal which is 2 wires, to which spade connectors since there are 3 terminals , spa/com/pool ?
 Reply

A  Answered on 4/26/2019 by InyoPools Product Specialist Lennox H.

Hi, Tom. If your  EasyTouch software version is 1.11 or higher, you can use the RS-485 communication connector using Pin 2 and Pin 3. Otherwise you will have to use the Gas Heater terminal on the EasyTouch to the 3 Wire Remote Terminal on the Heat Pump control board. 
 Reply


?     Asked on 9/27/2019by Peter

The temperature is showing 102 when the water temp is 90. How can I replace the sensor 471566 in this Pentair 460932.
 Reply

A  Answered on 10/3/2019 by InyoPools Product Specialist Steve M.

Peter, we apologize for the inconvenience, however, our technicians are not certified by Pentair to advise on the replacement of the parts within the Pentair Pool Products UltraTemp 110 Heat Pump 108,000 BTU - Almond. We suggest contacting the manufacturer directly and speaking to their technicians. Pentair can be reached by calling 800.831.7133. 
 Reply


?     Asked on 4/6/2020by Scott

I have an pentair heat pump 110 will auto heat and cool I can’t find it anywhere?
 Reply

A  Answered on 4/7/2020 by InyoPools Product Specialist Lennox H.

Hi, Scott. This model will only heat. The UltraTemp 120 H/C - 460935 is the only UltraTemp model that will heat and cool. 
 Reply


?     Asked on 5/2/2020by Charles Gilmore

How fast should the heat pump bring temp up to a reasonable pool temperature
 Reply

A  Answered on 1/8/2021 by InyoPools Product Specialist Hector F.

Hi Charles, there are a few variables to consider when calculating pool heating time. Here is a guide that we put together called "How Long Does It Take to Heat a Pool?" that may assist in calculating that. 
 Reply


?     Asked on 5/23/2020by Dave H

Will the Pentair 110 work for a unground pool with 35,000 gallons of water in lower Michigan
 Reply

A  Answered on 12/30/2020 by InyoPools Product Specialist Hector F.

Hi Dave, the UltraTemp 110K BTU model may have some difficulty heating the water so I would suggest the UltraTemp 143K BTU model
 Reply


?     Asked on 9/7/2020by Inyo Visitor

where is the closest company that services Pentair Pool Heat Pumps?
 Reply

A  Answered on 12/18/2020 by InyoPools Product Specialist Hector F.

Hello, most CPC(certified pool contractor) will work on these however there are some Pentair authorized service centers that you can confirm on the Pentair website
 Reply


?     Asked on 9/16/2020by Richard Haan

My pool is 10,000 gal which size heat pump is best for me? Thanks
 Reply

A  Answered on 9/16/2020 by InyoPools Product Specialist Robert M.

Hello Richard - Something around 110K btus would be sufficient for 10,000 gallons. 
 Reply


?     Asked on 11/15/2021by Inyo Visitor

Can i use this pump in 17000 gallons pool
 Reply

A  Answered on 11/16/2021 by InyoPools Product Specialist Rich N.

You can, but we might recommend something a little larger.  Check out our guide on How to Select an Inground Pool Heater to be sure you don't need a larger one.  An easy way to estimate the temperature rise (and the correct size for your pool) is to calculate the surface area of your pool and check it out against the temperature rise on the table in the link.   
 Reply