?     Asked on 10/16/2016by Doug

I have a SP2607C impeller and a SP 3005R impeller ring. The ring does not fit over the impeller. What is the correct part for the impeller ring?
 Reply

A  Answered on 10/18/2016 by InyoPools Product Specialist Lennox H.

Hi, Doug. The Hayward SP2607C impeller does not require an impeller ring. If you can provide the model number of your pump I can verify if you have the correct parts.
 Reply


?     Asked on 12/29/2016by joe

does this come with installation instructions
 Reply

A  Answered on 12/29/2016 by InyoPools Product Specialist Stacey M.

Hello Joe, your impeller ring is going to go on your impeller before it goes into the diffuser.  There are how to's on our website under Pool pumps on how to clean and replace.
 Reply


?     Asked on 4/4/2017by Gary

My Hayward RS1000 pump developed a leak so I am replacing the shaft seal assembly and the housing gasket. Upon disassembly, I found some wear between the impeller and the impeller ring. Is this a concern and should these items be replaced as well? What are the liabilities of not replacing the impeller and impeller ring? Thanks
 Reply

A  Answered on 4/5/2017 by InyoPools Product Specialist Stacey M.

Hello Gary, any wear and tear you see on your impeller and ring this could cause leaks and or break apart during your pump running, which could cause more damage.
 Reply


?     Asked on 10/19/2017by Inyo Visitor

Should there be an impeller ring between a sp3010-c impeller and a sp3000-bn diffuser on a Hayward super 2 ?
 Reply

A  Answered on 10/19/2017 by InyoPools Product Specialist Lennox H.

Hi. Yes, this Impeller Ring - SPX3005R is required. 
 Reply


?     Asked on 5/20/2019by Joseph Marx

I'm putting together an order to rebuild a Hayward Super II pool pump and have been talking to Lenox who was going to get me info on the impeller ring. Upon further investigation, the old ring has a sharp edge worn into it which mirrors an edge on the impeller housing. Does this mean the entire housing should be replaced? What is comparative cost of rebuild vs. purchasing a new pump?
 Reply

A  Answered on 5/21/2019 by InyoPools Product Specialist Patrick P.

Hi Joseph, When you say impeller housing are you speaking of item #6 (diffuser) on this Hayward Super II Parts Break Down if yes then you would need to replace your diffuser ($29) and not your pump housing. Based on the parts Lennox quoted and this diffuser the cost of a rebuild is $122.44 if you did determine you need the Super II Pump Housing ($221) the rebuild price would be $343.44 compared to $549 for a Complete 1.5 HP Hayward Super II Pump. If you go the complete pump route then you might consider the PureLine Prime 1.5 HP Pump at $379 this has been a great pump for us. The ports on the PureLine Prime are not in the exact location as the Hayward Super II so you would have some minor re-plumbing but nothing major.
 Reply


?     Asked on 7/23/2019by Delina Barrera

Does the following order require the ring? Diffuser, 35-5270 Pac Fab (355270) 5002-06B & Impeller, 35-5315 Pac Fab (355315) 5002-05C?
 Reply

A  Answered on 7/23/2019 by InyoPools Product Specialist Hector F.

The parts that you are ordering are for the Pentair/Pac Fab Challenger series pool pump which does not use impeller rings. 
 Reply


?     Asked on 4/15/2020by Kevin Mulligan

Does the hayward sp3007x10az use an impeller ring between the diffuser and the impellar.
 Reply

A  Answered on 4/15/2020 by InyoPools Product Specialist Hector F.

Yes, this pump model would use the impeller ring part number 5110-23 that you can view by clicking here
 Reply


?     Asked on 5/10/2020by Ken Cranford

When I tried to install this part it was too large. Therefore I installed the impeller without it. I am getting a lot of bubbles. After resealing leaks around the jets and weir door intakes (for the bubbles) I am thinking the seal should go back in but I don't know where it's supposed to go. Please send a diagram for my issue. Thanks
 Reply

A  Answered on 1/19/2021 by InyoPools Product Specialist Hector F.

Hi Ken, for us to provide the parts diagram could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo or quickest using our live online chat feature. Once we get this photo we can provide the proper parts diagram for your pump. 
 Reply


?     Asked on 8/9/2021by John carro

Am replacing a Hayward Super pump motor with a Century from you. Don’t see a impeller ring. Is it missing or never came with one? What would be proper replacement if needed. Thanks.

 Reply

A  Answered on 8/9/2021 by InyoPools Product Specialist Stephen B.

Thank you for contacting Inyo Pools, The super pump does not have an impeller ring.
 Reply


?     Asked on 8/9/2021by John carro

Am replacing a Hayward Super pump motor with a Century from you. Don’t see a impeller ring. Is it missing or never came with one? What would be proper replacement if needed. Thanks.
 Reply

A  Answered on 8/10/2021 by InyoPools Product Specialist Stephen B.

Thank you for contacting Inyo pools, This pump does not require a impeller ring.
 Reply


?     Asked on 4/18/2022by Brian

I'm replacing my pool pump motor B2979 7-k56ab47a01-05 and I don't see an impeller ring. Did I lose it I can't remember --- Impeller is SP3021-C.. Do I need one ? Then I'll need to order one. Don't see one in my GO-Kit2 package.
 Reply

A  Answered on 4/19/2022 by InyoPools Product Specialist Craig C.

Hello Brian.  The Impeller Ring for the Hayward Super II Pool Pump creates a small running clearance between the impeller and the pump casing without causing wear to the impeller or pump casing material.  The impeller ring inhibits water from recirculating back to suction from the impeller discharge, maintaining efficient water flow.  The Impeller Ring for the Impeller SP3021C is SPX3021R   The Impeller Ring is not included in the GOKIT2.   The correct orientation of the Impeller Ring is the smaller circumference is placed first over the impeller nose.  Reference exploded parts diagram, part key 7.       Hayward Super II
 Reply


?     Asked on 5/18/2022by Christopher

Hi I'm looking for the impeller ring for a sp2610x15 or does it not require one? The impeller is a sp2610-c
 Reply

A  Answered on 5/19/2022 by InyoPools Product Specialist Craig C.

Hello Christopher.  The Hayward Super Pump model SP2610X15 does not require an impeller ring for the impeller model SP2610-C.  Attached please find the Hayward Super Pump exploded parts diagram for reference.
 Reply


?     Asked on 6/15/2022by Scott D. Campbell

Does this ring fit the Impeller for the Hayward SP2607X10
 Reply

A  Answered on 6/15/2022 by InyoPools Product Specialist Craig C.

Hello Scott.  The Hayward Super Pump model SP2607X10 does not utilize an Impeller Ring.  The Impeller Ring is utilized on the Hayward Super II SP3000 Series Pool Pumps.  Attached please find the Hayward Super Pump exploded parts diagram for reference.
 Reply


?     Asked on 3/30/2023by John M Dobson

Will Pureline Impeller Ring Replacement Compatible with Select Hayward Pumps, 0.75HP-3.0HP - SPX3005R fit my Hayward pump which is model SP3207X10?

 Reply

A  Answered on 4/3/2023 by InyoPools Product Specialist Hector F.

Hello John, the correct impeller ring for your Hayward Tristar pump model SP3207X10 is part number 5110-23A
 Reply