?     Asked on 1/25/2012by Guest

How do I change the shaft seal on my pool pump?
 Reply

A  Answered on 1/25/2012 by InyoPools Product Specialist Patrick P.

Changing the shaft seal is quite simple. Here's How To Replace a Pool Motor Shaft Seal.
 Reply


?     Asked on 7/10/2014by Guest

Will this shaft seal work on an ARNESON poolsweep, model 1093014400 with 1081 pool motor?
 Reply

A  Answered on 7/10/2014 by InyoPools Product Specialist Patrick P.

Yes this shaft seal does work on an Arneson Pool Sweep
 Reply


?     Asked on 11/12/2014by Inyo Visitor

One measurement on your description says 1.25". Looking at the picture the hole is 5/8" so what is the 1.25"? This looks like my seal but nothing on my 5/8" seal measures 1.75". Looking at the proportions on the picture nothing looks 1.75"
 Reply

A  Answered on 11/12/2014 by InyoPools Product Specialist Alex V.

The 1.25" measurement refers to the outside diameter of the shaft seal.
 Reply


?     Asked on 12/17/2014by Inyo Visitor

Is there any thing special when installing this seal?
 Reply

A  Answered on 12/17/2014 by InyoPools Product Specialist Robert M.

Our guide on "How To Replace a Pool Motor Shaft Seal" will detail the instructions for the shaft seal.
 Reply


?     Asked on 6/4/2015by Mickey Moryl

Looking for replacement seal and orings for Optiflo Plastic Pump Model CPT-N!-1.5 part # 454545 & 357255
 Reply

A  Answered on 6/4/2015 by InyoPools Product Specialist Patrick P.

Hi Mickey, You would require the shaft seal on this page for the Optiflo pump. For the o-rings you would need a quantity of two of the 357 O-ring and a quantity of one of the 223 O-ring.
 Reply


?     Asked on 6/17/2015by Chris

Will this seal work on a Blue Devil B8386. I've been searching for a week and have found nothing yet. If it does not work can you point me in the right direction? THX, Chris
 Reply

A  Answered on 6/19/2015 by InyoPools Product Specialist Lennox H.

Chris, Based on the information found this Pump Seal 200 (PSR 200) will work on the Blue Devil Pump.
 Reply


?     Asked on 9/28/2015by ANDY

Will this seal kit fit aqua flo flo-master xp2 1hp, model#06620000-1?
 Reply

A  Answered on 9/28/2015 by InyoPools Product Specialist Robert M.

Hello Andy - Part number 5250-104 will fit the Aqua Flo Flo-Master XP2.
 Reply


?     Asked on 11/2/2015by mark

Appears I have an older Jacuzzi pump, 94024110. Model looks to be an LR type with model # S1-LR-6-S1. Do you know if it uses this same seal? Thanks!
 Reply

A  Answered on 11/3/2015 by InyoPools Product Specialist Lennox H.

Hi Mark, The Pump Seal 200 5/8" (PSR200) would be the correct seal for the older Jacuzzi LR pumps.
 Reply


?     Asked on 3/31/2016by Stan

Which specific seal kit (generic part number) do I need for QC-1072 pool pump motor? Thank you.
 Reply

A  Answered on 3/31/2016 by InyoPools Product Specialist Hector F.

The seal kits are not based off of the motor model but the model of the front pump housing that the motor mounts to.
 Reply


?     Asked on 3/31/2016by Stan

I have Sta-Rite Pump Model No: P6E6D-205L. Which seal kit (generic part#) do I need for it? The motor that connects to it is QC-1072 (original motor model: K48K2PA105C1). Thank you!
 Reply

A  Answered on 3/31/2016 by InyoPools Product Specialist Hector F.

This model pump is the Max E Pro so the seal kit is part number gokit79.
 Reply


?     Asked on 4/30/2016by Inyo Visitor

Will the psr 200 fit on challenger P./N. 35-5459?
 Reply

A  Answered on 4/30/2016 by InyoPools Product Specialist Scott W.

Yes, that's the generic shaft seal for the challenger.
 Reply


?     Asked on 5/14/2016by paul

Hello, will the psr 200 seal fit my aqua flow 20-0108x , it has a 91693601 impeller, it's a Flowmaster pump model 02110408 serial is 2189059,it has both name brands on it ,just want to order the right one first, thanks
 Reply

A  Answered on 5/17/2016 by InyoPools Product Specialist Lennox H.

