?     Asked on 2/16/2012by Guest

I just finished replacing the shaft seal on my booster pump. As soon as I turned the pump on water was leaking from the shaft seal. Is it defective or am I doing something wrong?
 Reply

A  Answered on 2/16/2012 by InyoPools Product Specialist Patrick P.

Depending on the model, the installation of a booster pump shaft seal can be slightly different than a pool pump shaft seal. Some booster pump and pool pump shaft seals require that a silicone sealant be used on the outer areas of the metal seat of the shaft seal. The seal will need to be lightly hammered into the body of the pump. You can use a 1 inch PVC coupling or a piece of 1 1/4 inch PVC pipe and a rubber mallet. This procedure will apply to any pool pump or booster pump using a >PS-1000 style shaft seal.
 Reply


?     Asked on 4/30/2016by Jose Luis Castanon

I am replacing the pump on a pentair. Which wire goes where?
 Reply

A  Answered on 5/2/2016 by InyoPools Product Specialist Lennox H.

Hi Jose, You can review our How To: Wire a Pool Pump for wiring instructions.
 Reply


?     Asked on 5/23/2016by Lynn Ballew

does this come with a gasket
 Reply

A  Answered on 5/23/2016 by InyoPools Product Specialist Patrick P.

This motor does come with the small rubber slinger gasket that goes over the shaft but it does not come with the shaft seal or pump gaskets. We would strongly recommend the Whisperflo Shaft Seal and Gasket Kit when replacing your motor.
 Reply


?     Asked on 6/30/2017by Inyo Visitor

my model #1777474 will this fit
 Reply

A  Answered on 7/2/2017 by InyoPools Product Specialist Alex V.

Hello, Please provide us with the model number on the pump housing. The model number you provided does not show in my system. 
 Reply


?     Asked on 1/17/2018by Clement

Hi, Can this motor be an upgrade replacement for the motor in WhisperFlo WF26 with the original motor being 1.5hp 1.1 S.F. 8-177475-20? Thanks.
 Reply

A  Answered on 1/17/2018 by InyoPools Product Specialist Lennox H.

Hi, Clement. This OEM motor can be used as an energy efficient option. The THP is the same just uses less energy. 
 Reply


?     Asked on 2/26/2018by James

I need to replace the capacitor on a pentair motor #196239 (motor package no 355022s. My old capacitor is a genteq 27L1358. can you tell me if this is the right capacitor. Not sure its hard to reed the old one. Thanks James
 Reply

A  Answered on 2/27/2018 by InyoPools Product Specialist Lennox H.

Hi, James. The 30 MFD 370 VAC Run Capacitor - 5VR0303 is the correct replacement for your motor. 
 Reply


?     Asked on 5/18/2018by Kam

Hello, just replaced my old motor with this one. Claned the flters and added DE. When I first started the motor, I was running at 15 psi. When I tried to vaccum, there was weak suction and pressure went to 20 psi. There's very weak jet at the inlet too. I took the hose off and just ran it off the skimmer and it's still weak. What happened?
 Reply

A  Answered on 5/18/2018 by InyoPools Product Specialist Lennox H.

Hi, Kam. I would recommend that you check your filters. They may need to be cleaned thoroughly. 
 Reply


?     Asked on 8/11/2018by Kenneth Baldwin

I have a Pentair WFE-4 Pump for my pool 011513 is the part number. (1 HP 1.65 SF HP 208-230/115V 60 Hz 3450 PRM Self Priming Pump.) It's getting very loud and I think it is s on it's last leg. Will the WhisperFlo OEM Motor WFE-4 be the right one to replace it with and compatable? Will I need an electrician to install this part?
 Reply

A  Answered on 8/18/2018 by InyoPools Product Specialist Lennox H.

Hi, Kenneth. Yes, this WhisperFlo OEM Motor - 071314S is the correct replacement motor. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT. The replacement can be done by a layperson 
 Reply


?     Asked on 8/13/2018by steve

I replaced the compasitor and cleaned all filters, still overheating and shutting off. is the motor shot and should I replace pump and motor.
 Reply

A  Answered on 8/18/2018 by InyoPools Product Specialist Lennox H.