Hi Paul, This shaft seal will fit the Aqua flow and Flow Master pumps.
 Reply


?     Asked on 7/8/2016by Inyo Visitor

Will this seal fit my Sundance Theramax II 6500-126 ?
 Reply

A  Answered on 7/13/2016 by InyoPools Product Specialist Lennox H.

Hi, Based on how these pumps are labeled we can only locate replacement part based on the volute part number. If you can provide that number we can confirm if this PSR-200 seal is the correct replacement.
 Reply


?     Asked on 7/18/2016by Inyo Visitor

I have a Challenger 2HP PENTAIR PUMP CF11-N2-2F .Is a PSR200 shaft seal correct? Is a GO-KIT5 the correct repair kit?
 Reply

A  Answered on 7/19/2016 by InyoPools Product Specialist Alan M.

The Pump Seal 200 PSR 200 is the correct replacement shaft seal for the Pentair Challenger Pump.
 Reply


?     Asked on 7/30/2016by Dave

If this part doesn't fit can I return it?
 Reply

A  Answered on 8/1/2016 by InyoPools Product Specialist Lennox H.

Hi Dave, Unfortunately, once this part has been installed it can not be returned. If you can provide us with the manufacturer and model of the pump housing I can try to locate the correct pump seal.
 Reply


?     Asked on 12/25/2016by Robert

does this fit a DuraGlas pool pump/ I have a 56y frame square flange 3/4 hp motor that i am going to replace, i understand that i need to change the seal as well.
 Reply

A  Answered on 12/27/2016 by InyoPools Product Specialist Andy O.

Hi Robert- Unfortunately with the Dura-glas there are a two possible seals that would depend on the age of the pump. You will either need to know if it is pre-1998 or 98-current, or take your pump apart and see if your seal plate has the copper or stainless steel cone or not.
 Reply


?     Asked on 12/28/2016by mark wiemann

What is the difference between PSR200 and PSR200v
 Reply

A  Answered on 12/29/2016 by InyoPools Product Specialist Adam Y.

Good morning Mark, There is no difference.
 Reply


?     Asked on 4/3/2017by Rodolfo Molina

Hi, is this PSR 200 shaft seal will fit a Jacuzzi S15lr6 1.5h pump?. I have been buying different ones but none fit since the form of the base is very particular. Is there a kit for this pump with all the parts to be replaced to avoid leaking? Regards,
 Reply

A  Answered on 4/5/2017 by InyoPools Product Specialist Scott W.

Yes, that would be the correct replacement shaft seal.
 Reply


?     Asked on 4/16/2017by Alex

Hi, is this psr 200 shaft seal will fit a Jacuzzi pump model S1KHMR 9-6 serial # 074322? If not which one do i need? Thanks.
 Reply

A  Answered on 4/18/2017 by InyoPools Product Specialist Lennox H.

Hi, Alex. I was unable to locate a Jacuzzi pump with the model S1KHMR. If you can verify the model number and or send us photos of the pump we can try to identify the pump.
 Reply


?     Asked on 6/8/2017by Robert W

the motor shaft is 1/2 " is this the correct seal?
 Reply

A  Answered on 6/11/2017 by InyoPools Product Specialist Lennox H.

Hi, Robert. The pump seal is specific to the pump housing, I will need to know the model of the pump housing in order to confirm if this pump seal will fit into the seal plate.
 Reply


?     Asked on 6/10/2017by WJ

I have a Jacuzzi pump/ filter model 100-515LRT 9-3-HK6 mfg date 03Feb05 and I need a pump seal 1.5hp
 Reply

A  Answered on 6/13/2017 by InyoPools Product Specialist Lennox H.

Hi, WJ. Based on that model number and mfg date the PSR200 seal will fit.
 Reply


?     Asked on 6/11/2017by Brent Capps

does this fit an optiflo pn 340073sr
 Reply

A  Answered on 6/11/2017 by InyoPools Product Specialist Patrick P.

Yes this is the correct seal for the optiflo 340073sr
 Reply


?     Asked on 6/26/2017by Larry

Hello, I have a leak on the shaft seal on my Optfl N1 1 HP HD Part number 347982 serial # 0360070130040L Date 3/11/13 Site. E I looked online and i want to confirm that the replacement seal is part # 5250 - 104 Mfg code PSR200 5/8" is the correct seal before I purchase it? also is there any other parts I should purchase when I change the seal ? Thanks Larry
 Reply

A  Answered on 7/29/2017 by InyoPools Product Specialist Alex V.

Larry, Yes, this is the correct seal for the Pentair OptiFlo pump. 
 Reply


?     Asked on 7/26/2017by Duane

Will this fit the : C1245
 Reply

A  Answered on 7/26/2017 by InyoPools Product Specialist Alex V.

Duane, The seals are based on the pump housing not the motor. We will need the pump model number. 
 Reply


?     Asked on 8/1/2017by cindy

what are the measurement on the impeller end of the seal ID?
 Reply

A  Answered on 8/2/2017 by InyoPools Product Specialist Lennox H.

Hi, Cindy. You can view the dimensions of the pump seal by clicking on this Product Dimensions link.
 Reply


?     Asked on 10/29/2017by jim

I have a Pentair superflow 2HP pool pump p/n: 340040, SF N1 2A HP, which is leaking at bottom between the pump and motor and I am wanting to know what is the correct repair kit so I can fix it. Thanks!
 Reply

A  Answered on 10/30/2017 by InyoPools Product Specialist Lennox H.

Hi, Jim. Replacing the Pump Seal will resolve your issue. This Pump Seal - PSR200 is the correct size for that model pump. 
 Reply


?     Asked on 11/16/2017by Rick

Will this seal fit the Aqua-Flo 05334012-2040 spa pump?
 Reply

A  Answered on 11/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Rick. Yes, this Pump Seal 200 - PSR200 will fit the Aqua-Flo 05334012-2040 model spa pump. 
 Reply


?     Asked on 5/2/2018by wallace simpson

I have a Pentair 2hp 2sp model #DYNII-N2-2 Motor with a DYNMO Model #DYNII-N2 pump. The pump shaft seal between the motor and pump is leaking. Which seal do I need.
 Reply

A  Answered on 5/3/2018 by InyoPools Product Specialist Hector F.

The main shaft seal for the Dynamo pool pump is part number 5250-104 for the generic one or you can get the complete seal kit being the GOKIT46. You can view the parts diagram here if you would like to view the other types of main shaft seals that you can use as well.  
 Reply


?     Asked on 5/23/2018by Inyo Visitor

I have a dura glas swimming pool pump 518R with a 5/8" shaft. Would I get the pump seal 200?
 Reply

A  Answered on 5/25/2018 by InyoPools Product Specialist Lennox H.

Hi. You could use this Shaft Seal with the Sta-Rite Dura Glas Pump. If you have the Seal Insert, it can just be removed. 
 Reply


?     Asked on 5/30/2018by Ruth

Is this the correct seal for a Jacuzzi model # S1LRT9-6?
 Reply

A  Answered on 6/3/2018 by InyoPools Product Specialist Lennox H.

Hi, Ruth. This Pump Shaft Seal will fit the S1LRT9-6 model pump. 
 Reply


?     Asked on 6/3/2018by tim

I have pump housing part number 347983 is this correct shaft seal for my optiflow nt1 11/2
 Reply

A  Answered on 6/3/2018 by InyoPools Product Specialist Lennox H.

Hi, Tim. Yes, this the correct Pump Shaft Seal for the Optiflo pump. . 
 Reply


?     Asked on 7/8/2018by Inyo Visitor

Will this work for a Stark USA pump model 75038?
 Reply

A  Answered on 7/8/2018 by InyoPools Product Specialist Lennox H.

Hi. Yes, this Pump Shaft Seal - PSR200 will fit the Stark USA Pump model 75038. 
 Reply


?     Asked on 10/19/2018by Dick

There are no markings on the pump. It was installed with a polaris system. the motor shaft is 5/8". The motor is a centurion B668. Is it likely that this part will fit?

 Reply

A  Answered on 10/19/2018 by InyoPools Product Specialist Patrick P.

Hi Dick, You have the Letro LA01N Booster Pump and you will require the PSR1000 Shaft Seal. Here is an article we put together on How to Replace a Shaft Seal on a Booster Pump which you may find helpful when you tackle this project.
 Reply


?     Asked on 11/25/2018by Ken

Need this rubber gasket for Jacuzzi Magnum Force and a couple other items. Do not see this on list. Can you assist?
 Reply

A  Answered on 11/26/2018 by InyoPools Product Specialist Hector F.