Hi, Steve. Yes, the issue may be caused y the motor windings. I would recommend replacing the motor. 
 Reply


?     Asked on 10/7/2018by Carl

How can I tell if my pump or my motor is bad? I am hearing what sounds like a grinding noise that vibrates the whole system so it is hard to localize the sound. I have good water flow. I have attached the sound.
 Reply

A  Answered on 10/8/2018 by InyoPools Product Specialist Lennox H.

Hi, Carl. Since your still getting good water flow, the motor is the issue and will need to be replaced. 
 Reply


?     Asked on 11/2/2018by Scott Burdsall

Looking to replace pool pump. (its DOA). Will this work as a replacement for a Pentair whisperflo?

 Reply

A  Answered on 11/2/2018 by InyoPools Product Specialist Lennox H.

Hi, Scott. Yes, this OEM Motor - 355010S is the correct replacement. You will also need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT
 Reply


?     Asked on 11/4/2018by Tami

Our motor is out on our pump and I put in the model number & it says no match. Can you please help me find the correct motor for this pump? WF-26 / 011773 Model No. 177475
 Reply

A  Answered on 11/5/2018 by InyoPools Product Specialist Hector F.

You can use either motor model PL2854 or the B854
 Reply


?     Asked on 12/2/2018by Keith

I have wfe-4 011513 with motor #177450. This is a 1hp motor. What replacement motor would I use? Thanks for your help. -Keith
 Reply

A  Answered on 12/3/2018 by InyoPools Product Specialist Hector F.

You can use this replacement order or you can use this motor model B841
 Reply


?     Asked on 2/10/2019by Dennis Cossins

Do you also stock and sell the bearings for this motor? If so, are they OEM or a cheap Chinese knockoff? Thanks
 Reply

A  Answered on 2/11/2019 by InyoPools Product Specialist Michelle B.

Hello, Unfortunately, we would not carry those bearings for that specific motor.
 Reply


?     Asked on 3/30/2019by jim carlyle

is this a compatible replacement motor for 177449-03
 Reply

A  Answered on 3/30/2019 by InyoPools Product Specialist Lennox H.

Hi, Jim. This motor will not, you will need p/n 355008S (OEM) or B2661 (Generic).
 Reply


?     Asked on 6/14/2019by DAVE

I have a Pentair SF-N1-1A / 340038 1 HP SF HP 1.25 60HZ I'm having trouble locating a replacement motor. What motor should I use? Thanks

 Reply

A  Answered on 6/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Dave. The replacement motor you can use is P/N 355020SB2853, or  PL2853. You will also need the SuperFlo Tune Up Kit - GOKIT78
 Reply


?     Asked on 6/22/2019by Brooks Marsh

need to replace pump WF- 26 011773
 Reply

A  Answered on 6/23/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the proper motor your pump will need, http://www.inyopools.com/Products/44400017084597.htm
 Reply


?     Asked on 7/18/2019by Byron

WFE-24 Motor# 196232 of which I need a replacement. I have already purchased a tune up kit. Thank you so much for your help!
 Reply

A  Answered on 7/18/2019 by InyoPools Product Specialist Hector F.

The replacement motor is the model B852.
 Reply


?     Asked on 8/4/2019by AO

Hello, our motor needs replacing for the Pentair Whisperflo WFDS-4 motor #193508 1 HP / 2 speed pump. Which motor and associated parts are needed? Thank you for your help.

 Reply

A  Answered on 8/4/2019 by InyoPools Product Specialist Lennox H.

Hi, AO. The B2982 motor along with the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need. If you're using an external timer, you will not need the Toggle Switch and Canopy Kit for 56Y 2-Speed - 2512558-001 which is sold separately. 
 Reply


?     Asked on 8/4/2019by Michael

I am looking for the replacement motor for WFDS-24/012485. 2 speed pentair. The Motor # is 193936. Thanks
 Reply

A  Answered on 8/6/2019 by InyoPools Product Specialist Joe S.