Yes, please click here to view the parts diagram for that pump with all seals and gaskets listed. You can also purchase the GOKIT14 which has all of the seals and gaskets for your pump model. 
 Reply


?     Asked on 2/26/2019by FLO Master XP2

Hello, will the shaft Seal PSR-200 works together with the FLO Master XP2 pump? Thks Peter
 Reply

A  Answered on 2/26/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this Pump Shaft Seal 5/8" - PSR-200 will fit the FloMaster XP2 pump. 
 Reply


?     Asked on 4/25/2019by Mark Totten

I have a pentair superflo pump that is not leaking externally but is not drawing enough to fill the pump cavity with water (air pocket approximately tennis ball size and bubbles coming out return jets). Could this be a seal problem?

 Reply

A  Answered on 4/25/2019 by InyoPools Product Specialist Lennox H.

Hi, Mark. The pump shaft seal will NOT cause this issue. I suggest replacing the Cover O-ring - 357255, Drain Plug O-ring - 192115 and or the Union O-ring - 350099
 Reply


?     Asked on 5/6/2019by James powers

Will this work for a turbo king pump #DYNII-NI-1.5
 Reply

A  Answered on 5/6/2019 by InyoPools Product Specialist Hector F.

Yes this is the correct shaft seal for your model pump. 
 Reply


?     Asked on 6/4/2019by Dennis

i have a A.O. Smith motor (HP 1.0 SPL (2 speed) PN 7-186554-01. need to replace the pump shaft seal, and impeller not sure if this is the correct one i need? Looks like S15LR-6 is the replacement motor, not 100% sure on that.
 Reply

A  Answered on 6/6/2019 by InyoPools Product Specialist Hector F.

So these seals and gaskets for the pumps are based on the model of the front pump housing that the motor bolts to. You can call in with that information or you cam email images of that housing to upload@inyopools.com so we can confirm.
 Reply


?     Asked on 6/18/2019by Josh Stegner

I have a superflo 1.5hp I need a shaft seal
 Reply

A  Answered on 6/19/2019 by InyoPools Product Specialist Hector F.

Yes, this is the correct shaft seal for your pump model. 
 Reply


?     Asked on 6/29/2019by kathy

hi, does the seal shut off on the diameter of the motor shaft ?
 Reply

A  Answered on 6/30/2019 by InyoPools Product Specialist Lennox H.

Hi, Kathy. When the two pieces of the shaft seal mate, it stops water from leaking out of the pump into the motor.  
 Reply


?     Asked on 7/12/2019by Brad

Will this work on a Jacuzzi 7LRA-S1/A pump?

 Reply

A  Answered on 7/12/2019 by InyoPools Product Specialist Matt L.

Yes, the correct standard shaft seal for the Jacuzzi LR Series old style is the PSR-200.
 Reply


?     Asked on 7/18/2019by Terry.N

Will this seal work on bestway everflow 1500 gallon pump

 Reply

A  Answered on 7/18/2019 by InyoPools Product Specialist Lennox H.

Hi, Terry.N. Unfortunately, we do not have any specs on the shaft seal used with the Bestway Everflow pumps. 
 Reply


?     Asked on 9/30/2019by ANDREW FYVIE

Hi .... just purchased a replacement motor ecm16squ, and a 32salt kit. My pool converted to chlorine 5 years ago. Unfortunately the shaft seal from the kit broke on me. Is there a replacement seal I can order? Old pump model is a Pentair whisperflo 177450.
 Reply

A  Answered on 9/30/2019 by InyoPools Product Specialist Hector F.

The standard shaft seal for the Whisperflo pump is the part number 5250-106
 Reply


?     Asked on 4/11/2020by james Michaud

What is the difference between the psr-100 and the psr-200 ?
 Reply

A  Answered on 4/15/2020 by InyoPools Product Specialist Hector F.

These seals have different dimensions. In order to confirm the correct shaft seal for your pump, we will need to know the make and model of the pump. If you cannot locate this information please send us a few images of the complete pump to upload@inyopols.com so we can assist. 
 Reply


?     Asked on 4/28/2020by Danny

Does this PSR-200 fit Century B855 motor?
 Reply

A  Answered on 4/28/2020 by InyoPools Product Specialist Patrick P.

For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply

  • Commented on 8/9/2020 by Product Owner

    Need pool pump seal kit!

     Reply

    • Commented on 10/19/2020 by InyoPools Product Specialist Hector F.