Good day, yes the Pentair OEM Motor WFE-4/WF-26 1HP Almond - 355010S would be the correct motor for the Pentair Whisperflo Dual Speed Up Rate 1 HP Pump
 Reply


?     Asked on 8/6/2019by Tony

I have the pentair pool pump model wfe-26. I bought at a garage sale. It did not have the capacitor. What is the proper capacitor I need to get?

 Reply

A  Answered on 8/6/2019 by InyoPools Product Specialist Matt S.

The 196233 motor uses the Run Capacitor - 50 MFD (RD-50-370)
 Reply


?     Asked on 8/10/2019by Christina Emerson

Looking for a motor for a Pentair 011013, PMP Intelliflo VS3050 serial number 0332129080072D.
 Reply

A  Answered on 8/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Christina. The replacement motor for your pump is P/N 350105S.
 Reply


?     Asked on 8/22/2019by Albert Acosta

Need a replacemet motor for my wisperflow part number 7-177450-03

 Reply

A  Answered on 8/23/2019 by InyoPools Product Specialist Joe S.

Based on the information provided Pentair OEM Motor WFE-4/WF-26 1HP Almond - 355010S or you can use A.O. Smith 1 HP Square Flange 56Y Full Rate EE Motor - B2841V1.
 Reply


?     Asked on 9/10/2019by Ian

I have a WFE-4/011513. Motor#196233 1HP, which is making a loud whining noise but is operating normally, can it be repaired or do I need to replace it. If it has to be replaced can you suggest which motor I require

 Reply

A  Answered on 9/12/2019 by InyoPools Product Specialist Hector F.

Most commonly that is due to the bearings failing however if there is significant corrosion then it may not be worth repairing. I would suggest inspecting first and if the face of the motor and its body is in good condition to then consider replacing the bearings. 
 Reply


?     Asked on 9/12/2019by Ken

I need a pump for a pentair wf-26/ 011773
 Reply

A  Answered on 9/17/2019 by InyoPools Product Specialist Michelle B.

Hello, This will be the replacement motor you will need. http://www.inyopools.com/Products/03000017000395.htm?Keywords=b2854
 Reply


?     Asked on 9/24/2019by Tommie Lynn Sullivan

I have the same motor as Ian in a previous question but mine is leaking. There is significant corrosion so I want to replace. I can’t find on your website can you direct me ?

 Reply

A  Answered on 9/24/2019 by InyoPools Product Specialist Hector F.

You can use either single-speed model B854 or the B848. Essentially both are the same however to save a few dollars just go with the B854. 
 Reply


?     Asked on 10/19/2019by dennis

am replacing the motor on a wfe-6 pump what motor replaces it
 Reply

A  Answered on 10/21/2019 by Industry Professional

THE REPLACEMENT MOTOR FOR A WFE-6 1.5HP IS 355012S .
 Reply


A  Answered on 10/21/2019 by Industry Professional

The WFE-6 is a full rated 1-1/2hp. Use 35-126-1226

 Reply


?     Asked on 2/6/2020by Peter

Looking for a Pentair WFDS-4 part number 011486 1 hp 230v do you have one in stock and whats the price?
 Reply

A  Answered on 2/7/2020 by InyoPools Product Specialist Steve M.

Peter, Inyo Pool Products no longer sells the OEM Pentair WFDS-4 motor. The direct replacement would be the Century 1.0 HP Square Flange 56Y Dual Speed Full Rate Motor - B2982
 Reply


?     Asked on 3/23/2020by Tony

I am looking to replace my 6 year old Pentair pump motor. The pool is a small inground with under 10,000 gallons. I would like to run a pump that is more economical. Perhaps a 2-speed or variable speed motor. I am located just south of Raleigh, NC. Thank you

 Reply

A  Answered on 3/23/2020 by InyoPools Product Specialist Patrick P.

HI Tony, We would suggest this Variable Speed Replacement Motor as the proper replacement motor for the pump included in your photos. You will also need a Pentair Super Flo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 4/17/2020by Christopher Mills

I have a pentair whisperflo wfe-24 and the motor seized. I want to make sure I order the correct replacement motor. he oem part on my pump motor is 011517. What is the correct replacement and any other accessoires I need to install it such as gaskets etc

 Reply

A  Answered on 4/17/2020 by InyoPools Product Specialist Patrick P.

Hi Christopher, You will actually need this B2661 Replacement Motor this motor is a 3/4 HP Full Rate Motor where your Motor is a 1 HP Up Rate Motor but this motors are identical as they have the same True HP as the Full Rate Motor has a higher service factor. The math works as follows 1 HP Up Rate x 1.25 Service Factor = 1.25 True HP and 3/4 HP Full Rate x 1.67 Service Factor = 1.25 True HP. You will also need a Pentair WhisperFlo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 4/26/2020by Mike

I have a Foxxx pump. the nameplate states: pump model FXWF-24 / 340007 motor # 177474 HP 1.0. See photo for nameplate. Do you have a direct replacement?

 Reply

A  Answered on 11/4/2020 by InyoPools Product Specialist Hector F.

Hi Mike, the correct replacement motor for your motor part number 177474 is the model 5231X. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply


?     Asked on 4/28/2020by Donald P Gabel

I NEED TO REPLACE A 1 HP WISPER FLO MOTOR CAT SERIAL BW6-275 . PART 8-177450-.03 WHAT MOTOR DO I NEED.
 Reply

A  Answered on 11/4/2020 by InyoPools Product Specialist Hector F.

Hi Donald, the correct replacement motor for motor part number 177450 is the B841. You will also need a Pentair Whisperflo seal kit when you replace your motor. For a chlorine swimming pool, it is the GOKIT32 and for a saltwater pool, it is the GOKIT32SALT. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/5/2020by Robert Koch

Have a Pentair whisperflo #196233 wfe-4 Need replaced is this a correct replacement?

 Reply

A  Answered on 12/9/2020 by InyoPools Product Specialist Hector F.

Hi Robert, the correct single speed replacement motor for the motor included in your photo is the B841. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/8/2020by Ralph

Will this motor fit my WFDS-26 Pentair pump? What other parts do I need to make a switch?
 Reply

A  Answered on 1/6/2021 by InyoPools Product Specialist Hector F.

Hi Ralph, the correct single speed replacement motor for the original WFDS-26 pool pump is the B2854. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/8/2020by Ralph

Will this motor fit my WFDS-26 Pentair pump? What other parts do I need to make a switch?
 Reply

A  Answered on 1/20/2021 by InyoPools Product Specialist Hector F.

Hi Ralph, the correct replacement motor for the motor on the WFDS-26 model pool pump is the B2982. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/11/2020by nate

I am trying to find a replacement for the motor, but there are a few options and I want to make sure I replace it with the correct one.

 Reply

A  Answered on 1/6/2021 by InyoPools Product Specialist Hector F.

Hi Nate, the correct single speed replacement motor is the B853. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest provide those using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply


?     Asked on 5/16/2020by Pamela Menzies

I need to replace my Pentair pump motor. WFE-4 / 0115133 1 HP 208-230/115v motor -196233 self priming 10'
 Reply

A  Answered on 12/4/2020 by InyoPools Product Specialist Hector F.

Hi Pamela, yes, this is the correct single speed replacement motor for the original pump model 011513. You can also use the motor model B841. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/21/2020by Anric

Hi guys, I need a replacement motor for my pentair sf-n2-1a/340042 - see picture specs attached, as the slow speed functionw orks great but on high speed - the motor gets very hot and stops running after a few minutes - can you advise a replacement pump that is easy to install, many thanks

 Reply

A  Answered on 5/21/2020 by InyoPools Product Specialist Hector F.

Your replacement dual speed motor replacement will be the model B2982 that you can view by clicking here and if you need the seal kit that will be the GOKIT78 that you can view by clicking here
 Reply


?     Asked on 5/22/2020by Jason

Hi Guys, I need a replacement motor for Pentair Model 340038 (single stage) and wondering if you can help me with the proper replacement motor? Also, could I put a dual stage motor into the existing housing? I ordered a new pump and now I'm thinking I should have just ordered a replacement motor because the plumbing is horrible and would be really tough (see pic). Thanks for your help!