      Suilagi, the seal kit for your pump in a chlorine swimming pool is the GOKIT2 and for a saltwater swimming pool is the GOKIT2SALT as you have the Hayward Super 2 series model pool pump.  
       Reply


?     Asked on 5/3/2020by gene reardon

could you give me the part numbers for shaft seal, impeller ring and housing gasket for B2859 motor
 Reply

A  Answered on 12/9/2020 by InyoPools Product Specialist Hector F.

For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply


?     Asked on 5/8/2020by Karen L

I’m looking for a replacement seal for my impeller. Are you able to let me know if this is the correct size seal based on the pictures I attached? It’s a Sundance spa.

 Reply

A  Answered on 12/8/2020 by InyoPools Product Specialist Hector F.

Hi Karen, for us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply

  • Commented on 12/8/2020 by Product Owner

    Thank you for your reply. I have since ordered and replaced the seal. Have a great night!
     Reply


?     Asked on 6/8/2020by Giovanni DiMaggio

Will this part work with the pentair optiflo? I have a leak between the motor and the pump coming out of the bottom of the shaft.
 Reply

A  Answered on 6/9/2020 by InyoPools Product Specialist Hector F.

Yes, this is the correct shaft seal for the Pentair Optiflo pool pump. 
 Reply


?     Asked on 6/28/2020by Pete

Will this seal fit a B985 Century pump?
 Reply

A  Answered on 10/22/2020 by InyoPools Product Specialist Hector F.

Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 6/30/2020by Richard Solis

Does this seal fit harris model 72729 pool pump?
 Reply

A  Answered on 10/22/2020 by InyoPools Product Specialist Hector F.

Hi Richard, the correct shaft seal will be part number PL1592
 Reply


?     Asked on 7/2/2020by Wayne Mauro

I have a century pool pump model ust1152. Will this seal kit work for me?

 Reply

A  Answered on 11/20/2020 by InyoPools Product Specialist Hector F.

For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply


?     Asked on 7/10/2020by Ed

I have a 2 speed waterway pump with Motor mod-f48A032A79R is this the right seal? Thanks, Ed

 Reply

A  Answered on 12/14/2020 by InyoPools Product Specialist Hector F.

Hi Ed, for us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply


?     Asked on 7/11/2020by Lawrence Lipinski

need a seal kit for Century ST 1152 pool pump motor can you recommend one
 Reply

A  Answered on 11/18/2020 by InyoPools Product Specialist Hector F.

Hi Lawrence, For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply


?     Asked on 7/14/2020by Marshall Hall

what is the difference between a PSR-200 and a PS-200 shaft seal?
 Reply

A  Answered on 11/17/2020 by InyoPools Product Specialist Hector F.

Hi Marshall, there is no difference between the PSR and PS200 shaft seals. These are merely alternate part numbers as many products in the swimming pool industry have alternate part numbers. 
 Reply


?     Asked on 7/17/2020by Bob Sommers

Will this fit the Hayward SP3007EE ?
 Reply

A  Answered on 11/17/2020 by InyoPools Product Specialist Hector F.

Could you send us a few photos of your pump? Please take a close up shot of the pump label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 7/21/2020by Tom

Installing a PSR-200 seal, and i noticed it can easily separate from the bottom piece. Is this normal? Included pic Thanks

 Reply

A  Answered on 10/28/2020 by InyoPools Product Specialist Hector F.

Hi Tom, these shaft seal collars are known to come apart on an older seal but not so much on a new one. 
 Reply


?     Asked on 7/22/2020by STEVE

is this correct seal for SP1593
 Reply

A  Answered on 10/27/2020 by InyoPools Product Specialist Hector F.

Hi Steve, the shaft seal for the model Hayward Power Flo Matrix SP1593 pool pump is part number 5111-03 for a chlorine swimming pool and part number 5250-230 for a saltwater pool. 
 Reply


?     Asked on 8/6/2020by Nicholas Mendez

I have a Pentair 340037 Superflo pump, it is leaking from by the impeller on the motor side, will this seal fit my pump and is it the likely cause?
 Reply

A  Answered on 10/30/2020 by InyoPools Product Specialist Hector F.

Hi Nicholas, for the Pentair Superflo series pool pump this is the standard shaft seal most often used with chlorine swimming pools. Also, when there is a leak on the rear side of the pump seal plate at the face of the motor that sometimes runs underneath the motor, it is often due to this seal failing. 
 Reply


?     Asked on 8/10/2020by jim

How fast can this ship ???
 Reply

A  Answered on 10/29/2020 by InyoPools Product Specialist Hector F.