 Reply

A  Answered on 5/22/2020 by InyoPools Product Specialist Patrick P.

Hi Jason, The direct replacement for your motor will be this motor here http://www.inyopools.com/Products/03000017039421.htm if you want to go Energy Efficient then a variable speed 1.65 HP shown here is your best option http://www.inyopools.com/Products/00200017074679.htm if you go the variable motor option then we would suggest upgrading your impeller to this 1.5 HP impeller http://www.inyopools.com/Products/07501352019651.htm so you can take advantage of the higher HP range of this motor. Regardless if you go with the single-speed motor or the variable speed motor you will also need this seal kit here http://www.inyopools.com/Products/00500005003532.htm?Keywords=gokit32 
 Reply

  • Commented on 5/22/2020 by Product Owner

    Thanks for the recommendations. Which seal kit would work for saltwater pool?
     Reply

    • Commented on 5/23/2020 by InyoPools Product Specialist Patrick P.

      Hi Jason, I'm glad I looked at this again as my original suggestion was on a Whisperflo and you have a SuperFlo. You will still need the same motor(s) but the seal kit will be this SuperFlo Seal Kit which will work on salt. And you will need this Diffuser and this Impeller if you go with the Variable Speed. Please note these are different parts then suggested in the original reply.
       Reply

  • Commented on 5/22/2020 by Product Owner

    Typically with a variable speed motor you can expect an operational cost savings between 50% - 75% compared to a single speed motor. We put together this article which goes more in depth on the operational cost savings http://www.inyopools.com/Blog/how-much-does-my-pool-pump-cost-to-run/ Please note the variable speed motor can only be wired 230V
     Reply


?     Asked on 5/23/2020by John Cary

I have the WhisperFlow pump P/N 011513 as shown in the first image, with the motor, WFE-4/011513, shown in the second image. The system is making loud noise, perhaps like a bad bearing, so I assume the motor. The sound is like that at https://www.troublefreepool.com/threads/pentair-whisperflo-loud-noise.130687/. Do you agree that this is the motor? What will it cost to replace? Thx.

 Reply

A  Answered on 5/23/2020 by InyoPools Product Specialist Megan C.

Hi John, Yes this sounds like bad bearings and we would suggest replacing your motor. You would require this B2841 Replacement Pool Motor You will also need a Pentair Whisperflo Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply

  • Commented on 5/27/2020 by Product Owner

    Thanks. Is it possible to replace with a variable-speed pump?
     Reply

    • Commented on 5/27/2020 by InyoPools Product Specialist Patrick P.

      Hi John, yes you could upgrade to this Variable Speed Replacement Motor this will work with the pump in your photos. We did write this article which shows the Cost Savings between a Variable Speed Pump and Single Speed Pump which you may find helpful. One note.. if you do have an automated control system like the IntelliTouch, EasyTouch, AquaLink, ProLogic, etc.. then that system will power the pump on and off and then the onboard digital controller would take over from there as far as the speeds go. You would program all of the speeds directly on the motor controller.
       Reply

      • Commented on 7/21/2020 by Product Owner

        I have exact same motor (Pentair Whisperflo 011513 w/ 1 HP 1.65 S.F. motor 177450) and need to replace it. I have Pentair EasyTouch 4 controller. Is it possible w/ this variable motor and EasyTouch controller: If in Spa mode or Spillway mode, always run the pump at full speed. If in Auto mode and it's on Pool (ie. timed pool circulation), then allow downstep to low speed Or do I need to upgrade to IntelliFlo so full EasyTouch control (which I wouldn't bother doing). Or stay single speed.
         Reply

        • Commented on 11/9/2020 by InyoPools Product Specialist Megan C.

          If you replace the current single speed with the V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU it is compatible with the automated system. The Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 or GOKIT32SALT for salt pools. 
           Reply

      • Commented on 5/27/2020 by Product Owner

        I do not have one of those systems. Would be interested in how I can control through an app. Are these able to communicate wirelessly? Bluetooth? Thx.
         Reply

        • Commented on 5/27/2020 by InyoPools Product Specialist Patrick P.

          Hi John, By purchasing this V-Link Kit you can control through your phone. Unfortunately, this item is out of stock for the season with the manufacturer but you can always add after the installation of the motor. Here is a Video on the V-Link that we put together that you might find helpful.
           Reply


?     Asked on 5/24/2020by gary wicker

I have a pool pump model no./part no. SF-N1-/4A/340037 HP 3/4 S.F.HP 0.94 What model do I need to replace the current motor?
 Reply

A  Answered on 12/29/2020 by InyoPools Product Specialist Hector F.

Hi Gary, the correct single speed replacement motor for the motor on the Pentair SuperFlo 340037 is catalog number B852. You will also need a Pentair SuperFlo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 5/26/2020by Lee

I need to replace my existing WhisperFlo 1HP motor. This motor/pump supports a waterfall feature. Would it be more efficient and save electricity costs over time by replacing this single speed pump/motor with a variable speed pump? I suppose the question is which is more energy efficient? A single-speed 1HP pump or a variable speed pump running at 1HP?
 Reply

A  Answered on 10/22/2020 by InyoPools Product Specialist Hector F.

Hello, so a variable speed motor replacement will always be much more energy-efficient than a single speed. It can potentially save up to 80 percent of the electrical consumption compared to your current motor. We would just need to know your current motor part, model, or catalog number to confirm a compatible replacement for you.   
 Reply


?     Asked on 5/30/2020by Inyo Visitor

is this the same as the 355020s
 Reply

A  Answered on 10/20/2020 by InyoPools Product Specialist Hector F.

Hi Irvin, unfortunately, no these are different model motors. Basically, the 071314S is stronger than the 355020S by approximately .5 hp. because it is a 1 HP full rated motor. Here is a blog that we put together that can further explain those details called "How To Understand True Pump Horsepower - Up Rated vs Full Rated"
 Reply


?     Asked on 7/20/2020by Brian

Hi I'm looking to replace the motor labeled in the photo. Would you please let me know what replacement motor is compatible? Thank you.

 Reply

A  Answered on 7/21/2020 by InyoPools Product Specialist Lennox H.

Please click here to be directed to the B2748 being the direct single speed replacement for your motor.
 Reply

  • Commented on 7/21/2020 by Product Owner

    Thanks! Also, what other kit(s) will be needed to install this properly.
     Reply

    • Commented on 8/27/2020 by InyoPools Product Specialist Lennox H.

      Brian, You will need the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT
       Reply


?     Asked on 8/3/2020by Inyo Visitor

I need to replace my: Pentair 1.0 hp 1.65 S.F. Hp Model # WF-4 Part # 011580 3450 rpm What is the replacement? Coker
 Reply

A  Answered on 12/11/2020 by InyoPools Product Specialist Hector F.

Hello, this is the correct replacement motor for your motor model but is currently out of stock or you can use the B848. You will also need a Pentair Whisperflo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 8/13/2020by tim garigliano

will this fit a 3/4 hp motor?
 Reply

A  Answered on 10/29/2020 by InyoPools Product Specialist Hector F.

Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 10/22/2020by Gerard Friebe

Does this motor work with a Pentair 340039 pump
 Reply

A  Answered on 11/2/2020 by InyoPools Product Specialist Hector F.

Hi Gerard, yes this motor can replace the motor on your original motor on the Pentair Superflo pump model 340039 however, you can also use the motor model B854. We recommend replacing the seal kit as well when replacing a motor. The GOKIT78 is the correct one for your Pentair Superflo. 
 Reply


?     Asked on 11/1/2020by Juan Samartin

I have a WFE-4 Whisperflo filter, the service factor is 1.65, Serial # is 1-02-C04 - will this pump motor work for my application. I'm in California. Please advise. Thanks
 Reply

A  Answered on 11/3/2020 by InyoPools Product Specialist Joe S.

Good day, Juan, we would recommend the Century 1.0 HP Square Flange 56Y Full Rate Motor - B2848 and the Tune Up Kit Pentair/Purex Whisperflo - GOKIT32.
 Reply


?     Asked on 11/10/2020by Stephen Dischler

I have a Pentair HP 1.0 60HZ WF-24 Part # 011772 which is making loud grinding noises which I assume is bad bearings. I would like to just change the motor to a quieter motor not the entire system. What do I need?
 Reply

A  Answered on 11/10/2020 by InyoPools Product Specialist Joe S.