Hi Jim, this shaft seal is currently in stock and ready to ship. The average delivery lead time is approximately 3-7 business days. You can also expedite the order by selecting the shipping method once the item is in your cart and will give you an estimated shipping cost. 
 Reply


?     Asked on 9/30/2020by James Paul Brashears

Will this work with a Century b130?
 Reply

A  Answered on 10/15/2020 by InyoPools Product Specialist Hector F.

The shaft seals or seal kits are actually based on the model name or number of the front pump wet end housing that the motor attaches to. 
 Reply


?     Asked on 10/20/2020by Mark

Do you have a pump shaft seal for the Sequence 750 pump? The MDM part number is 750-4014. It looks very very similar to the one you're selling here. Thanks!
 Reply

A  Answered on 10/21/2020 by InyoPools Product Specialist Joe S.

Hello Mark, after review we found based on the Sequence 750 Series Pumps models this would be the correct shaft.
 Reply


?     Asked on 12/24/2020by Vicki Lasker

Correct seal kit for Century USQ1152 motor C48L2PA105C5

 Reply

A  Answered on 12/28/2020 by InyoPools Product Specialist Joe S.

Thank you for the information on your motor. To better assist you, we will also need the make and model of your pump. This information is typically listed on a label on the housing area, opposite the motor. Once we have this information, we can better answer your questions/concerns. Please let us know if you need help locating this information on your pump.
 Reply


?     Asked on 12/24/2020by Vicki Lasker

What is the Correct seal kit for Century USQ1152 motor? Model C48L2PA105C5 See pictures

 Reply

A  Answered on 12/28/2020 by InyoPools Product Specialist Hector F.

Hi Vicki, Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or provide those to our online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
 Reply

  • Commented on 12/28/2020 by Product Owner

    More pictures attached

     Reply

    • Commented on 2/17/2021 by InyoPools Product Specialist Hector F.

      Hi Vicki, you have an Everbilt pool pump which we, unfortunately, do not carry parts for. You may want to contact the retailer that you purchased it with as they may have further advice. 
       Reply


?     Asked on 1/10/2021by David

What is the part number of the shaft seal for Century 1.0 HP Square Flange 56Y Full Rate Motor - B2848?
 Reply

A  Answered on 1/11/2021 by InyoPools Product Specialist Joe S.

Thank you for the information on your motor. To better assist you, we will also need the make and model of your pump. This information is typically listed on a label on the housing area, opposite the motor. Once we have this information, we can better answer your questions/concerns. Please let us know if you need help locating this information on your pump.
 Reply

  • Commented on 1/12/2021 by Product Owner

    The pump is Whisper Flo, please see attached photos.

     Reply

    • Commented on 2/17/2021 by InyoPools Product Specialist Hector F.

      Hi David, the seal kit for the Pentair Whisperflo in a chlorine swimming pool is the GOKIT32 and for a saltwater swimming pool is the GOKIT32SALT
       Reply


?     Asked on 5/20/2021by Melissa

What shaft seal do I need for my pool pump

 Reply

A  Answered on 5/20/2021 by InyoPools Product Specialist Patrick P.

Could you send us a few photos of your pump and motor? Please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply

  • Commented on 5/20/2021 by Product Owner

    Ok

     Reply

    • Commented on 5/21/2021 by InyoPools Product Specialist Danny R.

      Thanks Melissa,I would suggest GoKit-47 for your DyanMax pool pump
       Reply

      • Commented on 5/21/2021 by Product Owner

        Can you tell me what impeller we need for this pump?
         Reply


?     Asked on 6/28/2021by Paul C Manning

will this seal fit the Pentair Pinnacle 34-2854 pump? ours is leaking out of the back side of the pump
 Reply

A  Answered on 6/28/2021 by InyoPools Product Specialist Patrick P.

Yes this shaft seal is used on the Pentair Pinnacle.
 Reply


?     Asked on 10/20/2021by Sandra

I have an old Pinnacle pump, the impeller has these numbers printed: 35-5041 and 35-5043 Will this work, I already tried ordering shaft seals from other stores and none of them fit. I am adding a photo of a seal that was in the pump, facing the impeller.

 Reply

A  Answered on 10/21/2021 by InyoPools Product Specialist Craig C.

Hello Sandra.  The Pump Shaft Seal 5/8" PSR-200 is a compatible shaft seal for the Pentair Pinnacle Pool Pump.  Please be sure to install the two parts of the shaft seal in the correct orientation to prevent leaking.  Pump Shaft Seal 5/8" - PSR-200   Attached please find an exploded parts diagram of the Pentair Pinnacle Pool Pump for reference.   Pentair / Pac Fab Pinnacle
 Reply


?     Asked on 11/4/2021by Mike Perez

I have a century pump motor: Cat B662 P/N: 7-177375-22 Type: CX Frame: 56Y Its installed on an arneson booster pump metal housing running a Polaris cleaner. The pump housing is for a vertical pump motor, see photos for install, need to replace the pump shaft seal, and i purchased this PSR-200 and its seems to be too long and the motor will bind when installed and will not run properly?

 Reply

A  Answered on 11/5/2021 by InyoPools Product Specialist Rich N.

Hi Mike, that should all fit together just fine.  Be sure that there is nothing remaining of the old shaft seal in the End Bell on your Arneson Booster Pump or stuck on the impeller. 
 Reply


?     Asked on 1/15/2022by Inyo Visitor

Can US Seal PS-200 work with Jandy Stealt SHPF2.0 / SN P08FG1235.
 Reply

A  Answered on 1/15/2022 by InyoPools Product Specialist Craig C.

Hello.  The US Seal PS-200 is NOT compatible with the Jandy Stealth Pool Pump model SHPF 2.0, s/n P08FG1235.  The Jandy Shaft Seal R0479400 is the correct shaft seal.    Jandy Pump Shaft Seal 5/8" - R0479400
 Reply


?     Asked on 1/21/2022by lenny

Is this the seal I need for my Dura-glas spa 3/4 hp pump, part number shaft seal 17304-0100.
 Reply

A  Answered on 1/21/2022 by InyoPools Product Specialist Rich N.

Hi Lenny, yes, this is the same as part number 17304-0100 and is used on the Dura-Glas pumps made after 1998.  
 Reply

  • Commented on 1/21/2022 by Product Owner

    Thanks, I will order it now.
     Reply


?     Asked on 3/18/2022by Stephen Harrell

What is the order and direction of the Pump Shaft Seal 5/8" - PSR-200 when putting it on the shaft
 Reply

A  Answered on 3/18/2022 by InyoPools Product Specialist Rich N.

Hi Stephen, our guide on How To Replace a Pool Motor Shaft Seal will show you exactly how to install it.
 Reply


?     Asked on 5/12/2022by John chomiak

Will this work for a Century UST 1102, 1 hp pump?

 Reply

A  Answered on 5/12/2022 by InyoPools Product Specialist Craig C.

Hello John.  A shaft seal is specific to the manufacturer/model of the pump and not the motor, UST1102.  The attached photo identifies the pump as a Hayward Super Pump or Hayward Super II Pump.  In either circumstance, the motor shaft seal is Pump Shaft Seal 3/4" PS-201    
 Reply


?     Asked on 7/1/2022by RALPH A FUCHS

Will the PSR200 pump shaft seal fit my jacuzzi S15LR-E pump.

 Reply

A  Answered on 7/1/2022 by InyoPools Product Specialist Craig C.

Hello Ralph.  The Pump Shaft Seal 5/8" - PSR-200 is compatible with the Jacuzzi Pool Pump model S15LR-E.  Attached please find the Jacuzzi LR and SLR Series exploded parts diagram for reference.
 Reply


?     Asked on 7/20/2022by Eric Spreen

Is this correct for my pump

 Reply

A  Answered on 7/20/2022 by InyoPools Product Specialist Craig C.

Hello Eric.  Attached please find the Aqua-Flo XP & XP2 exploded parts diagram.  The Pump Shaft Seal 5/8" - PSR-200 is the correct pump shaft seal.
 Reply


?     Asked on 10/17/2022by harold BOSS

is this the right seal for pentair model # SF-N1-2-1/2A/340041
 Reply

A  Answered on 10/17/2022 by InyoPools Product Specialist Craig C.

Hello Harold.  The Pump Shaft Seal 5/8" - PSR-200 is the correct shaft seal for the Pentair SuperFlo model SF-N1-2-1/2A, 340041.  Attached please find the Pentair SuperFlo Pump exploded parts diagram for reference.  
 Reply