Hello Stephen, based on the 011772 we would recommend the V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU and the Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 .
 Reply


?     Asked on 11/11/2020by RICKH

What pump motor should i use on my Pentair FSN48 to replace the old burnt one? This is the second one, the first came with the filter and the one now is a Century SQ112 1hp. It only lasted 2 years. Please help!!!
 Reply

A  Answered on 11/12/2020 by InyoPools Product Specialist Joe S.

Hello Rick, based on the information provided we would suggest a new pump. To replace yours we would recommend the Whisperflo Pump 1 1/2 HP - WF-26 and using the Pump Union, 2"NPT x 2"SLIP - 11201-0154 for an easy install. Once motors start failing quickly there could be issues with the pump housing, seal plate, impeller that is adding stress to the motor or might have a defect causing water to enter the motor.
 Reply


?     Asked on 11/27/2020by GERRY META

Need to replace this superflo pump due to screeching bearings. Can you tell me what motor and kit I need? This pump is used to run a waterfall on my grotto.

 Reply

A  Answered on 11/30/2020 by InyoPools Product Specialist Hector F.

Hi Gerry, the correct replacement motor for the motor included in your photo is the 5231X. You will also need a Pentair SuperFlo seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
 Reply


?     Asked on 4/19/2021by Heath

I need to replace the motor for my pool pump. Could you confirm which motor is the correct one?

 Reply

A  Answered on 4/20/2021 by InyoPools Product Specialist Matt S.

The correct replacement motor for your model (196233) is the 1.0 HP Square Flange 56Y Full Rate EE Motor - B2841V1.  The necessary gasket kit for the Pentair / Purex Whisperflo is the GOKIT32 or the GOKIT32SALT
 Reply


?     Asked on 5/13/2021by Roger Burava

I have a PENTAIR PUMP Cat# WFE26 011518 I need a new motor for this unit. I guess old motor # 177450.
 Reply

A  Answered on 5/13/2021 by InyoPools Product Specialist Robert M.

You could use this motor to replace your 011518. We also have a black version of this motor at a cheaper cost. The part number is B2841V1. It is a 1HP full rated energy-efficient motor but it has the same total HP rating as your 1.5HP uprated motor.
 Reply


?     Asked on 9/3/2021by Victor

Need replacement motor for Pump Model #WFE-4/011513. Motor number is 177450
 Reply

A  Answered on 9/3/2021 by InyoPools Product Specialist Craig C.

Hello Victor.  The Century Motors 1.0 HP Full Rate EE Motor model B2841V1 is a compatible replacement motor for the Pentair Pool Pump model WFE-4, and motor model 177450.  Century 1.0 HP Square Flange 56Y Full Rate EE Motor - B2841V1   It is recommended that the motor shaft seal, seal plate gasket and diffuser o-ring be replaced concurrent with the motor.  The GOKIT32 contains the necessary parts to complete this project.  Tune Up Kit Pentair/Purex Whisperflo - GOKIT32
 Reply


?     Asked on 10/4/2022by Jonathan

I have a Pentair WFE-24 part no: 011517 that just died. The motor was getting louder and louder with a metal on metal noise. What is correct replacement motor?

 Reply

A  Answered on 10/5/2022 by InyoPools Product Specialist Hector F.

Hi Jonathon, yes this is the correct OEM replacement motor for your model WFE-24 pool pump. You can also use the B853 and the standard chlorine pool seal kit for you pool pump model is the GOKIT32. I have also emailed you a quote that you can convert to an order if you would like. 
 Reply


?     Asked on 3/21/2023by Del Albright

Does this come with the impeller?
 Reply

A  Answered on 3/25/2023 by InyoPools Product Specialist Hector F.

Hello Del, unfortunately these do not come with the impeller. For your model WFE-4/WF-26 the part number for the impeller is 5074-27B
 Reply